Panasonic WX-CR480P User manual

Before attempting to connect or operate this product, please read these instructions
carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
WX-CR480
STATUS ID REG
Operating Instructions
Included Installation Instructions
Wireless Repeater
Model No. WX-CR480P
ENGLISHFRANÇAIS
PUQX1029ZA
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 1 2021/11/08 13:25:12

2
Safety precautions
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna
or transmitter.
This equipment complies with FCC/ISED radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines
in Supplement C to OET65 and RSS-102 of the ISED radio frequency (RF) Exposure
rules. This equipment should be installed and operated keeping the radiator at least
20 cm or more away from person’s body (excluding extremities: hands, wrists, feet and
ankles).
This device complies with Part 15 of FCC Rules and ISED licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of this device.
WARNING:
• To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture.
• The apparatus should not be exposed to dripping or splashing and no objects filled
with liquids, such as vases, should be placed on the apparatus.
• To prevent injury, this apparatus must be securely attached to the wall in accordance
with the installation instructions.
• The installation shall be carried out in accordance with all applicable installation rules.
• This product has no power switch.
When turning off the power, disconnect the power supply from the USB device.
• Operating near 1.9 GHz electrical appliances may cause interference. Move away from
the electrical appliances.
• This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter.
• MEDICAL:
Consult the manufacturer of any personal medical devices, such as pacemakers, to
determine if they are adequately shielded from external RF (radio frequency) energy.
(The unit operates in the frequency range of 1.92 GHz to 1.93 GHz, and the power
output level is 115mW (max.)
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 2 2021/11/08 13:25:12

3
ENGLISH
Supplier’s Declaration of
conformity
Trade Name: Panasonic
Model No.: WX-CR480P
Responsible Party:
Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ
07102-5490
Support Contact: 1-800-491-9986
[email protected]
For U.S.A.
FCC Caution:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
For U.S.A.
NOTE: This equipment has been tested
and found to comply with the limits for a
Class A digital device, pursuant to part 15
of the FCC Rules. These limits are
designed to provide reasonable protection
against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates,
uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instruction manual,
may cause harmful interference to radio
communications. Operation of this
equipment in a residential area is likely to
cause harmful interference in which case
the user will be required to correct the
interference at his own expense.
For U.S.A.
The model number and serial number of
this product may be found on the surface
of the unit.
You should note the model number and
serial number of this unit in the space
provided and retain this book as a
permanent record of your purchase to aid
identification in the event of theft.
Model No. ________________________
Serial No. ________________________
For U.S.A.
CAUTION:
The FCC ID number for this radio
equipment is listed below.
FCC ID: ACJ9TAWX-CR480P.
For U.S.A.
Descriptions of graphic symbols
This symbol indicates an direct
current (DC).
CAUTION:
• A READILY ACCESSIBLE
DISCONNECT DEVICE SHALL BE
INCORPORATED TO THE
EQUIPMENT POWERED BY DC5 V
POWER SUPPLY.
• These servicing instructions are for use
by qualified service personnel only. To
reduce the risk of electric shock do not
perform any servicing other than that
contained in the operating instructions
unless you are qualified to do so.
• Shielded (STP) LAN cables must be
used with this unit to ensure
compliance with EMC standards.
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 3 2021/11/08 13:25:13

4
Safety precautions
RSS-Gen
• This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
For Canada
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
8) Only use attachments/accessories specified by the manufacturer.
9) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
10) To prevent it from falling, remove the product without leaving it at the end of use.
CAN ICES-003(A)/NMB-003(A)
For Canada
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 4 2021/11/08 13:25:13

5
ENGLISH
Table of contents
Safety precautions……………………………………………………………………………… 2
Before use ……………………………………………………………………………………… 6
Product overview ………………………………………………………………………………………6
System overview ………………………………………………………………………………………6
Limitation of liability ……………………………………………………………………………………9
Disclaimer of Warranty ………………………………………………………………………………9
Copyright …………………………………………………………………………………………… 10
Abbreviations ……………………………………………………………………………………… 10
Precautions ……………………………………………………………………………………… 11
Usage precautions……………………………………………………………………………… 13
Parts and their names ………………………………………………………………………… 14
Installation ……………………………………………………………………………………… 16
Installation precautions …………………………………………………………………………… 16
Repeater installation procedure…………………………………………………………………… 19
Wall installation (with fixing bracket) ……………………………………………………………… 21
Connections …………………………………………………………………………………… 24
Connecting a power supply ……………………………………………………………………… 24
Registering IDs to the center module …………………………………………………………… 25
Dimensions ……………………………………………………………………………………… 27
Troubleshooting ………………………………………………………………………………… 28
Specifications …………………………………………………………………………………… 29
Standard accessories ……………………………………………………………………………… 30
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 5 2021/11/08 13:25:13

6
Product overview
This product is a wireless repeater to be used with an All-In-One Headset (WX-CH450/
WX-CH455/WX-CH457P: sold separately) and a Belt Pack (WX-CT420: sold separately).
It connects to a Center Module (WX-CC411BP/WX-CC412BP: sold separately) to function.
●It uses a system based on the 1.9 GHz DECT* standard to achieve a stable connection
over a wide area which makes for a clear audio with little interference.
* DECT (Digital Enhanced Cordless Telecommunications) is a digital cordless
communication standard.
●Installation is easy and can be performed on a wall.
●A USB power adaptor and USB cable are not included. Purchase commercially available
products.
System overview
A repeater is used when you need to extend the range of an All-In-One Headset or a Belt
Pack to include areas where reception was previously not available.
Two repeaters can be registered to one lane of a center module.
In the case of a single lane center module (WX-CC411BP), two repeaters can be
registered to the center module.
In the case of a dual lane center module (WX-CC412BP), one repeater can be registered
each for lane A and lane B, or two repeaters can be registered in either lane A or lane B.
System connection example
Repeater is installed within the coverage area of the center module.
2 repeaters can be connected to lane A or lane B.
Lane A
Center module
All-In-One
Headset
WX-CR480
STATUS IDREG
Repeater
All-In-One
Headset
WX-CR480
STATUS IDREG
Repeater
Configuration of
connected devices
Before use
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 6 2021/11/08 13:25:13

7
ENGLISH
When a repeater is to be connected to each of lane A and lane B, 1 repeater can be
connected to each lane.
All-In-One
Headset
WX-CR480
STATUS IDREG
Repeater
All-In-One
Headset
WX-CR480
STATUS IDREG
Repeater
Lane A
Lane B
Center module
Configuration of
connected devices
Concerning the extension in coverage area
Coverage area can be extended by using a repeater.
A maximum of 2 repeaters can be registered per each center module.
One repeater can be registered each for lane A and lane B, or two repeaters can be
registered in either lane A or lane B. (only WX-CC412BP)
- When two repeaters are registered in lane A, cannot be registered in lane B.
- When two repeaters are registered in lane B, cannot be registered in lane A.
With just the center module
Within range Out of range
Coverage area
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 7 2021/11/08 13:25:13

8
Before use
1 repeater registered in lane A (lane B)
WX-CR480
STATUS IDREG
Within range
Coverage area
2 repeaters registered in lane A (lane B)
WX-CR480
STATUS IDREG
WX-CR480
STATUS IDREG
Within range
Within range
Coverage area
●Repeaters cannot be connected in a cascade arrangement.
WX-CR480
STATUS IDREG
Center module All-In-One
Headset
Repeater
WX-CR480
STATUS IDREG
Repeater
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 8 2021/11/08 13:25:14

9
ENGLISH
Limitation of liability
THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE,
OR NON-INFRINGEMENT OF THE THIRD PARTY’S RIGHT. THIS PUBLICATION COULD
INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. CHANGES
ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE
IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING
PRODUCT(S).
Disclaimer of Warranty
IN NO EVENT SHALL Panasonic Corporation BE LIABLE TO ANY PARTY OR ANY
PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE
PRODUCT, FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:
A
ANY LOSS OR DAMAGE, INCLUDING WITHOUT LIMITATION, DIRECT OR
INDIRECT, SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR
RELATING TO THE PRODUCT;
B
ANY INCONVENIENCE, LOSS, OR DAMAGE CAUSED BY INAPPROPRIATE USE OR
NEGLIGENT OPERATION OF THE USER;
C
ALL MALFUNCTIONS OR TROUBLES FROM UNAUTHORIZED DISASSEMBLY,
REPAIR OR MODIFICATION OF THE PRODUCT BY THE USER, REGARDLESS OF
THE CAUSE OF THE MALFUNCTION OR TROUBLE;
D
ANY PROBLEM CAUSING FAILED SIGNAL TRANSMISSION RESULTING IN
CONSEQUENTIAL INCONVENIENCE, LOSS OR DAMAGE, ARISING OUT OF
CAUSES SUCH AS SYSTEM MALFUNCTION, FAULT, SET UP OR INSTALLATION.
E
ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE,
ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY.
F
IMPOSSIBILITY TO USE THE PRODUCT OR ANY INCONVENIENCE, LOSS, OR
DAMAGE ARISING OUT OF THE IMPOSSIBILITY TO USE THE PRODUCT BECAUSE
OF RADIO WAVES BROADCAST BY THIRD PARTIES.
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 9 2021/11/08 13:25:14

10
Before use
Copyright
Distributing, copying, disassembling, reverse compiling and reverse engineering of the
software provided with this product are all expressly prohibited. In addition, exporting any
software provided with this product violating export laws is prohibited.
Abbreviations
This manual uses the following abbreviations.
●“Wireless Repeater (WX-CR480P)” is referred to as “this product” or “repeater”.
●“Center Module (WX-CC411BP/WX-CC412BP: sold separately)” is referred to as “center
module”.
●“All-In-One Headset (WX-CH450/WX-CH455/WX-CH457P: sold separately)” is referred
to as “All-In-One Headset”.
●“Belt Pack (WX-CT420: sold separately)” is referred to as “Belt Pack”.
All information on separately-sold products contained in this manual is up-to-date as of
April 2022. Refer to a retailer for the latest information.
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 10 2021/11/08 13:25:14

11
ENGLISH
Precautions
Tighten screws and bolts with the specified tools
Failing to do so may cause parts to fall leading to accidents and injuries.
Install the product so that its weight is properly supported
Failing to do so may cause the repeater to fall leading to accidents and injuries.
●Make sure that your chosen installation method offers enough support before installing
the repeater.
Properly install the repeater to a wall according to the installation
directions.
Failing to do so may lead to accidents and injuries.
If the product shows any abnormality, immediately stop using it
If the product shows abnormalities such as smoke or an unusual smell coming out of the
product, or damage to its outer shell, continuing to use it may pose hazards such as the
product catching on fire or falling, leading to injuries to the users or to further damage to
the product itself.
●Immediately turn the product OFF and contact the retailer.
If the outer shell of the product shows cracks or other damage, immediately
suspend use and take it down
Failing to do so may cause the product to fall.
●Always ask a retailer to do this.
When the product is no longer needed or can no longer be used, do not
leave it unattended and take it down
Failing to do so may lead to the corrosion of some components which could cause the
product to fall.
●Always ask a retailer to do this.
Always inspect the product after an earthquake
The mounting unit could be damaged, causing the product to fall.
●Always ask a retailer to do this.
Do not bring the product near medical equipment
(do not bring it near operation rooms, ICUs, CCUs, etc.)
The radio waves emitted from the product may interfere with the medical equipment
causing it to malfunction and lead to accidents.
Do not use near automatic doors, fire alarms, and other automatic
controllers
The radio waves emitted from the product may interfere with the automatic controllers
causing them to malfunction and lead to accidents.
Do not use near flammable gases
Doing so may lead to explosions and injuries.
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 11 2021/11/08 13:25:14

12
Precautions
Do not install the product where there is a risk of damage from seawater or
corrosive gases
This may cause the mounting unit to deteriorate, leading to accidents and injuries.
Do not let foreign substances into the product
Water or metals entering the repeater may lead to fires or electric shocks.
●Immediately turn the product OFF and contact the retailer.
Do not replace parts while the product is installed
This may cause parts to fall leading to accidents.
Do not install the product if the fixing bracket is deformed or the outer shell
is damaged
This may cause parts to fall leading to accidents.
Do not attempt to disassemble or remodel the product
It may lead to fire or electric shock.
Entrust installation operations to a retailer
The installation operations needed to install this product require skill and experience. They
involve a risk of injury to people and damage to things.
●Always ask a retailer to do this.
Entrust work in high places to a certified professional
Working in high places requires skill and experience. It involves a risk of injury to people
and damage to things.
●Always ask a retailer to do this.
Turn the product OFF before performing maintenance
It may lead to injury.
Do not attempt to repair or wire the product while it is turned ON
It may lead to injury.
Do not pull on cables and other components
It may lead to injury.
Do not damage the cables
Placing heavy objects on the cables or squeezing them in tight places will damage them,
which could cause injuries.
Do not install in places exposed to large amount of humidity and/or dust
It may lead to injury.
Do not perform the installation and wiring work during a thunderstorm
It may lead to fire or electric shock.
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 12 2021/11/08 13:25:14

13
ENGLISH
Other than the aforementioned “Precautions”, make sure to follow the points below.
Use this product with care
●This product contains delicate components which may be damaged by improper use or storage.
●Repair or replace any damaged components.
The operating temperature range is
●Between 0 °C (32 °F) and +40 °C (104 °F). Using the product outside of this range may
cause it to malfunction or to be damaged.
Power
●The repeater does not have a power switch. Unplug the USB cable (page 18) to turn
OFF the repeater.
Interception
●This product uses a difficult to intercept digital signal, but, as it uses radio waves, it
might be possible for a third party to willfully intercept the transmission of the product.
Written specifications
Specifications about the identification, powering, etc. of the repeater are written on the rear
of the repeater.
Maintenance
●Turn OFF the power and clean the product with a dry cloth.
●Do not use volatile chemicals such as benzene or paint thinner.
●Do not use spray-on cleaning solutions, water hoses, high-pressure water cleaning,
steam cleaning, or other potentially damaging cleaning measures.
●When using chemically treated cloths, carefully read the included instructions.
When not using for an extended period of time
●When you are not using the product, always ask a retailer to dismount it.
Usage precautions
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 13 2021/11/08 13:25:14

14
Parts and their names
WX-CR480
STATUS ID REG
SideFront Rear
Side
A B DC
G H
E F
D
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 14 2021/11/08 13:25:14

15
ENGLISH
AStatus indicator [STATUS]
Shows the operation status of the repeater.
On (orange): Connected to lane A, strong signal
On (green): Connected to lane B, strong signal
Slow Blinking (orange): Connected to lane A, weak signal
Slow Blinking (green): Connected to lane B, weak signal
Blinking (orange): Currently registering ID to lane A or searching for lane A
Blinking (green): Currently registering ID to lane B or searching for lane B
On (red): No ID registered
Blinking (red): ID registration failed
Off: No power supply
memo
Important
●Refer to the center module operating instructions for details on ID
registration.
BRegistration button [ID REG]
Press and hold the button to switch to ID registration mode.
Lane A: Indicator is blinking orange
Lane B: Indicator is blinking green
CScrew cover
Used to install the repeater on a wall. Open this screw cover and tighten the screw
inside it to fix the repeater to the fixing bracket.
DHook grooves
Used to install the repeater on a wall. Attach these grooves to the hooks on the fixing
bracket.
ECable routing groove
Pass the USB cable (page 18) through this groove to fix it into place.
FCable tie hook
Pass the included cable tie through this hook to secure the cable.
GPower supply connector
Used to connect the repeater to USB power adaptor. Use a USB cable for the connection.
HMaintenance connector
Used only when maintenance is required.
memo
Important
●Do not connect any PoE devices (hubs or routers equipped with PoE)
to maintenance connector. Doing so may cause malfunctions.
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 15 2021/11/08 13:25:14

16
Installation
■Installation precautions
Warning
●Always ask a retailer to perform these operations.
●Turn off the repeater before installation. Carefully read the
“Precautions” chapter and follow all of its instructions. Also
refer to the manual of the devices you are connecting.
●In order to avoid damages, properly install the repeater
to a wall according to the instructions in this manual.
When installing the repeater, follow all official ordinances on electrical equipment
technical standards.
Do not power ON the repeater while installing it.
●Make sure that the repeater is powered OFF while installing it.
Installation
●Do not use for extended periods of time in very hot or humid environments. The unit will
degrade more quickly and its expected lifespan will be reduced. Improve heat dissipation
near the installation place and make sure that the unit is not hit by direct sunlight.
Installation place
●Install the unit within a range where it can communicate with the center module.
●When placed between the center module and the repeater, devices such as displays or
projectors may cause interference and result in audio dropouts. Make sure that the
repeater has line-of-sight access to the center module.
●Place the repeater at as high a place as possible. Otherwise, people passing across the
low line-of-sight between the repeater and the center module may cause interferences
or audio dropouts.
●This system uses the same frequency (1.9 GHz) as other devices which use the DECT
standard, such as cordless phones. Using this system on the same floor as a cordless
phone or other DECT device may cause interferences and stuttering transmission.
●Using this system in an environment surrounded by metal (copper, aluminum, iron, etc.)
walls, floor, or ceiling may cause the radio waves to be excessively reflected, resulting in a
phenomenon known as “multipath fading”. Multipath fading can cause transmission errors
(such as audio dropouts) even if the signal is strong enough.
●Make sure that there are no objects such as concrete walls or metal panels (partitions,
wall-mounted lockers, doors, etc.) between the repeater and the center module, as
these will obstruct the transmission of radio waves.
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 16 2021/11/08 13:25:14

17
ENGLISH
memo
Important
●Placing the repeater at a low place could reduce its range.
Do not install the repeater in the following places
●Places subject to vibration or strong shocks
●Places exposed to large amounts of humidity and/or dust
●Places where chemicals are being used, such as pools
●Places with large amounts of steam or grease, such as kitchens
●Near speakers, TVs, magnets, and other strong magnetic sources
●Behind (from the repeater’s perspective) display, projectors, etc.
●Near sources of radiation, X-rays, or strong radio waves or magnetism
●Inside metal casings (metal racks containing devices) or rooms whose ceiling or walls
are surrounded by metal
●Near TVs, radios, computers, and other office automation appliances
●Near CS digital broadcasting receivers (tuners, digital TV sets with internal tuners,
recorders, etc.)
●Inside wagon trolleys surrounded by metal
●Where there is a risk of damage from seawater or corrosive gases
●Under direct sunlight
●Places without roofs, directly exposed to the wind and rain
Do not install repeaters close to each other as this can cause noise.
WX-CR480
STATUS IDREG
WX-CR480
STATUS IDREG
Center module
Lane B
Repeater
All-In-One
Headset
All-In-One
Headset
Repeater
If the repeaters are too near,
noise will be generated.
Lane A
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 17 2021/11/08 13:25:15

18
Installation
Wireless interference
●Devices emitting strong radio noise may interfere with the repeater and make it unusable
when placed near it.
Ensure there is enough space between the repeater and such devices to avoid
interference.
(Note: Place the repeater at least 30 m (98.4 ft) away from cellular base stations)
●In the following case, contact a retailer beforehand to confirm suitability of the
environment for use with the repeater:
• Using the repeater on a wagon trolley
●As the repeater uses the same frequency (1.9 GHz) as other DECT devices such as
cordless phones, the maximum number of usable All-In-One Headsets and Belt Packs
may be limited.
Power
●The repeater does not have a power switch. Unplug the USB cable to turn OFF the
repeater. If the cable cannot easily be unplugged because of the way in which the
repeater is installed, unplug the USB power adaptor connected to the repeater.
Static electricity
●Before installing the repeater, discharge yourself by touching a grounded metal object in
order to avoid damage caused by static electricity buildup.
Tightening screws
●Tighten screws straight up. After tightening the screws, make visual confirmation that
they are straight and well-tightened.
●Do not use impact screwdrivers or electric screwdrivers, as even the ones with clutches
make it difficult to control the torque, and risk damaging the mounting unit.
Avoid subjecting the repeater to shocks
●Protect the repeater from strong hits or shocks. These may cause damage to the
repeater.
USB cable
●USB cable is not included with the repeater.
Use a USB cable with a supply current of 1 A or more. There is a maximum cable length
depending on the connection method. See “Connections” (page 24) for details.
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 18 2021/11/08 13:25:15

19
ENGLISH
■Repeater installation procedure
Before installing the repeater, for its optimal use, follow the steps below to temporarily
install it in advance and ensure that the area where it is needed is covered.
1 Advance preparation
Register all of the All-In-One Headsets or Belt Packs and repeaters to the center
module. (page 25)
2 Check the connection with the center module
Temporarily install the repeater and supply power to the repeater with the USB power
adaptor (commercially available).
The repeater connects to the center module after turning on the power.
Check the lighting status of the [STATUS] indicator on the repeater.
●If the [STATUS] indicator on the repeater is orange or green, there is sufficient signal
strength and the location is suitable for installation.
●If the [STATUS] indicator on the repeater is blinking orange or green, the location
needs to be adjusted for installation.
Move the repeater to a location where the [STATUS] indicator on the repeater
changes to solid orange or green.
Unplug the USB power adaptor to stop the power supply, move the installation
location of the repeater closer to the center module, then supply power again from
the USB power adaptor.
Check whether the [STATUS] indicator on the repeater is orange or green.
3 Check the connections with the All-In-One Headsets or Belt Packs
Check whether the All-In-One Headsets or Belt Packs are able to be used in the range
anticipated by the user within the coverage area of the repeater.
4 Install using the repeater fixing bracket (page 21)
Once the connections with the center module and All-In-One Headsets or Belt Packs
have been confirmed, mount the repeater using the repeater fixing bracket.
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 19 2021/11/08 13:25:15

20
Installation
memo
Important
●The range within which the repeater and All-In-One Headsets or Belt Packs
can be used depends on the surrounding environment.
●Signal attenuation
If the repeater is installed inside and is used to communicate with All-In-One
Headsets or Belt Packs that are outside, the signal is attenuated by the wall
material and this may make the distance shorter.
* The signal coverage range is affected by factors related to the installation
environment, such as the structure and materials of the building, so check
the range in advance by temporarily installing the repeater.
WX-CR480P_PUQX1029ZAV1_OI_en-fr.indb 20 2021/11/08 13:25:15