Panasonic S24GPWR User manual

Operation
Manual
for CLI
Switch-S24GPWR
Model Number: PN25249
Thank you for purchasing our product.
This manual provides important information about safe and proper operations
of this Switching Hub.
Please read "Important Safety Instructions" on pages 1 to 4 before use.
For target model names and numbers, refer to the next page.
Under all circumstances, customer disassembling of this Switching Hub voids
the warranty.

The target model for this Operation Manual is as follows.
Model name Model number Firmware version
Switch-S24GPWR PN25249-ID
PN25249-TH
PN25249-MY
PN25249-SG
1.0.0.07 or higher
2

Important Safety Instructions
Please Follow the Instructions
3
This chapter contains important safety instructions for preventing bodily injury
and/or property damage. You are required to follow them.
■Severity of bodily injury and/or property damage, which could result from incor-
rect use of the Switching Hub, are explained below.
This symbol indicates a potential hazard that could result in
serious injury or death.
This symbol indicates safety instructions.Deviation from these
instructions could lead to bodily injury and/or property dam-
age.
■The following symbols are used to classify and describe the type of instructions to
be observed.
This symbol is used to alert users
to what they must not do.
This symbol is used to alert users
to what they must do.
●Do not use power other than AC 100-240 V.
Deviation could lead to fire, electric shock, and/or equipment failure.
●Do not handle the power cord with wet hand.
Deviation could lead to electric shock and/or equipment failure.
●Do not handle this Switching Hub and connection cables during a thun-
derstorm.
Deviation could lead to electric shock.
●Do not disassemble and/or modify this Switching Hub.
Deviation could lead to fire, electric shock, and/or equipment failure.
●Do not damage the power cord. Do not bend too tightly, stretch, twist,
bundle with other cord, pinch, put under a heavy object, and/or heat it.
Damaged the cord could lead to fire, short, and/or electric shock.
●Do not put foreign objects (such as metal or combustibles) into the
opening (such as twisted pair port, console port), and do not drop them
inside the Switching Hub.
Deviation could lead to fire, electric shock, and/or equipment failure.
●Do not connect equipment other than 10BASE-T/100BASE-TX/
1000BASE-T to a twisted pair port.
Deviation could lead to fire, electric shock, and/or equipment failure.

●Do not please this Switching Hub in harsh environment(such as near
water, high humid, and/or high dust).
Deviation could lead to fire, electric shock, and/or equipment failure.
●Do not place this Switching Hub under direct sunlight and/or high tem-
perature.
Deviation could lead to high internal temperature and fire.
●Do not install this Switching Hub at a location with continuous vibration
or strong shock, or at an unstable location.
The Switching Hub may fall off, leading to injury and/or equipment
failure.
●Do not put this Switching Hub into fire.
Deviation could lead to explosion and/or fire.
●Do not use the supplied power cord for anything other than this prod-
uct.
Deviation could lead to fire, electric shock, and/or equipment failure.
●Use the bundled power cord (AC 100 - 240V specifications).
Deviation could lead to electric shock, malfunction, and/or equipment
failure.The warranty does not cover any problems resulting from the
use of any power cord other than the one supplied.
●Unplug the power cord in case of equipment failure.
Deviation such as keeping connected for a long time could lead to fire.
●Connect this Switching Hub to ground.
Deviation could lead to electric shock, malfunction, and/or equipment
failure.
4

●Connect the power cord firmly to the power port.
Deviation could lead to electric fire, shock, and/or malfunction.
●Unplug the power cord if the Status/ECO LED (Status/ECO mode),
blinks in orange (system fault).
Deviation, such as keeping connected for a long time, could lead to
fire.
●Handle the Switching Hub carefully so that fingers or hands may not be
damaged by twisted pair port, console port, or power cord hook block.
●To connect a power receiving equipment supporting IEEE802.3af to
this Switching Hub, use a cable rated Cat5e or higher.
Using other cables may result in heat generation, ignition, and/or
equipment failure.
Important Notice for Measures against Failures
Caused by Lightning Strikes
● When connecting devices (especially outdoor devices) prone to lightning
strikes, such as network cameras or wireless access points, to a twisted pair
port of this Switching Hub, overcurrent and/or overvoltage caused by light-
ning may affect this Switching Hub through a twisted pair cable, causing
equipment failure. When connecting such devices, we strongly recommend
installing a lightning arrester (SPD; Surge Protective Device) at the twisted
pair port side of the Switching Hub.
● Overcurrent and/or overvoltage caused by lightning may affect this
Switching Hub through a power source connected to the power port and/or
a grounding line, causing equipment failure. When there is a possibility of
overcurrent/overvoltage from lightning affecting this Switching Hub from a
power source and/or a grounding line, we strongly recommend installing a
lightning arrester (SPD; Surge Protective Device) at the power port side of
the Switching Hub.
● In case this Switching Hub fails due to lightning strikes, repair charges will
apply even during the warranty period.
5

6
Basic Instructions for the Use of This Product
●For inspection and/or repair, consult the retailer.
●Use commercial power supply from a wall socket, which is close and easily
accessible to this Switching Hub.
●Unplug the power cord when installing or moving this Switching Hub.
●Unplug the power cord when cleaning this Switching Hub.
●Use this Switching Hub within the specifications. Deviation could lead to mal-
function.
●Be sure to confirm that this Switching Hub does not move or fall under the
weight of the cables when mounting with magnets. Connect cables while hold-
ing the Switching Hub down.
●Securely attach this Switching Hub to the wall with screws when mounting it in
a high location.When mounting this Switching Hub with magnets in a high loca-
tion, a fall of the Switching Hub could lead to injury and/or equipment failure.
●Do not place a floppy disk or magnetic card near the magnet. Deviation could
lead to corruption of the data.
●Do not move this Switching Hub when attached to the desk. Deviation could
lead to scratches on the painted surface.
●Do not touch the metal terminal of the RJ45 connector, the modular plug of
connected twisted pair cable. Do not place charged objects in the proximity of
them. Static electricity could lead to equipment failure.
●Do not put the modular plug of the connected twisted pair cable on objects that
can carry static charge, such as carpet. Do not place it in the proximity. Static
electricity could lead to equipment failure.
●Do not put a strong shock, including dropping, to this Switching Hub. Deviation
could lead to equipment failure.
●Before connecting a console cable to the console port, discharge static electric-
ity, for example by touching metal appliance (do not discharge by touching this
Switching Hub).

7
1. Panasonic will not be liable for any damage resulting from the operation not in
accordance with this operation manual, or loss of communications, which may or
may not be caused by failure and/or malfunction of this device.
2. The contents described in this document may be changed without prior notice.
3. For any questions, please contact your dealer.
* Brands and product names in this document are trademarks or registered trademarks
of their respective holders.
●Do not store and/or use this Switching Hub in the environment with the charac-
teristics listed below.(Store and/or use this Switching Hub in the environment in
accordance with the specification.)
- High humidity. Possible spilled liquid (water).
- Dusty. Possible static charge (such as carpet).
- Under direct sunlight.
- Possible condensation. High/low temperature exceeding the specifications
environment.
- Strong vibration and/or strong shock.
●Please use this Switching Hub in place where ambient temperature is from 0 to
45 ℃ .Fail- ure to meet the above conditions may result in fire, electric shock,
breakdown, and/or malfunction. In addition, do not cover the bent hole of this
Switching Hub.Devia- tion could lead to high internal temperature, equipment
failure and/or malfunc- tion. If used at a temperature out of the operating tem-
perature range, the protection equipment becomes activated and PoE power
supply stops.
●Failure to satisfy the conditions above may result in a fire, electric shock, equip-
ment failure, and/or malfunction. Such events are not covered by the warranty.
Do not block the ventilator of the Switching Hub. Blocked ventilator induces the
heat accumulation inside, causing equipment failure and/or malfunction. If used
at a temperature out of the operating temperature range, the protection equip-
ment becomes activated and PoE power supply stops.
●Do not stack Switching Hubs. When placing Switching Hubs side by side, leave a
minimum of 20 mm space them.
●When mounting Switching Hubs in a rack, leave a minimum of 20 mm space
between them.

8
Table of Contents
Important Safety Instructions ............................................................................. 3
Basic Instructions for the Use of This Product ..................................................... 6
1. Command Hierarchy ................................................................................... 9
2. Displaying Basic Information ..................................................................... 12
3. Basic Switch Configuration ....................................................................... 13
3.1. System Administration Configuration ................................................... 13
3.2. IP Address Configuration ...................................................................... 15
3.3. Port Configuration ............................................................................... 16
3.4. Access Condition (Console and Telnet) Configuration ........................... 20
3.4.1.Configuration of Easy IP Address Setup Function ............................. 23
3.5. MAC Address Table Display and Registration Configuration .................. 24
3.6. Time Configuration .............................................................................. 27
3.7. ARP Table Display and Registration Configuration ................................ 28
4. Advanced Switch Configuration ............................................................... 29
4.1. VLAN Configuration ............................................................................. 29
4.2. Link Aggregation Configuration ........................................................... 31
4.3. Port Monitoring Configuration ............................................................. 32
4.4. QoS (Quality of Service) Configuration ................................................. 33
4.4. PoE Power Supply Function Configuration ............................................ 35
4.4.1.PoE Scheduler Configuration ........................................................... 36
4.5. Line Configuration ................................................................................ 40
4.5.1.Loop Detection and Blocking Configuration ..................................... 40
5. Displaying Statistic Information ................................................................ 42
6. Transferring Configuration Files ................................................................ 43
7. Firmware Upgrade ................................................................................... 44
8. Reboot ..................................................................................................... 45
8.1. Reboot Timer Function Configuration ................................................... 46
9. Exception Handler .................................................................................... 47
10. Ping Execution ......................................................................................... 48
11. Displaying and Configuring the System Log .............................................. 49
12. Saving Configuration Information ............................................................ 50
13. Displaying Configuration Information ....................................................... 51
14. Obtaining Technical Support Information ................................................. 52
15. Appendix ................................................................................................. 53
16. Troubleshooting ....................................................................................... 55
17. After-sales Service .................................................................................... 57

9
1. Command Hierarchy
There are four hierarchical levels in the command hierarchy.
(1) User mode:
The User mode is the mode right after login. Only limited operations are avail-
able.
(2) Privileged mode:
The Privileged mode allows to check the status of this Switching Hub and
manipulate the configuration file.
(3) Global configuration mode:
The Global configuration mode allows general configuration of this Switching
Hub.
(4) Interface configuration mode
The Interface configuration mode allows detailed configuration of this
Switching Hub, such as for each port or VLAN.
S24GPWR> enable
S24GPWR# configure
S24GPWR(config)# interface gi0/1
S24GPWR(config-if)# exit
S24GPWR(config)# exit
S24GPWR#
Fig. 1-1 Command hierarchy
enable command
・ The enable command enables to move from User mode to Privileged mode.
S24GPWR> ･････････････････････････ User mode
S24GPWR> enable ･･････････････････ User mode ⇒ Privileged mode
S24GPWR# ･････････････････････････ Privileged mode
S24GPWR# disable ･･････････････････ Privileged mode ⇒ User mode
S24GPWR> ･････････････････････････ User mode
disable command
・ The disable command enables to return from Privileged mode to User mode.
S24GPWR# ･････････････････････････ Privileged mode
S24GPWR# disable ･･････････････････ Privileged mode ⇒ User mode
S24GPWR> ･････････････････････････ User mode
configure command
・ The configure command enables to move from Privileged mode to Global con-
figuration mode.
S24GPWR# ･････････････････････････ Privileged mode
S24GPWR# configure ･･･････････････ Privileged mode
⇒ Global configuration mode
S24GPWR(config)# ･･････････････････ Global configuration mode

10
interface command
・ The interface command enables to move from Global configuration mode to
Interface configuration mode.
S24GPWR(config)# ･･････････････････ Global configuration mode
S24GPWR(config)# interface vlan1 ･･ Global configuration mode
⇒Interface
configuration mode (vlan1)
S24GPWR(config-if)# exit ･･･････････ Interface configuration mode
⇒ Global configuration mode
S24GPWR(config)# interface Gigabitethernet0/1
･･････････････････････････････････････ Global configuration mode
⇒Interface
configuration mode (interface1)
S24GPWR(config-if)# exit ･･･････････ Interface configuration mode
⇒ Global configuration mode
S24GPWR(config)# ･･････････････････ Global configuration mode
exit command
・ The exit command enables to return to the previous mode.
S24GPWR(config-if)# exit ･･･････････ Interface configuration mode
⇒ Global configuration mode
S24GPWR(config)# exit ･････････････ Global configuration mode
⇒ Privileged mode
S24GPWR# exit ･････････････････････ Privileged mode ⇒ User mode
S24GPWR> ･････････････････････････ User mode
end command
・ The end command enables to move from configuration modes to Privileged
mode.
S24GPWR(config-if)# end ･･･････････ Interface configuration mode
⇒ Privileged mode
S24GPWR# configure
S24GPWR(config)# end ･････････････ Global configuration mode
⇒ Privileged mode
logout command
・ The logout command enables to move from any of the modes to Menu screen.
S24GPWR(config)# logout ･･････････ Configuration modes ⇒ Menu
? command
・ Entering a question mark (?) in each mode displays executable elements in the
mode.
S24GPWR> ?
enable - Turn on privileged mode command
exit - Exit current mode and down to previous mode
logout - To logout from the CLI shell
ping - Send ICMP ECHO_REQUEST to network hosts
S24GPWR>

11
Fig. 1-2 ? Command
Re-entry assist
・ Entering the up arrow key displays a command that was entered immediately
before.
Candidate assist command
・ Entering a command followed by a question mark (?) displays candidates of suc-
ceeding arguments.
S24GPWR# configure
S24GPWR(config)# ip address
A.B.C.D - IP address (e.g. 10.0.0.1)
S24GPWR(config)# ip address
Fig. 1-3 Candidate assist command
Command autocomplete
For command and argument entries, when a word can be uniquely identified after
typing the first few letters, you can omit the remaining letters.
[Autocomplete examples]
・enable → en
・ show running-config → sh ru
[Example when autocomplete does not work]
・ co → Typing "co" does not run autocomplete because there are two candidates
"configure" and "copy."
Meanings of symbols in descriptions are as follows:
< > : Required - Make sure to enter this item.
{ | } : Choice - Select and enter either one.
[ ] : Optional - Enter as necessary.

12
2. Displaying Basic Information
Use the following commands in the "Privileged mode" to display basic information
of the Switching Hub.
Basic information display command
Privileged mode show sys-info
PN25249 Local Management System
Main Menu -> General Information
System up for: xxxday(s), xxhr(s), xxmin(s), xxsec(s)
Boot / Runtime Code Version: xx.xx.xx.xx/ xx.xx.xx.xx
Hardware Information
Version: Version1
DRAM / Flash Size: 128MB / 32MB
DRAM User Area Size: Free: xxxxxxxx bytes / Total: xxxxxxxx bytes
Administration Information
Switch Name:
System Address Information
MAC Address: xx:xx:xx:xx:xx:xx
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
Press any key to continue...
Fig. 2-1 Displaying basic information
(show sys-info)
Fig. 2-2 Execution example of the system information display command

13
3. Basic Switch Configuration
3.1. System Administration Configuration
Configure the host name, installation location and contact information in "Global
configuration mode." Confirm the configuration information by entering "show
sys-info" in "Privileged mode."
System information display command
S24GPWR#show sys-info
Host name configuration command
Global configuration mode hostname <hostname>
Host name delete command
Global configuration mode no hostname
Basic information display command
Privileged mode show sys-info
Note: When configuring a host name containing a space, enter it embracing with
double quotation marks (" ").
Example: hostname "Switch 1"

14
Example: Configuration example of the host name as PoESW-1, installation loca-
tion as Office-2F, and contact information as Manager
S24GPWR>
S24GPWR> enable
S24GPWR# configure
S24GPWR(config)# hostname PoESW-1
PoESW-1(config)# end
PoESW-1# show sys-info
System up for : 000day(s), 00hr(s), 00min(s), 00sec(s)
Boot / Runtime Code Version: x.x.x.xx / x.x.x.xx
Hardware Information
Version : Version1
DRAM / Flash Size : 64MB / 8MB
DRAM User Area Size : Free: xxxxxxxx bytes / Total: xxxxxxxx bytes
Administration Information
Switch Name : PoESW-1
Switch Location : Office-2F
Switch Contact : Manager
System Address Information
MAC Address : xx:xx:xx:xx:xx:xx
IP Address : 192.168.0.1
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.254
PoESW-1#
Fig. 3-1 Display of the host name, installation location and contact information con-
figuration (show sys-info)

15
3.2. IP Address Configuration
Configure the IP address settings of this Switching Hub in "Interface configuration
mode." Confirm the configuration information by entering "show ip conf" in "Privi-
leged mode."
IP address configuration command
Global configuration mode ip address
<ip-address> <mask> [<default-gateway>]
Default gateway configuration command
Global configuration mode ip default-gateway <ip-address>
IP address display command
Privileged mode show ip conf
Example 1: Configuration example of IP address as 192.168.0.1, subnet mask as
255.255.255.0, and default gateway as 192.168.0.254
S24GPWR> enable
S24GPWR# configure
S24GPWR(config)# ip address 192.168.0.1 255.255.255.0
S24GPWR(config)# ip default-gateway 192.168.0.254
S24GPWR(config)# end
S24GPWR# show ip conf
MAC Address : xx:xx:xx:xx:xx:xx
IP Address : 192.168.0.1
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.0.254
S24GPWR#
Fig. 3-2 Display of the IP address configuration
(show ip conf)
Note: Unless you configure these settings, you cannot use remotely connect to the
Switching Hub via Telnet or the web management function. Be sure to config-
ure. If you are unsure of the settings, consult the network administrator. Any
IP addresses on the local network must be unique, and no duplication is
allowed. In addition, you need to set the subnet mask and the default gate-
way, which are the same for other devices on the same subnet using this
Switching Hub.

16
3.3. Port Configuration
Configure port settings in "Interface configuration mode." Confirm the configura-
tion information by entering "show interface info" in "Privileged mode."
Port status enable command
Port status disable command
Port mode configuration command
Flow control enable command
Flow control disable command
Port name configuration command
Auto MDI enable command
IEEE802.3az (EEE) enable command
IEEE802.3az (EEE) disable commandd
Auto MDI disable command
MNO series power saving mode configuration command
Port information display command
Extension port information display command
MNO series power saving mode display command
Module information display command
Interface configuration mode no shutdown
Interface configuration mode shutdown
Interface configuration mode speed-duplex
{ auto | {10|100}-half | {10|100}-full }
Interface configuration mode flow-control
Interface configuration mode no flow-control
Interface configuration mode name < string>
Interface configuration mode mdix auto
Interface configuration mode line eee
Interface configuration mode no line eee
Interface configuration mode no mdix auto
Interface configuration mode line power-saving {disable | full | half}
Privileged mode show interface info
Privileged mode show interface name
Privileged mode show line configuration
Interface configuration mode getport

17
Example 1: Configuration example of port speed and flow control
S24GPWR> enable
S24GPWR# configure
S24GPWR(config)# interface GigabitEthernet0/1
S24GPWR(config-if)# speed-duplex 100-full
S24GPWR(config-if)# flow-control
S24GPWR(config-if)# end
S24GPWR# show interface info
Port Trunk Type Admin Link Mode Flow Ctrl Auto-MDI
---- ----- ----------- -------- ---- ------------ --------- --------
1 --- 100TX Enabled Down 100-FDx Enabled Disabled
2 --- 100TX Enabled Down Auto Disabled Disabled
3 --- 100TX Enabled Down Auto Disabled Disabled
4 --- 100TX Enabled Down Auto Disabled Disabled
5 --- 100TX Enabled Down Auto Disabled Disabled
6 --- 100TX Enabled Down Auto Disabled Disabled
7 --- 100TX Enabled Down Auto Disabled Disabled
8 --- 100TX Enabled Down Auto Disabled Disabled
9 --- 1000T Enabled Down Auto Disabled Enabled
10 --- 1000T Enabled Down Auto Disabled Enabled
11 --- 1000T Enabled Down Auto Disabled Disabled
12 --- 1000T Enabled Down Auto Disabled Disabled
13 --- 1000T Enabled Down Auto Disabled Disabled
14 --- 1000T Enabled Down Auto Disabled Disabled
15 --- 1000T Enabled Down Auto Disabled Disabled
16 --- 1000T Enabled Down Auto Disabled Disabled
17 --- 1000T Enabled Down Auto Disabled Disabled
18 --- 1000T Enabled Down Auto Disabled Disabled
19 --- 1000T Enabled Down Auto Disabled Disabled
20 --- 1000T Enabled Down Auto Disabled Disabled
More .....To stop press (n)
Fig. 3-3 Display of the port information (show interface info)

18
Example 2: Configuration example of port name
S24GPWR> enable
S24GPWR# configure
S24GPWR(config)# interface GigabitEthernet0/1
S24GPWR(config-if)# name gi0/1
S24GPWR(config-if)# eap-forward
S24GPWR(config-if)# end
S24GPWR# show interface name
Port Trunk Type Link Port Name
---- ----- ----------- ---- ---------------
1 --- 1000T Down Port_1
2 --- 1000T Down Port_2
3 --- 1000T Down Port_3
4 --- 1000T Down Port_4
5 --- 1000T Down Port_5
6 --- 1000T Down Port_6
7 --- 1000T Down Port_7
8 --- 1000T Down Port_8
9 --- 1000T Down Port_9
10 --- 1000T Down Port_10
11 --- 1000T Down Port_11
12 --- 1000T Down Port_12
13 --- 1000T Down Port_13
14 --- 1000T Down Port_14
15 --- 1000T Down Port_15
16 --- 1000T Down Port_16
17 --- 1000T Down Port_17
18 --- 1000T Down Port_18
19 --- 1000T Down Port_19
20 --- 1000T Down Port_20
More .....To stop press (n)
S24GPWR#
Fig. 3-4 Display of the extension port information (show interface name)

19
Example 3: Configuration example of MNO series power saving mode
S24GPWR> enable
S24GPWR# configure
S24GPWR(config)# interface GigabitEthernet0/1
S24GPWR(config-if)# line power-saving disable
S24GPWR(config-if)# end
S24GPWR# show line configuration
Port Link Trunk Type Mode Power-Saving EEE(802.3az)
---- ------ ----- ------ ----------- ------------ ------------
1 Down --- 1000T Auto Half Enabled
2 Down --- 1000T Auto Half Enabled
3 Down --- 1000T Auto Half Enabled
4 Down --- 1000T Auto Half Enabled
5 Down --- 1000T Auto Half Enabled
6 Down --- 1000T Auto Half Enabled
7 Down --- 1000T Auto Half Enabled
8 Down --- 1000T Auto Half Enabled
9 Down --- 1000T Auto Half Enabled
10 Down --- 1000T Auto Half Enabled
11 Down --- 1000T Auto Half Enabled
12 Down --- 1000T Auto Half Enabled
13 Down --- 1000T Auto Half Enabled
14 Down --- 1000T Auto Half Enabled
15 Down --- 1000T Auto Half Enabled
16 Down --- 1000T Auto Half Enabled
17 Down --- 1000T Auto Half Enabled
18 Down --- 1000T Auto Half Enabled
19 Down --- 1000T Auto Half Enabled
More .....To stop press (n)
S24GPWR#
Fig. 3-5 Display of the MNO series power saving mode (show line configuration)

20
3.4. Access Condition (Console and Telnet)
Configuration
Configure access conditions to the Switching Hub in "Global configuration mode."
Confirm the configuration information by entering "show terminal length" in "Privi-
leged mode."
Privileged mode show terminal length
Console timeout configuration command
Console configuration display command
Telnet server enable command
Telnet server disable command
User name and password configuration command
On-screen line numbers display command
Global configuration mode terminal length <LENGTH>
On-screen line numbers configuration command
Web server enable command
Web server disable command
LED base mode configuration command
LED base mode display command
Global configuration mode console inactivity-timer <minute>
Privileged mode show console
Global configuration mode telnet-server enable
Global configuration mode no telnet-server enable
Global configuration mode username <new username>
* After entering the user name, enter the old password and the new password (twice.)
Global configuration mode ip http server
Global configuration mode no ip http server
Global configuration mode led base-mode <status l eco>
Privileged mode show led base-mode