Panasonic TY-42PV30NZ User manual

Designed specifically for 42PV30A
TY-42PV30NZ BUS4 04
IMPORTANT: DO NOT PUSH OR PULL THE TV TO MOVE THE CABINET.
Please follow these assembly instructions.

Left Location Pin
Right Location Pin
Packer
Back side
Moulding
Cable Pin
IMPORTANT:- MISSING PARTS CANNOT BE REPLACED UNLESS THE INFORMATION REQUESTED ABOVE IS FULLY SUPPLIED.
1. MODEL NUMBER OF THE UNIT PURCHASED
6. SERIAL NUMBER OF THE UNIT PURCHASED
OR CALL YOUR CLOSEST SERVICE CENTRE, PROVIDING THE DETAILS BELOW.
FOR MISSING OR FAULTY PARTS: PLEASE RECHECK YOUR PACKAGING TO ENSURE THAT PARTS ARE MISSING, THEN WRITE
3. DESCRIPTION OF THE MISSING PART
2. COPY OF YOUR PURCHASE SLIP
5. QUANTITY OF THE PARTS MISSING
4. PART NUMBER OF THE MISSING PART
www.criterionfurniture.com
(LOCATED ON UNDERSIDE OF TOP OF UNIT)
POST DETAILS AS REQUESTED IN 1-6 INCLUSIVE TO:-
MAKE SURE YOU INCLUDE YOUR ADDRESS,
NEW ZEALAND - CALL 0800 CRITERION (0800 274-837) OR FAX [phone].
CRITERION FURNITURE (NZ) LTD,
AUCKLAND 1730,
NEW ZEALAND.
P.O. BOX 58-646,
GREENMOUNT,
AUSTRALIA - AFTER SALES SERVICES: CALL - 02 9453 9555
Customer Service
M19721A1PO
M19722A1PO
M19723A1PO
M19591B2PO
M19595A2PO
M19592A1DF
M19619B1DF
M19596A1PO
M19597A1PO
PG0303A0
P815056
P816177
P816178A
P816179A
P816172
MH1101A0
1
1
1
2
2
2
2
2
2
2
5
2
1
1
2
1
Top
Packer
Base
Front Rail
Front Mouldings
Back Side Mouldings
Side Mouldings
Left Glass Bracket
Right Glass Bracket
Glass Shelf
Castor
Cable Holder
Right Location Pin
Left Location Pin
Threaded Rod
Hardware Pack
Part Number
Quantity
Unpack & Identify Parts
CARTON CONTENTS
Part Description
Front Rail
Castor
Base
Glass shelf
Front
Moulding
Right
Glass Bracket
Side Moulding
Cable holder
Left
Glass Bracket
Top

STEP 1
1.Fasten5CastorstotheBaseasshown.
2. Insert Wooden Dowels as shown above.
x10
P800201 x 16
Base (underside)
Castor
P860045

Allen key

STEP 5
1. Fit Sleeve Nut at one end of each Threaded Rod using an Allen Key.
2. Insert Threaded Rod into Assembly through Base as shown.
3. Fit another Sleeve Nut at other end of Threaded Rod from Top and tighten it turning both Allen Keys in opposite
direction of each other.
Threaded Rod
P816172 x 2
Sleeve Nut
P860256 x 4
Allen key
Allen key
Threaded
Rod

STEP 6
1. Fit 2 Small Connecting Rods to each Front Rail as shown.
2. Fit Front Mouldings to Base as shown.
3. Fit Front Rails on to Front Mouldings as shown.
Front
Rail
Front Rail
Front Rail
Front
Moulding

STEP 7
1. Fasten the Front Rails and Front Mouldings to the Base while holding them flush with outside edge of Stand using 2
Locking Screws.
View from front of Stand
Front Rail Front Rail
Front
Moulding
Front
Moulding
Ensure that Front Rail, Front Moulding and
Base are all flush on outside edge.

1. Tighten the 4 pre-fitted Cams in Top, by turning them clockwise.
STEP 8

STEP 9
1. Fasten the Glass Brackets to Side Mouldings using Screws as shown.
Right Glass Bracket x 2
Left Glass Bracket x 2
P860246 x 8

STEP 10
1. Slide each Glass Shelf into Glass Brackets and tighten Grub Screws from the underside of brackets as shown, make
sure the Back Edge of Glass Shelf is flush with Glass Bracket.
The curved part of the Glass should be at the front.

STEP 14
2. While Gently pushing the Plasma TV back to ensure the TV is standing straight on the stand, tighten the TV with the Bolts as
shown below.
1. With help of an Assistant, lift the Television onto Pins ensuring that the Pins line up with the Holes in base of Television.
Ensure TV is standing straight
on the stand before you tighten
the bolts.

Once Cables are behind Pins,
slide the Cable Pins across into
the Side Moulding.
CABLE MANAGEMENT
Back Side Moulding
Side Moulding
1. With Cable Pins pushed into Back Side Mouldings, place Cables behind pins, then slide Pins across into the Side Mouldings.
Congratulations you have now finished the assembly for your Panasonic Television Stand.