Panasonic WV-CF634 User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
This illustration represents WV-CF624.
Installation Guide
Color CCTV Camera
Model No: WV-CF634
WV-CF624

2
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
WARNING:
•To prevent fire or electric shock hazard, do not
expose this apparatus to rain or moisture.
•Theapparatusshouldnotbeexposedtodrippingor
splashing and that no objects filled with liquids, such
as vases, should be placed on the apparatus.
•All work related to the installation of this product
should be made by qualified service personnel or
system installers.
•To prevent injury, this apparatus must be securely
attached to the floor/wall/ceiling in accordance with
the installation instructions.
•The installation shall be carried out in accordance
with all applicable installation rules.
•Thisproducthasnopowerswitch.
When turning off the power, turn off a Power Supply
or remove a power cable.
•Theconnectionsshouldcomplywithlocalelectrical
code.
This Class A digital apparatus complies with
Canadian ICES-003.
The model number and serial number of this
product may be found on the surface of the unit.
You should note the model number and serial
number of this unit in the space provided and
retainthisbookasapermanentrecordofyour
purchase to aid identification in the event of theft.
Model No.
Serial No.
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is
likelytocauseharmfulinterferenceinwhichcase
the user will be required to correct the interference
at his own expense.
FCC Caution: To assure continued compliance,
(example - use only shielded interface cables
when connecting to computer or peripheral
devices). Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate this equipment.
The lightning flash with arrowhead
symbol, within an equilateral trian-
gle, is intended to alert the user to
the presence of uninsulated "dan-
gerous voltage" within the prod-
uct's enclosure that may be of suf-
ficient magnitude to constitute a
riskofelectricshocktopersons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and mainte-
nance (servicing) instructions in the
literature accompanying the appli-
ance.
For Canada
For U.S.A
For U.S.A

3
Important safety instructions........................................................................................................... 4
Limitation of liability......................................................................................................................... 5
Disclaimer of warranty .................................................................................................................... 5
Preface........................................................................................................................................... 6
About notations ............................................................................................................................. 6
Features ........................................................................................................................................ 6
About the user manuals.................................................................................................................. 7
Trademarksandregisteredtrademarks........................................................................................... 7
Precautions .................................................................................................................................... 8
Precautions for installation ............................................................................................................ 10
Major operating controls and their functions ................................................................................. 12
Preparations ................................................................................................................................. 13
Remove the dome cover............................................................................................................ 13
About the side cable access hole .............................................................................................. 14
Installation method of camera .................................................................................................... 14
Connections............................................................................................................................... 15
Installation ................................................................................................................................... 17
Adjustment................................................................................................................................... 18
Attaching the dome cover............................................................................................................. 22
Setup menu.................................................................................................................................. 24
List of setup menu ..................................................................................................................... 24
Basic operation ............................................................................................................................ 25
Screen transition diagram
CF634
................................................................................................. 27
Screen transition diagram
CF624
................................................................................................. 28
Troubleshooting ........................................................................................................................... 29
Specifications .............................................................................................................................. 30
Standard accessories .................................................................................................................. 31
Contents

4
Important safety instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
 7) Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
 9) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
10) Only use attachments/accessories specified by the manufacturer.
11) Useonlywiththecart,stand,tripod,bracket,ortablespecifiedbythemanufacturer,orsold
with the apparatus. When a cart is used, use caution when moving the cart/ apparatus
combination to avoid injury from tip-over.
12) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
S3125A

5
Limitation of liability
THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF
THE THIRD PARTY'S RIGHT.
THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL
ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE
IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
Disclaimer of warranty
INNOEVENTSHALLPanasonicSystemNetworksCo.,Ltd.BELIABLETOANYPARTYORANY
PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT,
FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:
(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT,
SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE
PRODUCT;
(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT
OPERATION OF THE USER;
(3) UNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION OF THE PRODUCT BY THE
USER;
(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO
ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING
OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;
(6) ANY CLAIM OR ACTION FOR DAMAGES, BROUGHT BY ANY PERSON OR ORGANIZATION
BEING A PHOTOGENIC SUBJECT, DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF
THAT SURVEILLANCE-CAMERA'S PICTURE, INCLUDING SAVED DATA, FOR SOME
REASON, BECOMES PUBLIC OR IS USED FOR ANY PURPOSE.

6
Preface
About notations
Features
Introduction of newly developed high-resolution CCD
TheintroductionofthenewlydevelopedCCDwith976horizontalpixelshasledtoahorizontalres-
olution of as high as 650 TV lines.
Super Dynamic 6 (SUPER-D6)
For photographic subjects which contain high contrast between the bright and dark areas, light
compensationonthepixellevelwillresultinmorenatural-lookingimages.
High sensitivity achieved because of noise reduction function
Sensitivity at the following minimum illuminations has been accomplished for color images because
of the introduction of low noise circuit design (Lens (built-in): F1.3):
0.08lx(color),0.008lx(black-and-white)
Day/Night conversion function equipped
No setup change is required at night because the image automatically changes from the color
mode to the black-and-white mode at low illuminance. Bright images can be captured even at
night because of automatic switching of IR filters at low illuminance.
Focus adjustment function equipped CF634
Auto focus is achieved at installation of the camera or through menu operation.
Motion detection function (VMD) equipped
The motion of an object is detectable. The acts of covering the camera with a cloth, a cap or other
acts and changing the camera direction during surveillance can be detected.
Note:
 •
The VMD function is not the dedicated function to prevent thefts, fires, etc. We are not responsible
for any accidents or damages caused by applying the function for the above purposes.
The following notations are used when describing the functions limited for specific models. The
functions without the notations are supported by all models.
CF634 : The functions with this notation are available when using the model WV-CF634.
CF624 : The functions with this notation are available when using the model WV-CF624.
This product is a 1/3-type CCD color CCTV camera. Connection of this product to a video monitor
allows users to use this product as a monitoring camera.
•
WV-CF634:withcolor/black-and-whitemodeswitchfunctionandbackfocusadjustmentfunction
• WV-CF624:withcolor/black-and-whitemodeswitchfunction

7
About the user manuals
The operating instructions of the camera consist of 2 sets: this book and operating instructions
(PDF).
Thisbookexplainshowtoinstallthecamera.
Refer to the "Operation Instructions (PDF)" on the provided CD-ROM for descriptions of how to
perform the unit settings. Adobe®Reader®is required to read PDF. When the Adobe®Reader®
is not installed on the PC, download the latest Adobe®Reader®from the Adobe web site and
install it.
Trademarks and registered trademarks
Adobe, Acrobat Reader and Reader are either registered trademarks or trademarks of Adobe
Systems Incorporated in the United States and/or other countries.

8
Precautions
Refer installation work to the dealer.
Installationworkrequirestechniqueandexperi-
ences. Otherwise injury or damage to this
product may result.
Be sure to consult the dealer.
Do not insert any foreign objects.
This could permanetly damage this product.
Turn the power off immediately and contact
qualified service personnel for service.
Do not attempt to disassemble or modify
this product.
Failure to observe this may cause fire or elec-
tricshock.
Consult the dealer for the repair or inspections.
Stop operation immediately when some-
thing is wrong with this product.
Whensmokegoesupfromthisproductorthe
smellofsmokecomesfromthisproduct,con-
tinued use will result in fire, injury, or damage to
the product.
Turn the power off immediately and contact
qualified service personnel for service.
Select an installation area that can sup-
port the total weight.
Selecting an inappropriate installation surface
may cause the product to fall down or topple
over, resulting in injury.
Installationworkshallbestartedaftersufficient
reinforcement.
Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause the
product to fall down resulting in injury or accidents.
Consult the dealer for the inspections.
This product shall be installed in a vibra-
tion-free place.
Failure to observe this may cause screws and
bolts to be loosened and consequently to fall
resulting in injury.
Install this product in a location high
enough to avoid people and objects from
bumping the product.
Failure to observe this may cause a drop
resulting in injury or accidents.
Do not strike or give a strong shock to this
product.
Failure to observe this may cause injury or fire.
Turn the power off when do wiring of this
product.
Failure to observe this may cause electric
shock. A short circuit or wrong wiring may
cause fire.
Do not use this product in an atmosphere
of flammable gases.
Failure to observe this may cause injury by explo-
sion.
Avoid installing this product in locations
where it is subject to damage by salt or
corrosive gas.
Otherwise the mounting fixtures will deterio-
rate, causing the product to fall down and
leading to accidents.
Tighten screws and mounting fixtures to
the specified torque.
Failure to observe this may cause a drop
resulting in injury or accidents.

9
[Precautions for use]
This product is designed to be used
indoors.
This product is not operable outdoors.
This product has no power switch.
When turning off the power, turn off a circuit
breaker.
To keep on using with stable performance
Parts of this product may deteriorate and it
may shorten the lifetime of this product when
using in locations subject to high temperatures
and high humidity. (Recommended operating
temperature: +35 °C {95°F} or lower)
Do not expose this product to direct heat
sources such as a heater.
Handle this product with care.
Do not drop this product, nor apply shock or
vibration to this product.
Failure to observe this may cause trouble.
Do not touch the dome cover with your
bare hands.
A dirty dome cover causes deterioration of pic-
ture quality.
Noise on monitor
This product is equipped with a super sensitive
CCD. Therefore, noise may appear on the
monitor. This phenomenon is not trouble.
Discoloration on the CCD color filter
When continuously shooting a bright light
source such as a spotlight, the color filter of
the CCD may have deteriorated and it may
cause discoloration. Even when changing the
fixed shooting direction after continuously
shooting a spotlight for a certain period, the
discoloration may remain.
Do not aim this product at strong light
sources.
A light source such as a spot light causes a
blooming (light bleeding) or a smear (vertical
lines).
Cleaning this product body
Turn the power off when cleaning this product.
Do not use strong abrasive detergent when
cleaning this product. Otherwise, it may cause
discoloration.
Blooming
Smear Bright subject

10
Precautions for installation
Panasonic assumes no responsibility for
injuries or property damage resulting from
failures arising out of improper installation
or operation inconsistent with this docu-
mentation.
This product is designed to be used
indoors.
This product is not operable outdoors.
Do not expose the product to direct sunlight
for hours and do not install the product near a
heater or an air conditioner. Otherwise, it may
cause deformation, discoloration and malfunc-
tion. Keep the product away from water and
moisture.
Installing place
Contact your dealer for assistance if you are
unsure of an appropriate place in your particu-
lar environment.
 • Make sure that the installation area is
strong enough to hold the product, such
as a concrete ceiling.
 • Installthecamerainthefoundationareaof
the architecture or where sufficient
strength is assured.
 • If a ceilingboardsuch as plaster boardis
too weak to support the total weight, the
area shall be sufficiently reinforced.
Avoid installing this product in the follow-
ing locations.
 • Locationwhereitmaygetwetfromrainor
water splash.
 • Locationswhereachemicalagentisused
such as a swimming pool.
 • Locationssubjecttosteamandoilsmoke
suchasakitchen.
 • Locationsnearflammablegasorvapor.
 • L
ocations where radiation or x-ray emissions
are produced.
 • Locations where corrosive gas is produced,
Locations where it may be damaged by
briny air such as seashores.
 • Locations where the temperature is not
within –10 °C to +50 °C {14°F to 122°F}.
 •
Locations subject to vibrations (This product
is not designed for on-vehicle use.)
 • Locations subject to condensation as the
result of severe changes in temperature (In
case of installing the product in such loca-
tions, the dome cover may become foggy
or condensation may be caused on the
cover.)
Avoid moist or dusty places to install this
product.
Otherwise, lifetime of the internal parts may be
shortened.
Avoid installing this product in a place
with a high level of noise.
Installation near an air conditioner, an air clean-
er,avendingmachine,orthelikecausesnoise.
Avoid installing and connecting during a
lightning storm. Otherwise, an electric
shock or fire may be caused.
Be sure to remove this product if it is not
in use.
Do not damage the power plug or cable.
Keep the camera cable away from the
lighting cable.
Failure to observe this may cause noise.
Radio interference
When the camera is used near TV/radio anten-
na, strong electric field or magnetic field (near a
motor or a transformer), images may be dis-
torted and noise sound may be produced. In
such a case, run the camera cable through
specializedsteelconduittubes.

11
Locally procure the screws
Screws are not supplied with this product.
Prepare the screws according to the material,
structure, strength and other factors of the
mounting area and the total weight of objects
to be mounted.
Screw tightening
 • The screws and bolts must be tightened
with an appropriate tightening torque
according to the material and strength of
the installation area.
 • Do not use an impact driver. Failure to
observe this may cause overtightening and
consequently damage to the screws.
 • When a screw is tightened, make the
screw at a right angle to the surface. After
tightening the screws or bolts, perform
visualchecktoensuretighteningisenough
andthereisnobacklash.

12
Major operating controls and their functions
(This illustration represents WV-CF634.)
1Video output connector
Transmits composite video signals.
2Mark
This mark is used when the dome cover is
installed.
3Lens
4
Focus knob
CF634
Focus knob (with lock function)
CF624
Locks the focus position after focus adjust-
ment.
5Zoom knob (with lock function)
Locks the zoom position after zoom adjust-
ment.
6Tilting lock screw
Locks the tilting position.
7AF button [AF] CF634
page 21.
8Setup button [SET]
Press the [SET] button once and the “FOCUS
ADJUSTMENT” screen will be displayed.
Hold down the [SET] button for more than 2
seconds and the setup menu will be
displayed.
•[LEFT]/[RIGHT]: Press the [RIGHT] or
[LEFT] button to move to the right or left in
the menu, or change the displayed values.
•[UP]/[DOWN]: Press the [UP] or [DOWN]
button to move up or down in the menu.
G
F
1
2
3
4
5
6
7
8
9
A
B
C
D
E
<
• [SET]: Press this button in the menu to confirm
the selected value or function. In addition, this
button is used to open submenus.
9Adjustment monitor output jack
Connect the adjustment monitor (small LCD
monitor, etc.) to the adjustment monitor
output jack to adjust the camera angle.
@Panning table lock screw [LOCK]
Locks the panning position after adjustment.
AAzimuth adjuster
Adjusts the azimuth angle of the camera.
BTilting table
Adjusts the tilting position of the camera.
CPanning table
Adjusts the panning position of the camera.
DCable access hole
EPower cord
Supplies 24 V AC or 12 V DC from an
external power source.
FDust guard cap
A rubber cap which prevent dust go into the
camera through the cable access hole.
GFingerplate
This is where to put your fingers when
removing the dome cover.

13
Installation
place Applicable mount bracket Recommended screw Number of screw
Minimum pull-out
strength (per 1 pc.)
Ceiling / wall One-gang junction box
(locally procured) M4 2 pcs. 196 N {44.06 lbf}
Ceiling / wall (Direct mounting) M4 2 pcs. 196 N {44.06 lbf}
Ceiling WV-Q174
(approx. 310 g {0.66 lbs}) - - *1
*1 Make sure that the installed mount bracket can support more than 5 times of the weight of the
camera.
When installing the camera on a wall or ceiling, two are two methods as specified below.
 • Usetheone-gangjunctionbox
 • Installingthecameradirectlyonawallorceiling
 • UsingtheoptionalceilingmountbracketWV-Q174(forembeddedinstallationonaceiling)
Important:
 • Procure2screws(M4)tosecurethecameratoawallorceilingaccordingtothematerialofthe
installation area. Do not use wood screws and nails. For mounting a camera on a concrete wall
or ceiling, use an anchor bolt (M4) for securing.
(Recommended tightening torque M4: 1.6 N·m{1.18 lbf·ft})
 • Requiredpull-outstrengthofasinglescrew/boltis196N{44.06lbf}ormore.
 • Ifaceilingboardsuchasplasterboardistooweaktosupportthetotalweight,theinstallation
area shall be sufficiently reinforced.
 • Theprotectionsheetattachedtothedomesectionshouldbepeeledoffafterinstallation.
The mounting conditions of the camera are described as follows:
Remove the dome cover
1Peelofftheprotectionsheetfromthedome
cover. Don't remove completely as this pro-
tects the dome during installation.
2Loosen the dome cover fixing screw.
3Adjust the mark on this unit to [|] on the
dome cover, and turn the dome cover
counterclockwise to remove it.
Preparations
Mark
Mark [|]
NOTE:
 • Thecleardomecoverandtheinnerdome
are joined into a single unit.
Therefore,nevertrytoremovethem.

14
 About the side cable access hole
If you choose not to drill hole in the wall or
ceiling, but to wire the camera with the cable
exposed, cut the cable access hole on the side
of the dome cover to provide a cable entry.
Precautions when wiring from the side:
• Removethedustguardcap.Runthecable
through the cable access hole and bend it
inward, then reinstall the dust guard cap.
• Movethecabletoonesideasshown.
• Be careful not to pinch the cable with the
dome cover.
Installation method of camera
Using a gang junction box
(locally procured)
When using a gang junction box (4 inches x
2-3/8 inches), procure one locally that meets
the dimensions in the figure.
Next locally procure 2 camera-mounting screws
suitable for the installation surface and structure
of the wall/ceiling or gang junction box.
1 Attach the gang junction box to the wall or
ceiling.
2Attach the camera to the gang junction box
with the 2 screws (locally procured).
3Tighten all mounting screws.
Side cable
access hole
83.5 mm
Screws
(M4, locally procured)
Gang junction box
(locally procured)
Installation mark
{3-9/32 inches}

15
Installing the camera directly on a wall or ceiling
Affix the installation template label (accessory) to the ceiling or wall, and use a pen to mark the posi-
tions of the screws and cable mounting hole in the ceiling or wall.
Remove the installation template label, and attach the camera with 2 screws (M4, locally procured).
29 mm
{1-1/8
inches
}
83.5 mm
{3-9/32
inches
}
21 mm
{13/16
inches
}
Recommended screw
(M4, 2 pcs.)
Screws (M4, locally procured)
Side cable
access hole
Cable mounting hole
in ceiling or wall
Installation template
label (accessory)
Connections
Power cord
Video output
connector
Important:
• Besuretoturnoffthepowerofeach
device before connecting.
 • Besuretosecurethecoaxialcable
connectors.
Connect a coaxial cable to the video output
connector.
Connect the power supply
Connect the two-color conductor cable of the
camera to the power supply. The colors and
functions of the conductors are shown below.
Color 12 V DC 24 V AC
Brown Positive Live
Blue Negative Neutral
Connect the video output
Caution:
 • ONLY CONNECTWV-CF634,WV-CF624TO24VACOR12VDCCLASS2POWERSUPPLY.

16
Important:
 • Thepowersupplyof24VAC/12VDCshallbeinsulatedagainst120VAC.
 • Thepowersupplyisautomaticallyswitchovereither24VACor12VDC.Nosettingisrequired
with this camera.
Cable length and wire gauge
24 V AC
The recommended cable length and wire gauge are shown in the table for reference. The voltage
supplied to the power terminals of the camera should be within 19.5 V AC and 28 V AC.
Therecommendedwiresizefor24VACpowercordisshownbelow:
12 V DC
Calculation of the relation among the cable length, resistance, and power supply.
The voltage supplied to the camera shall be between 10.8 V DC and 16 V DC.
10.8 V DC ≤VA- 2 (R x I x L) ≤16 V DC
L: Cable length (m)
R: Resistance of copper wire (Ω/m)
VA: DC output voltage of power supply unit
I: DC current consumption (A)
See specifications.
Resistance of copper wire [at 20 °C {68 °F}]
Copper wire
size(AWG)
#24
(0.205 mm2)
#22
(0.325 mm2)
#20
(0.519 mm2)
#18
(0.833 mm2)
#16
(1.307 mm2)
Length
(approx.)
(m) 20 30 45 75 120
feet 66 100 150 250 395
Copper wire
size(AWG)
#24
(0.205 mm2)
#22
(0.325 mm2)
#20
(0.519 mm2)
#18
(0.833 mm2)
#16
(1.307 mm2)
Resistance
Ω/m 0.083 0.052 0.033 0.020 0.013

17
Installation of camera
Turn off the power of all related devices before installation.
1 Remove the camera dome cover.
2Connect all cables.
If necessary, bind the cable with cable tie (locally procured).
3Install the camera (The illustration below shows installation using a gang junction box (locally
procured) ).
Mount the camera with 2 screws (M4, locally procured).
Important:
•Besuretoavoidtwistingthecableswhentighteningthescrews.
Note:
•Whenattachedtotheceiling:
Install the camera with its front (Model number indication face) facing the direction opposite to
the “ TOP”arrowoftheinstallationmark(“ FRONT” direction of the installation template label
in the accessories).
•Whenattachedtothewall:
Install the camera with the “ TOP”arrowoftheinstallationmarkfacingupward.
Installation
Screws
(M4, locally procured)
Installation
mark

18
1 Connect the ∅3.5 mm miniature plug (mono channel) to the adjustment monitor output jack.
Important:
•This video output is intended for confirmation of view angle, etc. during installation or repair
service, and not for recording or monitoring.
Note:
•Video cannot be output through the video output cable after connecting the adjustment
monitor.
2Pan, tilt and azimuth adjustment
Important:
•Whenadjustingpan,tiltorazimuth,donotholdthelensofthecamera.
1Adjustment of panning position
Loosen the panning table lock screw and
rotate the table to determine the panning
position (adjustable range: 350°).
• The panning position can be adjusted
between +180° (clockwise) and –170°
(counter-clockwise).
• Afterthepanningpositionisdetermined,fix
the panning table with the panning table
lockscrew.
(Recommended torque: 0.39 N·m {0.29 lbf·ft})
2Adjustment of tilting position
Turn the tilting table to adjust the tilting
position of the camera. (adjustable range:
±90 °)
• Theviewanglecanbeadjustedasthecam-
era uses vari-focal lens.
• Tightenthetiltinglockscrewafter
adjustment.
(Recommended torque: 0.59 N·m {0.43 lbf·ft})
Adjustment
Original position mark
Panning table
Panning table lock
screw[LOCK]
Clockwise: +180 º
Counter-
clockwise: -170 º
Adjustable range: ±90 º

19
3Adjustment of azimuth
Adjust the azimuth by rotating the azimuth
adjuster. (adjustable range: ±100 °)
Note:
• Adjustazimuthsothattheimagetopmarkisfacing“∆” to display the image properly rather
than upside-down.
Image top mark
TOPmark
azimuth adjuster
Rotation
angle: +100 º
Rotation
angle: -100 º
Image top mark

20
3Zoomandfocusadjustment
Perform the zoom and focus adjustments at the same time as pan and tilt adjustments (Step 2).
Note:
• If the camera is used in near-horizontal position, the shadow of the dome cover may appear in
the image.
1Loosen the zoom knob and focus knob. Select photographic subject and choose proper view
angle through zooming. Adjust the zoom and focus rings to make the image clear (approximate
adjustment).
Note:
•
The focus may not be adjusted smoothly when the zoom ring is extremely close to the end of
W direction (T direction). At this time, slightly adjust the zoom ring towards the T direction (W
direction), and then adjust the focus.
2Tighten the zoom knob.
3Press the [SET] button.
→The “FOCUS ADJUSTMENT” screen will appear.
The focus assist function will be activated to perform the optimum adjustment.
4 When the focus ring is positioned near the best focus position, the position will automatically be
memorized as the "PEAK HOLD" position (the higher the value is, the closer it is to the focus point).
5When the focus ring is moved, the current focus position will be indicated on "INDICATOR" .
Adjust the focus position so that the indicator value goes close to the "PEAK HOLD" position.
6 Whentheindicatorvaluegoestothebestfocusposition,"BESTFOCUS"willbedisplayedinreverseat
the lower right corner of the screen.
7Press the [SET] button again to close the "FOCUS ADJUSTMENT" menu. (No operation for 3
minutes also closes the menu.)
8Tighten the focus knob.
Important:
• If the view angle changes during adjustment, press the [SET] button to close the “FOCUS
ADJUSTMENT” screen (once the view angle changes, the “PEAKHOLD” and “INDICATOR”
values will also change), and repeat from step 4after the view angle is fixed.
•
When shooting in the following place or following subjects, press the [SET] button again to close
the “FOCUS ADJUSTMENT” screen, or adjust to the best focus position while viewing the image.
•Frequentlymovingsubject
NEAR
FAR
TELE
WIDE
Lens
Zoom knob
Focus knob
..................I
HIGHLOW
INDICATOR 1135
BEST
PEAK HOLD
1135 FOCUS
FOCUS ADJUSTMENT
LOW HIGH
...................I
INDICATOR 1135 BEST
PEAK HOLD 1135 FOCUS
<AdjustmentonWV-CF624>