Panasonic HL-BT62S User manual

© Panasonic Corporation 2013 Unauthorized copy-
ing and distribution is a violation of law.
Order No. APGBIK1304003CE
ELECTRIC BUILT-IN OVEN
Model No.+/-BT62S
Model No.+/-BT62B
Destination UK
TABLE OF CONTENTS
PAGE PAGE
1 Safety Precautions----------------------------------------------- 2
2 Specifications ----------------------------------------------------- 3
3 General/Introduction -------------------------------------------- 4
4Features------------------------------------------------------------- 5
5 Location of Controls and Components ------------------- 7
6 Test Mode ----------------------------------------------------------14
7 Service Fixture & Tools----------------------------------------15
8 Disassembly and Assembly Instructions ---------------15
9 Wiring Connection Diagram ---------------------------------24
10 Exploded View and Replacement Parts List -----------26

2
1 Safety Precautions
1.1. Health & Safety
Note: When servicing the SCHOLTES oven, health and safety issues must be considered at all times. Specific safety issues are
listed below with their appropriate icon. These are illustrated throughout the service information to remind service people of the
health and safety issues
1.1.1. Electrical Safety
1.1.2. Electrostatic Discharge
1.1.3. Good Working Practices
1.1.4. Insulation Test
1.1.5. Sheet Metal Edges

3
2 Specifications
MODEL +/-BT62S / HL-BT62B
DESCRIPTION VALUE
OVEN CAPACITY 68 LITERS
ELECTRICAL SUPPLY 220-240V ~ -50-60Hz
NOMINAL POWER 3.00 kW
OVEN FAN MOTOR YES
GRILL HEATING ELEMENT 1.80 kW
TOP HEATING ELEMENT
BOTTOM HEATING ELEMENT 1.2 kW
FAN HEATING ELEMENT 2.0 kW
ENERGY CLASS A -20%
DISPLAY Touch control
COOLING FAN (transverse flow) YES, double speed
DOOR MICROSWITCH YES
ROTISSERIE MOTOR YES

4
3 General/Introduction
3.1. OVEN COOLING CIRCUIT AND FLUE
The oven is cooled by a tangential fan motor located above the oven cavity
The tangential cooling starts working (regardless of which cooking operation is selected) when the oven is switched on. The fan pro-
duces an air flow that lows out from an opening between the door and the front panel. The cooling air flow may also continue for a
short time after the oven is switched off.
Diagram of the air flow
Fresh air is sucked in by the tangential fan A at the bottom part
of the oven, passes through the door via the slit u nderneath
and in the back of the oven.
After circulating in the pu rposely designed ducts, it is captured
by the tangential fan a nd expelled from the front o pening
between the door and the front panel.
The cooling fan can work at two different speeds: full speed (only during the pyrolytic cycle) and half speed (normal operation). The
half speed operation is achieved by means of a load resistor connected series on the motor supply circuit.
Venting of the humidity from the oven cavity is achieved by means of a flue chimney connecting the cavity ceiling to the upper duct
of the cooling circuit.

5
4 Features
4.1. Oven cavity structure
A flue has been introduced on the top of the oven compart-
ment, which leads into the ventilation duct, allowing a
reduction in the humidity that is created inside the oven
compartment.
(In the case of a pyrolitic oven there is also a catalyser)
4.2. Oven cavity - construction
New volume created by the new assembly of the oven
compartment consisting of:
A- Roof
B- Band
Which includes
Side/Back/Side (one piece)
C- Bottom
the new oven cavity is no l onger constructed using spot
welding, but with mou lding instead, which e liminates any
sharp edges to facilitate cleaning and hygiene.

6
4.3. Heating element
The heating elements are the same for all the ovens and
are screwed in place from the inside the oven compart-
ment.
The bottom heating element is easily accessible since it is
removed by extracting it from the rear side of the appliance
4.4. New deflector
WARNING! Do not attach them upside down
Do not invert the 60L. deflector with the 68L. deflector

7
5 Location of Controls and Components
5.1. CONTROL PANEL
5.1.1. Keys description
In each menu only activated keys are described. The keys NOT described are NOT activated.
Any key pressing is followed by a short sound.
The ON-OFF key is prior to any other key. This key, even if is pushed together any other key, is accepted.
A counter is incremented every 1sec a key is held. In the case where a key has been held >= 25 sec continuously, the UI returns to
STAND-BY status; a single sound (0.5s) is emitted.
The key not lighted up are not accepted, and so no sound emission if pressed.
Pressing the key for 3sec, the UI returns to STAND-BY status and a single sound is emitted for 0.5sec.
5.1.2. First connection to the mains
The clock setting is done as follows:
Due to the statement above described (error after 25sec of continuously pressed key), a complete round of 24h while keeping
pressed the keys, must be done in less than 25sec.
5.1.3. Clock setting after first connection
The clock setting is done as follows:
on-off function selection temperature setting
duration timer delay timer descrease - minus
increase - plus minute minder clock set
PROCEDURE DISPLAY SHOWS KEYS USE
Power ON
D1 shows “00:00” NOT flashing
keys flash
Increase/decrease time, with higher speed is keep pressed
Waiting 3sec the time is fixed and D1 is fixed with the two central
dots flashing with frequency 1Hz. The display is set to CLOCK status
(see below §4 for status descriptions). Until keys are n ot
pressed, display remains in this status
PROCEDURE DISPLAY SHOWS KEYS USE
CLOCK status
D1 shows the clock
icon flashes Press for 3 seconds, D1 show the clock flashing
CLOCK setting D1 shows the clock flashing
Increase/decrease time, with higher speed is keep pressed
Waiting 3sec the time is fixed and D1 is fixed with the two central
dots flashing with frequency 1Hz.

8
5.1.4. USER INTERFACE (UI) status
Pressing key is possible to switch between these configuration (rolling):
5.1.5. Setup menu
This menu allow to set three possible oven configurations. Is possible to enter in this menu as follows:
Child lock: The program makes it possible to set the automatic control block for the oven 1 minute after using one of the controls.
Show Room: The program enables all the functions foreseen by the user interface but all the loads (heating elements and motors)
are always OFF.
Power configuration: heating elements are activated always in alternated way (never two elements together)
STATUS DISPLAY SHOWS KEYS USE
STAND-BY Display OFF the uP maintains the clock updated
CLOCK D1 shows the clock Set the clock (see §3)
ON
D1 Clock - D2 OFF
Oven lamp ON
If within 20sec any coo king function
or minute minder is selected, the UI
comes back (a utomatically) to
CLOCK status.
Set the UI in available different status
Select function.
Set a minute minder (see §7)
Enter the “Setup menu”
STATUS DISPLAY SHOWS KEYS USE
ON D1 shows the clock
D2 is OFF
Set the UI to STAND-BY status
Keep pressed for 5sec to enter in the Setup Menu
SETUP MENU
Child lock
D1 shows “ L ”
D2 shows “ OFF ”
Switch between ON-OFF condition shown on D2
Save configuration and exit from Setup Menu
Go to set the Show Room parameter
Wait for 3sec to automatically exit from Setup Menu and return to
CLOCK status
SETUP MENU
Show Room
D1 shows “ d ”
D2 shows “ OFF ”
Switch between ON-OFF condition shown on D2
Save configuration and exit from Setup Menu
Go to set the Show Power parameter
Wait for 3sec to automatically exit from Setup Menu and return to
CLOCK status
SETUP MENU
Power config
D1 shows “ HI ”
D2 shows “ PO ”
Switch between HI-LO condition shown on D1
Save configuration and exit from Setup Menu
Go to set the Show Room parameter
Wait for 3sec to automatically exit from Setup Menu and return to
CLOCK status

9
5.1.6. Manual cooking
*1 Example) The display of D2 at the time of 250°
STATUS DISPLAY SHOWS KEYS USE
ON
D1 shows Clock
D2 is OFF
If within 20se c any cooking function
or minute minder is selected, the UI
comes back (automatically) to
CLOCK status.
Set the UI to STAND-BY status
Select function.
Set a minute minder (see §7)
Enter the “Setup menu”
FUNCTION menu
D1 shows Clock
D2 shows default temperature
After 3sec without any key pressed,
the cooking function activates
Set the UI to STAND-BY status
Flashes to point at the ” Function setting ”
Modify the default temperature, steps of 5°C degrees
Set a minute minder timer
Set a duration timer
Select the function among the ones available
COOKING
Cycle
Preheating
D1 shows Clock
D2 shows set
temperature and
flashing ( preheating)
Keep pressed for 3 sec to set the UI to STAND-BY status
Quick pressing to switch ON-OFF the oven lamp
As described above
COOKING D1 shows Clock
Keep pressed for 3 sec to set the UI to STAND-BY status
Quick pressing to switch ON-OFF the oven lamp
As described above

10
5.1.7. Minute minder
Is possible to set a minute minder to activate an alarm after a countdown expire, without stopping any active cooking cycle
5.1.8. Duration Timer
Is possible to set a duration timer to activate an alarm after a countdown expire and also stopping any active cooking cycle;
the internal fan, the oven lamp and all elements are deactivated
STATUS DISPLAY SHOWS KEYS USE
ON Status
D1 shows Clock
D2 is OFF
If within 20sec any cooking
function or minute minder is
selected, the UI comes back
(automatically) to CLOCK
status.
Set the UI to STAND-BY status
Select function.
Set a minute minder
Enter the “Setup menu”
MINUTE MINDER Setting
D1 shows default 00:00
Icon and key flash
Set the UI to STAND-BY status
On fixed
Set a minute minder timer
Increase/decrease countdown, with higher speed if keep pressed.
Max possible countdown 4h.
3sec after the edit of last item, the countdown starts.
MINUTE MINDER Active
COOKING CYCLE NOT active
D1 shows countdown
D2 is OFF Keep pressed for 3 sec to set the UI to STAND-BY status
MINUTE MINDER Active
COOKING CYCLE active
D1 shows countdown
D2 shows cooking temperature
Quick pressing to switch ON-OFF the oven lamp
Change the countdown as described above
COUNTDOWN
expires
D1 shows “00:00” flashing
D2 is OFF
Emitted 10 sounds for each
minute and for the following
3 minutes
Keep pressed for 3 sec to set the UI to STAND-BY status
Quick set of a new countdown as above described
To stop the buzzer, the display still flashes
STATUS DISPLAY SHOWS KEYS USE
Manual Cooking
set or activated
D1 shows Clock
D2 shows the temperature
see §6
Set the UI to STAND-BY status
Set a duration timer
Set a minute minder (see §7)
DURATION
TIMER
Setting
D1 shows default 00:00
D2 shows the temperature
Icon and key flashes
If within 20sec any cooking function
or minute minder is selected, the UI
comes back (au tomatically) to
CLOCK status.
Set the UI to STAND-BY status
Set temperature and aborts the duration timer setting
Modify the set function (see §6)
Increase/decrease countdown, with higher speed if keep pressed.
Max possible countdown 13h.
3sec after the edit of last item, the countdown starts.
Set a Delay Timer ( see following §9)