Panasonic PT-DX800UK User manual

SPEC FILE
Pr duct Number : PT-DX800S/DX800K
PT-DX800LS/DX800LK
Pr duct Name : DLP™Projectors
As f December 2011. Specificati ns and appearance are subject t change with ut n tice.
SFD11M002-1
1/14
The PT-DX800LS and PT-DX800LK are n t equipped with a lens.

SPEC FI L E
PT-DX800S/DX800K/DX800LS/DX800LK
DLP™Projectors
As of December 2011
SFD11M002-1
2/14
ain unit
Power supply
Power consumption 120 V AC, 60 z
220–240 V AC, 50/60 z
DLP™ chip Panel size
Display method
Pixels
Lens PT-DX800S/DX800K
PT-DX800LS/DX800LK
Lamp
Screen size
Brightness*2
Center-to-corner uniformity*2
Contrast*2
Resolution
Scanning frequency DVI-D
RGB
YPBPR(YCBCR)
Video/S-Video
Optical axis shift
Keystone correction range
Installation
Terminals DVI-D IN
RGB 1 IN
R, G, B
Y, PB, PR(Y, CB, CR)
120 V AC, 7.5 A, 50/60 z
220–240 V AC, 4.3 A, 50/60 z
790 W (830 VA) (0.2 W with standby mode set to eco*1, 8Wwith
standby mode set to normal. Both with fan stopped.)
760 W (950 VA) (0.3 W with standby mode set to eco*1, 9 W with
standby mode set to normal. Both with fan stopped.)
17.8 mm (0.7 in) diagonal (4:3 aspect ratio)
DLP™ chip × 1, DLP™ system
786,432 (1,024 × 768) × 1, total of 786,432 pixels
Powered zoom/focus lenses (1.8 –2.5:1), F 1.7–1.9, f 25.6 –35.7 mm
Optional powered zoom/focus lenses and fixed-focus lens
300 W (max. 310 W) U M lamps (× 2) (dual lamp system)
1.27–15.24 m (50–600 inches) (1.27– 5.08 m (50–200 inches) with the
ET-DLE055), 4:3 aspect ratio
8,000 lumens (dual lamp, lamp mode: high)
90%
2,000:1 (full on/full off, contrast mode: high, brightness: 4,000 lumens)
1,024 × 768 pixels (Input signals that exceed this resolution will be
converted to 1,024 × 768 pixels.)
f: 15 k z–91 k z, fV:50 z– 85 z, dot clock: 162 M z or lower
f: 15 k z – 91 k z, fV:50 z –85 z, dot clock: 150 M z or lower
480i (525i): f 15.75 k z; fV60 z,
576i (625i): f 15.63 k z; fV50 z,
480p (525p): f 31.50 k z; fV60 z,
576p (625p): f 31.25 k z; fV50 z,
720 (750)/60p: f 45.00 k z; fV60 z,
720 (750)/50p: f 37.50 k z; fV50 z,
1035/60i: f 33.75 k z; fV60 z,
1080 (1125)/60i: f 33.75 k z; fV60 z,
1080 (1125)/50i: f 28.13 k z; fV50 z,
1080/25p: f 28.13 k z; fV25 z,
1080/24p: f 27.00 k z; fV24 z,
1080/24sF: f 27.00 k z; fV48 z,
1080/30p: f 33.75 k z; fV30 z,
1080/60p: f 67.50 k z; fV60 z,
1080/50p: f 56.25 k z; fV50 z
f: 15.75 k z, fV: 60 z [NTSC/NTSC4.43/PAL-M/PAL60]
f: 15.63 k z, fV: 50 z [PAL/PAL-N/SECAM]
Vertical: +50% (powered), horizontal: ±10% (powered)
(Vertical: +45%, horizontal: ±10% with the ET-DLE080)
Vertical: ±40° (±30° with the ET-DLE055 and ET-DLE080)
Ceiling/floor, front/rear
DVI-D 24-pin × 1, DVI 1.0 compliant, DCP compatible, for single link
only
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p,
1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,
VGA (640 × 480) – WUXGA*3(1,920 × 1,200), compatible with non-
interlaced signals only, dot clock: 25–162 M z
BNC × 5
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
D/VD, SYNC: igh impedance, TTL (positive/negative)
NOTE: HD/SYNC, and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
Specifications

SPEC FI L E
PT-DX800S/DX800K/DX800LS/DX800LK
DLP™Projectors
As of December 2011
SFD11M002-1
3/14
RGB 2 IN
R, G, B
Y, PB, PR(Y, CB, CR)
VIDEO IN
S-VIDEO IN
SERIAL IN
SERIAL OUT
REMOTE 1 IN
REMOTE 1 OUT
REMOTE 2 IN
LAN
Power cord length
Cabinet materials
Dimensions (W × × D) PT-DX800S/DX800K
PT-DX800LS/DX800LK
Weight PT-DX800S/DX800K
PT-DX800LS/DX800LK
Operation noise*2
Operating temperature
Operating humidity
Remote control unit
Power supply
Operation range*6
Dimensions (W × × D)
Weight
Supplied accessories
Optional accessories
Zoom lens (0.9 –1.0:1)
Zoom lens (1.3 –2.0:1)
Zoom lens (2.4 – 3.7:1)
Zoom lens (3.7– 5.6:1)
Zoom lens (5.5– 8.9:1)
Fixed-focus lens (0.8:1)
Ceiling mount bracket
Replacement lamp unit
Replacement filter unit
D-sub D 15-pin × 1
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
D/VD, SYNC: igh impedance, TTL (positive/negative)
NOTE: HD/SYNC, and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
BNC × 1, 1.0 Vp-p, 75 ohms
Mini DIN 4-pin × 1, Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms
D-sub 9-pin × 1 for external control (RS-232C compliant)
D-sub 9-pin × 1 for link control (RS-232C compliant)
M3 jack × 1 for wired remote control
M3 jack × 1 for link control
D-sub 9-pin × 1 for external control (parallel)
RJ-45 × 1 for network connection, 100Base-TX/10Base-T, compliant
with PJLink™
3.0 m (9 ft10 in)
Molded plastic
498 mm × 175 mm*4× 466 mm* 5(19-19/32˝ × 6-7/8˝ *4× 18-11/32˝ *5)
(with supplied lens)
498 mm × 175 mm*4× 432 mm* 5(19-19/32˝ × 6-7/8˝ *4× 17˝ *5)
(without lens)
Approx. 16.3 kg (35.9 lbs) (with supplied lens)
Approx. 15.4 kg (34.0 lbs) (without lens)
39 dB (dual lamp operation, lamp mode: high),
35 dB (dual lamp operation, lamp mode: normal)
0°–45°C (32°–113°F)*6
20%–80% (no condensation)
3 V DC (R6/AA type battery × 2)
Approx. 30 m (98 ft5 in) when operated from directly in front of the
signal receptor
51 × 176 × 23 mm (2˝ × 6-15/16˝ × 29/32˝)
Approx. 134 g (4.7 oz) (including batteries)
Power cord (× 1)
Power cord security lock (× 1)
Wireless/wired remote control unit (× 1)
Batteries for remote control (R6/AA type × 2)
ET-DLE080
ET-DLE150
ET-DLE250
ET-DLE350
ET-DLE450
ET-DLE055
ET-PKD56 (for high ceilings)
ET-PKD55S (for low ceilings)
ET-LAD60A
ET-LAD60AW (Twin Pack)
ET-EMF300
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
*1 When the standby mode is set to eco, network functions such as power on over the LAN network will not operate, and the serial output termi-
nal cannot be used. Also, only certain commands can be received for external control using the serial terminal.
*2 easurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*3 WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
*4 With legs at shortest position.
*5 Protruding parts not included.
*6 The operating temperature range is 0°C to 40°C (32°F to 104°F) when the fan control is set to High Altitude mode (for altitudes from 1,400 m to
2,700 m (4,593 ft to 8,858 ft) above sea level). Also, if the ambient temperature exceeds 40°C (104°F) (35°C (95°F) in High Altitude mode) when
the projector is being used with Lamp Select set to Dual and Lamp Power set to High, the light output may be reduced approximately 20% to
protect the projector.
*7 Operation range differs depending on environments.

498 (19-19/32)
416 (16-3/8)
423 (16-21/32)
466 (18-11/32)
43 (1-11/16)
9 (11/32)
77.5 (3-1/16)20 (25/32)
155 (6-3/32)
175 (6-7/8)
21 (13/16)
Dimensions
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
The illustration shows the PT-DX800S/DX800K.
SPEC FILE
PT-DX800S/DX800K/DX800LS/DX800LK
DLP™Projectors
As of December 2011
SFD11M002-1
4/14
Terminals
VD SYNC/HD B/PB G/Y
R
R/P
IN OUT
LAN
VIDEO IN RGB1 IN RGB2 IN DVI-D I N
S-VIDEO IN
REMOTE 1 REMOTE 2 IN OUTSERIAL
1
6 78 9 10 11
2 3 45
1 Video input
2 S-Video input
3 RGB 1 input
4 RGB 2 Input
5 DVI-D input
6 LAN connector
7 Remote 1 input
8 Remote 1 output
9 Remote 2 input
10 Serial input
11 Serial output

SPEC FILE
PT-DX800S/DX800K/DX800LS/DX800LK
DLP™Projectors
As of December 2011
SFD11M002-1
5/14
Standard setting-up position
Caution:
• All construction work should be done by a qualified technician.
• When mounting to the ceiling, use the special mounting bracket. To prevent the projector from swaying or drop-
ping, attach the wire between the mounting bracket and the ceiling.
Upper edge of projected image
255
(10-1/32)
168
(6-10/16)
A*1
*2
Lower edge of projected image
Projected image
L
L
L
340–420
(13-3/8–
16-17/32)
416–496
(16-3/8–
19-17/32)
100 (3-15/16)
344
(13-17/32)
100
(3-15/16)
400
(15-3/4)
Projected image
HH
unit : mm (inch)
*1 When the lens protrudes to the maximum.
A: 84 mm (3-5/16˝ ) with the ET-DLE080
43 mm (1-11/16˝ ) with the supplied lens
44 mm (1-23/32˝ ) with the ET-DLE150
45 mm (1-25/32˝ ) with the ET-DLE250
51 mm (2˝ ) with the ET-DLE350
95 mm (3-3/4˝ ) with the ET-DLE450
27 mm (1-1/16˝ ) with the ET-DLE055
*2 Adjustable in 40 mm (1-9/16˝) steps.
NOTE:
Illustrations show the projector installed
using optional ceiling mount bracket
ET-PKD56H and an optional lens.
This illustration is not drawn to scale.

SPEC FI L E
PT-DX800S/DX800K/DX800LS/DX800LK
DLP™Projectors
As of December 2011
SFD11M002-1
6/14
Screen size
(diagonal)
min. max. min. max.
Zoom lens
Distance to screen (L) Height from the edge of screen
to center of lens (H)
min. max. min. max. min. max.
ET-DLE150
min. max.
ET-DLE080 Supplied lens ET-DLE250 ET-DLE350 ET-DLE450 With a zoom
lens except
ET-DLE080
With
ET-DLE080
4
1.27
1.52
1.78
2.03
2.29
2.54
3.05
3.81
5.08
6.35
7.62
10.16
12.70
15.24
[m] [in]
50
60
70
80
90
100
120
150
200
250
300
400
500
600
/
/
/
/
/
/
/
/
/
/
/
/
/
/
–
–
–
–
–
–
–
–
–
–
–
–
–
–
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.38
0.46
0.53
0.61
0.69
0.76
0.91
1.14
1.52
1.91
2.29
3.05
3.81
4.57
–
–
–
–
–
–
–
–
–
–
–
–
–
–
0.04
0.05
0.05
0.06
0.07
0.08
0.09
0.11
0.15
0.19
0.23
0.31
0.38
0.46
0.38
0.46
0.53
0.61
0.69
0.76
0.91
1.14
1.52
1.91
2.29
3.05
3.81
4.57
1.97
2.37
2.77
3.18
3.58
3.98
4.79
6.00
8.02
10.03
12.05
16.08
20.12
24.15
1.01
1.22
1.43
1.64
1.86
2.07
2.49
3.12
4.18
5.23
6.29
8.40
10.51
12.62
2.51
3.03
3.55
4.06
4.58
5.10
6.13
7.68
10.26
12.85
15.43
20.60
25.77
30.94
3.78
4.55
5.32
6.09
6.86
7.63
9.18
11.49
15.34
19.20
23.06
30.77
38.48
46.19
5.68
6.84
8.01
9.17
10.33
11.50
13.82
17.31
23.13
28.94
34.76
46.39
58.02
69.65
8.91
10.75
12.60
14.44
16.28
18.12
21.81
27.33
36.54
45.76
54.97
73.39
91.81
110.23
1.34
1.62
1.90
2.18
2.46
2.74
3.30
4.14
5.54
6.94
8.33
11.13
13.92
16.72
0.81
0.98
1.15
1.32
1.49
1.66
2.00
2.51
3.36
4.21
5.07
6.77
8.48
10.18
1.78
2.15
2.52
2.89
3.26
3.63
4.37
5.48
7.33
9.18
11.03
14.73
18.43
22.13
2.36
2.85
3.34
3.83
4.32
4.80
5.78
7.24
9.69
12.13
14.57
19.45
24.33
29.22
3.71
4.48
5.25
6.02
6.79
7.56
9.10
11.41
15.26
19.11
22.96
30.65
38.35
46.05
5.53
6.69
7.86
9.02
10.19
11.35
13.68
17.18
23.00
28.83
34.66
46.31
57.96
69.61
Screen size
(diagonal)
min. max. min. max.
Zoom lens
Distance to screen (L) Height from the edge of screen
to center of lens (H)
min. max. min. max. min. max.
ET-DLE150
min. max.
ET-DLE080 Supplied lens ET-DLE250 ET-DLE350 ET-DLE450 With a zoom
lens except
ET-DLE080
With
ET-DLE080
4
1.27
1.52
1.78
2.03
2.29
2.54
3.05
3.81
5.08
6.35
7.62
10.16
12.70
15.24
[m] [in]
50
60
70
80
90
100
120
150
200
250
300
400
500
600
/
/
/
/
/
/
/
/
/
/
/
/
/
/
–
–
–
–
–
–
–
–
–
–
–
–
–
–
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
1.3
1.5
1.8
2.0
2.3
2.5
3.0
3.8
5.0
6.3
7.5
10.0
12.5
15.0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
0.1
0.2
0.2
0.2
0.2
0.3
0.3
0.4
0.5
0.6
0.8
1.0
1.3
1.5
1.3
1.5
1.8
2.0
2.3
2.5
3.0
3.8
5.0
6.3
7.5
10.0
12.5
15.0
6.5
7.8
9.1
10.4
11.7
13.1
15.7
19.7
26.3
32.9
39.5
52.8
66.0
79.2
3.3
4.0
4.7
5.4
6.1
6.8
8.2
10.2
13.7
17.2
20.6
27.5
34.5
41.4
8.2
9.9
11.6
13.3
15.0
16.7
20.1
25.2
33.7
42.2
50.6
67.6
84.5
101.5
12.4
14.9
17.5
20.0
22.5
25.0
30.1
37.7
50.3
63.0
75.6
100.9
126.2
151.5
18.6
22.5
26.3
30.1
33.9
37.7
45.4
56.8
75.9
95.0
114.0
152.2
190.4
228.5
29.2
35.3
41.3
47.4
53.4
59.5
71.5
89.7
119.9
150.1
180.3
240.8
301.2
361.7
4.4
5.3
6.2
7.2
8.1
9.0
10.8
13.6
18.2
22.8
27.3
36.5
45.7
54.9
2.6
3.2
3.8
4.3
4.9
5.4
6.6
8.2
11.0
13.8
16.6
22.2
27.8
33.4
5.8
7.0
8.3
9.5
10.7
11.9
14.3
18.0
24.0
30.1
36.2
48.3
60.5
72.6
7.7
9.4
11.0
12.6
14.2
15.8
19.0
23.8
31.8
39.8
47.8
63.8
79.8
95.9
12.2
14.7
17.2
19.8
22.3
24.8
29.9
37.4
50.1
62.7
75.3
100.6
125.8
151.1
18.1
21.9
25.8
29.6
33.4
37.2
44.9
56.4
75.5
94.6
113.7
151.9
190.2
228.4
Projection distance for 4:3 aspect ratio screen
Unit: feet
Unit: meters
• The value for L (distance to screen) varies slightly within ±5% depending on the zoom lens characteristics.
• The zoom lens characteristics may cause slight image distortion.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
• The brightness varies depending on the zoom setting.

SPEC FI L E
PT-DX800S/DX800K/DX800LS/DX800LK
DLP™Projectors
As of December 2011
SFD11M002-1
7/14
1.27
1.52
1.78
2.03
2.29
2.54
3.05
3.81
5.08
/
/
/
/
/
/
/
/
/
50
60
70
80
90
100
120
150
200
Screen size
(diagonal)
ET-DLE055 fixed-focus lens
Distance to screen (L) Height from the edge of
screen to center of lens (H)
[m] [in]
0.38
0.46
0.53
0.61
0.69
0.76
0.91
1.14
1.52
0.81
0.98
1.15
1.32
1.49
1.66
2.01
2.52
3.38
1.27
1.52
1.78
2.03
2.29
2.54
3.05
3.81
5.08
/
/
/
/
/
/
/
/
/
50
60
70
80
90
100
120
150
200
Screen size
(diagonal)
ET-DLE055 fixed-focus lens
Distance to screen (L) Height from the edge of
screen to center of lens (H)
[m] [in]
1.3
1.5
1.8
2.0
2.3
2.5
3.0
3.8
5.0
2.7
3.2
3.8
4.3
4.9
5.5
6.6
8.3
11.1
Projection distance for 4:3 aspect ratio screen
Unit: feetUnit: meters
• The value for L (distance to screen) varies slightly within ±5% depending on the zoom lens characteristics.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
Note: When the ET-DLE055 is mounted, the optical lens shift function cannot be used.
Calculation of the projection distance
For a screen size different from the above, use the equation below to calculate the projection distance.
• Distances calculated with the above equations will include a slight error.
minimum L (m) = (diagonal screen size in inches) × 0.0170 - 0.0471
maximum L (m) = (diagonal screen size in inches) × 0.0211 - 0.0442
minimum L (m) = (diagonal screen size in inches) × 0.0280 - 0.0540
maximum L (m) = (diagonal screen size in inches) × 0.0403 - 0.0498
minimum L (m) = (diagonal screen si e in inches) × 0.0370 - 0.0746
maximum L (m) = (diagonal screen si e in inches) × 0.0517 - 0.0725
minimum L (m) = (diagonal screen size in inches) × 0.0488 - 0.0800
maximum L (m) = (diagonal screen size in inches) × 0.0771 - 0.0792
minimum L (m) = (diagonal screen size in inches) × 0.0770 - 0.1351
maximum L (m) = (diagonal screen size in inches) × 0.1163 - 0.1346
minimum L (m) = (diagonal screen size in inches) × 0.1165 - 0.3017
maximum L (m) = (diagonal screen size in inches) × 0.1842 - 0.2991
(fixed focus) L (m) = (diagonal screen size in inches) × 0.0171 - 0.0476
ET-DLE080
ET-DLE150
Supplied lens
ET-DLE250
ET-DLE350
ET-DLE450
ET-DLE055
Aspect ratio 4:3

SPEC FILE
PT-DX800S/DX800K/DX800LS/DX800LK
DLP™Projectors
As of December 2011
SFD11M002-1
8/14
H
(Width of
projected image)
V
(Height of
projected image)
0.5V
0.1H0.1H
Standard postition
of projected image
H
(Width of
V
(Height of
projected image)
0.5V
0.1H0.1H
Standard postition
of projected image
360°
-15°
+15°
Shift range
Optical axis shift function allows to shift the position of a projected image as shown below.
Installable angle
Install the projector at an angle within the range shown below.
• Vertical direction
The projector may be installed at a vertical
angle of 360°.
• Horizontal direction
The projector may be installed at a horizontal
angle of ±15°.
• Floor mount
(When the lens except the ET-DLE080 is mounted.)
• Ceiling mount
(When the lens except the ET-DLE080 is mounted.)
H
(Width of
projected image)
V
(Height of
projected image)
0.45V
0.34V
0.1H0.1H
Standard postition
of projected image H
(Width of
projected image)
V
(Height of
projected image)
0.45V
0.34V
0.1H0.1H
Standard postition
of projected image
• Floor mount
(When the ET-DLE080 is mounted.)
• Ceiling mount
(When the ET-DLE080 is mounted.)
• The ET-DLE055 has a fixed short-focus lens. Therefore, the lens shift function provided in the main unit cannot be used.

SPEC FI L E
PT-DX800S/DX800K/DX800LS/DX800LK
DLP™Projectors
As of December 2011
SFD11M002-1
9/14
List of compatible signals
The signals that can be input to this projector are shown in the table below. orizontal scanning fre-
quencies of 15 k z to 91 k z, vertical scanning frequencies of 50 z to 85 z, and a dot clock of
150 M z maximum can be input.
NOTE: The native resolution of this projector is 1,024 × 768 pixels. If the display resolution of the input signal is different from the
native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
Display mode Display
resolution
(dots)1
Scanning frequency
H
(kHz)
V
(kHz)
Dot clock
frequency
(MHz)
Picture
quality2Format
720 × 480i
720 × 576i
720 × 480i
720 × 576i
720 × 483
720 × 576
1,280 × 720
1,920 × 1,080i
1,920 × 1,080
1,920 × 1,080i
1,920 × 1,080
640 × 400
640 × 480
800 × 600
832 × 624
1,024 × 768
1,152 × 864
1,152 × 870
1,280 × 768
1,280 × 800
1,280 × 960
1,280 × 1,024
1,400 × 1,050
1,440 × 900
1,600 × 1,200
1,680 × 1,050
1,920 × 1,080
1,920 × 1,200
15.7
15.6
15.7
15.6
31.5
31.3
45.0
37.5
33.8
28.1
27.0
27.0
28.1
33.8
67.5
56.3
31.5
37.9
31.5
35.0
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
49.7
39.6
48.4
56.5
60.0
65.5
68.7
80.0
96.7
64.0
67.5
76.7
68.7
39.6
47.8
41.3
49.7
60.0
64.0
80.0
91.1
64.0
82.2
55.9
75.0
65.3
66.6
74.0
59.9
50.0
59.9
50.0
59.9
50.0
60.0
50.0
60.0
50.0
24.0
24.0
50.0
60.0
60.0
50.0
70.1
85.1
59.9
66.7
72.8
75.0
85.0
56.3
60.3
72.2
75.0
85.1
74.6
50.0
60.0
70.1
75.0
81.6
85.0
100.0
120.0
71.2
74.9
85.0
75.1
49.9
59.9
50.0
59.8
60.0
60.0
75.0
85.0
60.0
75.0
59.9
60.0
60.0
59.9
60.0
−
−
13.5
13.5
27.0
27.0
74.3
74.3
74.3
74.3
74.3
74.3
74.3
74.3
148.5
148.5
25.2
31.5
25.2
30.2
31.5
31.5
36.0
36.0
40.0
50.0
49.5
56.3
57.3
51.9
65.0
75.0
78.8
86.0
94.5
105.0
130.0
94.2
108.0
121.5
100.0
65.3
79.5
68.0
83.5
108.0
108.0
135.0
157.5
108.0
155.9
106.5
162.0
146.3
138.5
154.0
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
AA
AA
AA
AA
AA
AA
AA
AA
A
A
A
A
A
A
A
A
A
A
A
B
A
B
A
B
A
A
A
NTSC/NTSC4.43/PAL-M/PAL60
PAL/PAL-N/SECAM
480i (525i)
576i (625i)
480p (525p)
576p (625p)
720/60p
720/50p
1080/60i
1080/50i
1080/24p
1080/24sF
1080/25p
1080/30p
1080/60p
1080/50p
VGA400
VGA480
SVGA
MAC16
XGA
MXGA
MAC21
1280 × 768
1280 × 800
MSXGA
SXGA
SXGA+
WXGA+
UXGA
WSXGA+
1920 × 10803
WUXGA3
VIDEO/S-VIDEO
YPBPR/RGB
YPBPR/RGB/DVI-D
RGB/DVI-D
1. The “i” appearing after the resolution indicates an interlaced signal.
2. The following symbols are used to indicate picture quality.
AA aximum picture quality can be obtained.
A Signals are converted by the image processing circuit before picture is projected.
B Pixels are thinned (or the image is converted by an image processing circuit for DVI-D signal input) before the picture is projected.
3. Compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).

SPEC FI L E
PT-DX800S/DX800K/DX800LS/DX800LK
DLP™Projectors
As of December 2011
SFD11M002-1
10/14
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, com-
mands must be input through communication software, based on the format and satisfying the commu-
nication conditions shown below.
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent
in this order. Add parameters according to the details of control.
Communication conditions (factory setting)
Pin assignments and signal names
6
15
9
D-sub 9-pin (female) Serial input
Description
NC
Send data
Receive data
Connected internally
Ground
Signal name
–
TXD
RXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
CTS
RTS
–
No.
6
7
8
9
Pin assignments and signal names
9
51
6
D-sub 9-pin (male) Serial output
Description
NC
Receive data
Send data
Connected internally
Ground
Signal name
–
RXD
TXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
RTS
CTS
–
No.
6
7
8
9
CAUTION
• It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this
occurs, wait for 60 seconds, then try sending or receiving again.
• When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before
sending the next command.
• Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for com-
mand response to 10 seconds or more.
• When using two or more units:
1) Set different IDs for each unit.
2) Designate only one unit as RESPONSE (ID ALL) ON and the rest as RESPONSE (ID ALL) OFF.
3) Each group should have only one RESPONSE (ID GROUP) ON and the rest should be RESPONSE (ID GROUP) OFF.
Start
(1 byte)
End
(1 byte)
Colon
(1 byte)
Semicolon
(1 byte)
(2 byte)
ID designator
01 to 64: Address number
0A to 0Z: Group ID
ZZ: All units (ID ALL)
ID: 2 characters
(2 bytes) Parameters
(undefined length)
Command
(3 bytes)
(Control and/or query commands)
STX ETXC1P1P2...PnC2ADI1I2 C3:;
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
X parameter
S parameter
RS-232C-compliant
Start-stop synchronization
9,600 bps
None
8 bits
1 bit
None
None

SPEC FI L E
PT-DX800S/DX800K/DX800LS/DX800LK
DLP™Projectors
As of December 2011
SFD11M002-1
11/14
Control commands
Command : Parameter Function Callback
PON
POF
IIS:DVI
IIS:RG1
IIS:RG2
IIS:VID
IIS:SVD
LPM:0
LPM:1
LPM:2
LPM:3
OSH:0
OSH:1
OFZ:0
OFZ:1
OAS
VPM:NAT
VPM:STD
VPM:DYN
VPM:CIN
VPM:GRA
VXX:DLVI0=+00000
VXX:DLVI0=+00001
VXX:DLVI0=+00002
VXX:DLVI0=+00003
OTE:1
OTE:2
OTE:4
OTE:10
TSD:y1y2y3y4m1m2d1d2w
TST:h1h2m1m2s1s2
OOS:0
OOS:1
POWER (STANDBY)
INPUT SELECT
LAMP SELECT
SHUTTER
FREEZE
AUTO SETUP
PICTURE MODE
SYSTEM DAYLIGHT VIEW 2
COLOR TEMPERATURE
DATE
TIME
ON SCREEN
PON
POF
IIS:DVI
IIS:RG1
IIS:RG2
IIS:VID
IIS:SVD
LPM:0
LPM:1
LPM:2
LPM:3
OSH:0
OSH:1
OFZ:0
OFZ:1
OAS
VPM:NAT
VPM:STD
VPM:DYN
VPM:CIN
VPM:GRA
VXX:DLVI0=+00000
VXX:DLVI0=+00001
VXX:DLVI0=+00002
VXX:DLVI0=+00003
OTE:1
OTE:2
OTE:4
OTE:10
TSD:y1y2y3y4m1m2d1d2w
TST:h1h2m1m2s1s2
OOS:0
OOS:1
Standby power on
Standby power off
DVI-D
RGB 1
RGB 2
Video
S-Video
Dual (two lamps)
Single lamp
Lamp 1
Lamp 2
Shutter on
Shutter off
Off
On
Natural
Standard
Dynamic
Cinema
Graphic
Off
1
2
3
Middle
High
User
Default
Date setting
Time setting
On-screen display off
On-screen display on
Cable specifications
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
PC (DTE)Projector
NC
NC
NC
NC
NC
NC
NC
NC
* Do not send PON, POF or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement
cycle.
* When a command that cannot be executed during standby mode is sent, the projector will send an ER401 command in reply.

SPEC FI L E
PT-DX800S/DX800K/DX800LS/DX800LK
DLP™Projectors
As of December 2011
SFD11M002-1
12/14
Status request commands
Command example
To set the on-screen display off, send the command as shown below.
ADZZ OOS :0; ETX
ID Address Command
STX
Start Parameter End
NOTE: When sending commands without parameters, a colon (:) is not necessary.
Command:Parameter Function DescriptionCallback
QPW
QSH
QFZ
QIN
QOS
QST
Q$L:1
Q$L:2
QSL
QLP
QPM
QVX:DLVI0
QTM:0
QTM:1
QTM:2
QGD
QGT
Main power status
Shutter function status
Freeze function status
Input signal status
On-screen display status
Projector run time
Lamp 1 run time
Lamp 2 run time
Lamp operation mode status
Lamp power mode status
Picture mode status
System daylight view status
Temperature status
Date setting status
Time setting status
Standby (Off)
On
Off
On
Off
On
DVI-D
RGB 1
RGB 2
Video
S-Video
Off
On
00000h–99999h
0000h–9999h
0000h–9999h
Dual
Single
Lamp 1
Lamp 2
High
Low
Natural
Standard
dynamic
Cinema
Graphic
Off
1
2
3
p0 = Intake air
p1 = Exhaust air
p2 = DLP™ chip
yyyymmdd (day of week) (*2)
hhmmss
000
001
0
1
0
1
DVI
RG1
RG2
VID
SVD
0
1
p1p2p3p4p5
p1p2p3p4
p1p2p3p4
0
1
2
3
0
1
NAT
STD
DYN
CIN
GRA
DLVI0=+00000
DLVI0=+00001
DLVI0=+00002
DLVI0=+00003
p1p2p3p4/p5p6p7p8 (*1)
y1y2y3y4m1m2d1d2w
h1h2m1m2s1s2
*2Day of week: Monday = 1, Tuesday = 2, ... Sunday = 7
*1p1p2p3p4: Celsius (°C), p5p6p7p8: Fahrenheit (°F)
NOTE: If a wrong command is received, the projector will send an ER401 or ER402 command to the computer.

SPEC FI L E
PT-DX800S/DX800K/DX800LS/DX800LK
DLP™Projectors
As of December 2011
SFD11M002-1
13/14
Notes on projector placement and operation
The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the
following precautions.
1. Never place objects on top of the projector.
2. Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector’s
exhaust openings.
3. Do not stack projector units directly on top of one another for the purpose of multiple (stacked)
projection. When stacking projector units, be sure to provide the amount of space indicated below
between them. These space requirements also apply to installations where only one projector unit
is operating at one time and the other unit is used as a backup.
4. Make sure that nothing blocks the projector’s air intake and exhaust openings. Also, install the pro-
jector so that cool or hot air from other air conditioning equipment does not flow directly toward
the projector’s air intake or exhaust openings.
5. Do not install the projector in an enclosed space. If it is necessary to install it in an enclosed
space, add a separate ventilation system. If ventilation is insufficient, hot air will accumulate at the
intake opening. This may cause the projector’s protective circuit to interrupt projector operation.
6. If the projector is installed in an enclosed space, ensure that the projector’s intake and exhaust
openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is
not sucked into the intake openings.
7. When installing the projector in any manner other than floor mounting with the adjuster legs, use
the five threaded ceiling mount holes (screw diameter: M6, projector interior thread length: 12 mm)
to secure the projector.
500 mm (19-11/16˝ ) or more
500 mm (19-11/16˝ )
or more
500 mm (19-11/16˝ )
or more
Do not stack projector
units directly on top of
one another.
100 mm
(3-15/16˝)
or more
Direction of air intake and exhaust
Intake
Exhaust

SPEC FI L E
PT-DX800S/DX800K/DX800LS/DX800LK
DLP™Projectors
As of December 2011
SFD11M002-1
14/14
Operating the projector continuously
1. If the projector is to be operated continuously for 24 hours, use the dual-lamp optical system's alternat-
ing lamp operation (lamp relay) function. Continuously operating the projector for 24 hours in the dual-
lamp mode is not recommended. Allow a minimum of two hours per day of non-operation time for each
lamp if the projector is to be operated continuously for more than 22 hours.
2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short
periods.
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
Product availability differs depending on region and country. This product may be subject to export control regulations.
DLP and the DLP logo are trademarks of Texas Instruments.
PJLink is a registered trademark, or a trademark application has been filed, in Japan, the United States, and other countries and regions.
All other trademarks are the property of their respective trademark owners.