Panasonic AKHC900 - COLOR CAMERA User manual

Panasonic Broadcast
AK-HC900
Menu Information

18
USER MENU
1.MAINTENANCE
2.SETTING
3.CAM ID
4.FILE MENU
MAINTENANCE
1.BLACK SHADING
2.PED,GAMMA,FLARE
3.KNEE,WHITE CLIP
4.R/B GAIN
5.DTL
6.GAIN,AUTO IRIS
7.S.GAIN 1
8.S.GAIN 2
9.S.GAIN 3
10.FRAME MODE
11.COLOR CORRECTION1
12.COLOR CORRECTION2
°°
SETTING
1.MODE
2.SHUTTER
3.H.PHASE
°° °°
°°
CAM ID
ID:AKHC900
°°
H
H
FILE MENU
FILE :USER1
(DATA REF :PRESET)
SAVE FILE? :USER1
SAVE :
°°
File managing & renewing menu
USER MENU
Maintenance menu
Using condition setting menu
Camera ID setting menu
Setting of Menu Items
_Configuration of menu display screen

19
USER MENU
1.MAINTENANCE
2.SETTING
3.CAM ID
4.FILE MENU
Setting of Menu Items
_USER menu (Initial screen)
The readout data at start of power supply is
the data just before cutting off the power
supply, and the operation is started with the
data.
1. MAINTENANCE
It sets various adjusting data.
2. SETTING
It sets various modes.
3. CAM ID
It sets the camera ID.
4. FILE MENU
It executes file loading and saving, and
makes the basic setting of data display.
Menu operation is executed by the HD Controller AK-HRP900.

20
MAINTENANCE
1.BLACK SHADING
2.PED,GAMMA,FLARE
3.KNEE,WHITE CLIP
4.R/B GAIN
5.DTL
6.GAIN,AUTO IRIS
7.S.GAIN 1
8.S.GAIN 2
9.S.GAIN 3
10.FRAME MODE
11.COLOR CORRECTION1
12.COLOR CORRECTION2
°°
°BLACK SHADING°
DETECTION
CORRECT(DIG) :ON
Setting of Menu Items
!Maintenance menu
≥Move the cursor (arrow mark) to the item
to be adjusted and press the MENU key,
then it enters the adjustment menu there-
under.
≥Move the cursor to MAINTENANCE and
press the MENU key, then it returns to
USER MENU.
1Black shading correction menu
≥When MENU key is pressed at DE-
TECTION, (BLK-SHD:ACTIVE) ap-
pears, then the lens is automatically
stopped down and ABB operation is
executed.
≥When CORRECT (DIG) is turned ON,
horizontal and vertical shading correc-
tion is automatically executed.
When it is turned OFF, the current value
is maintained.
≥Move the cursor to “BLACK SHADING”
and press the MENU key, then it re-
turns to MAINTENANCE MENU.
Note:
It takes about 90 sec. until completion of
black shading correction.

21
PED,GAMMA,FLARE
M PED :+027
R PED :+000
B PED :+000
M GAMMA :0.45
R GAMMA :+00
B GAMMA :+00
R FLARE :010
G FLARE :000
B FLARE :017
GAMMA :ON
FLARE :ON
°° °°
Setting of Menu Items
!Maintenance menu
2Pedestal, gamma, flare adjustment
menu
M PED: Master pedestal can be adjusted
only by turning the control panel VR.
The R, G, B pedestal can be totally ad-
justed.
R, B PED: R, B pedestal adjustment.
Besides the master pedestal adjustment,
R, B pedestal can be independently ad-
justed. It is not related to DATA REF. The
numeral display after normal ending of
ABB is “0”for both of R, B.
M GAMMA: Master gamma adjustment.
The R, G, B gamma can be totally ad-
justed.
R, B GAMMA: R, B gamma adjustment.
Besides the master gamma adjustment,
R, B gamma can be independently ad-
justed.
R FLARE: R flare adjustment
G FLARE: G flare adjustment
B FLARE: B flare adjustment
GAMMA: Gamma ON/OFF setting
FLARE: Flare ON/OFF setting

22
KNEE,WHITE CLIP
M KNEE POINT :95.00%
R KNEE POINT :+00.00%
B KNEE POINT :+00.00%
M KNEE SLOPE :95.00%
R KNEE SLOPE :+000
B KNEE SLOPE :+000
A.KNEE POINT :95.00%
A.KNEE LVL :108
WHITE CLIP LVL :109%
KNEE :MANU
WHITE CLIP :ON
°° °°
Setting of Menu Items
!Maintenance menu
3Knee&white clip adjustment menu
M KNEE POINT: Master knee point ad-
justment.
G, B, R knee point can be totally adjusted.
R, B KNEE POINT: R, B knee point ad-
justment.
Besides the master knee point adjust-
ment, R, B knee point can be independ-
ently adjusted.
M KNEE SLOPE: Master knee slope ad-
justment.
G, B, R knee slope can be totally ad-
justed.
R, B KNEE SLOPE: R, B knee slope ad-
justment.
Besides the master knee slope adjust-
ment, R, B knee slope can be indepen-
dently adjusted.
A. KNEE POINT: Auto knee point setting.
Knee point in auto knee mode is set.
A. KNEE LVL: Auto knee level.
WHITE CLIP LVL: White clip level ad-
justment.
Video level with white clipped is set.
KNEE: KNEE mode (OFF/MANU/AUTO)
OFF: Knee function is turned OFF
MANU: Knee function is adjustable with
menu.
AUTO: Auto knee function is executed.
WHITE CLIP: White clip operation set-
ting.
With it ON, white clip is effective.

23
R/B GAIN
R GAIN :+000
B GAIN :+000
°° °°
DTL
DTL :ON
TOTAL DTL LVL :+00
H DTL LVL :11
CRISP :02
LVL DEPENDENT :2
PEEK FREQUENCY :10
KNEE APERTURE :ON
KNEE APA.LVL :10
SLIM DTL :OFF
DTL(+) :+00
DTL(-) :+00
DTL CLIP :0
DTL SOURCE :(B+G)/2
°° °°
Setting of Menu Items
!Maintenance menu
4Gain adjustment menu
The gain of R, B GAIN is adjusted.
The difference from the state of being
white-balanced can be adjusted.
≥The numeral value displayed after nor-
mal ending of AWB is “0”for both of R,
B.
5Detail adjustment menu
DTL: Setting of valid/invalid of detail func-
tion.
TOTAL DTL LVL: Horizontal and verti-
cal detail level adjustment.
H DTL LVL: Horizontal DTL component
is adjusted independently of DTL ad-
justed by TOTAL DTL.
CRISP: It functions to eliminate slight
detail component and to reduce the noise
level.
LVL DEPENDENT: It suppresses the de-
tail of low brightness level. The bright-
ness level to be suppressed is adjusted
here.
PEAK FREQUENCY: It lifts up the detail
component, and selects the central fre-
quency.
KNEE APERTURE: It functions to em-
phasizes the detail component of the por-
tion with knee applied.
KNEE APA.LVL: It sets the degree of
knee aperture.
SLIM DTL: It validates the function of
slimming the portion where the detail is
thick and emphasized.

24
DTL
DTL :ON
TOTAL DTL LVL :+00
H DTL LVL :11
CRISP :02
LVL DEPENDENT :2
PEEK FREQUENCY :10
KNEE APERTURE :ON
KNEE APA.LVL :10
SLIM DTL :OFF
DTL(+) :+00
DTL(-) :+00
DTL CLIP :0
DTL SOURCE :(B+G)/2
°° °°
GAIN,AUTO IRIS
LOW GAIN :0dB
MID GAIN :9dB
HIGH GAIN :18dB
A.IRIS LVL :082
A.IRIS PEAK/AVG :075
A.IRIS WINDOW :NORM1
IRIS MODE :LENS
IRIS GAIN :06
°° °°
Setting of Menu Items
!Maintenance menu
5Detail adjustment menu (continued
from previous page)
DTL (i): Setting of DTL at the edge in
positive direction.
DTL (j): Setting of DTL at the edge in
negative direction.
DTL CLIP: Setting of clip level of DTL
edge.
DTL SOURCE: Setting of video source
[G, R, (3G+R) /4, (2G+R+B) /4, (G+B/2)]
to create the detail.
6Master gain, auto iris setting menu
LOW GAIN: LOW setting of master gain.
MID GAIN: MID setting of master gain.
HIGH GAIN: HIGH setting of master gain.
≥The above GAIN setting is able to set -
6 to + 18 dB in 3 dB step.
A.IRIS LVL: Setting of the intended con-
vergence level of auto iris.
A.IRIS PEAK/AVG: Setting of the detec-
tion ratio of peak value and average value
of the quantity of light when auto iris is
operated.
A.IRIS WINDOW: Setting of the detect-
ing position of auto iris.
IRIS MODE: Auto iris mode setting:
(LENS/CAM).
IRIS GAIN: Iris loop gain adjustment.

25
S GAIN 1
TOTAL GAIN :62dB
ANLG GAIN :36dB
PIX MIX :06dB
V MIX :OdB
FRAME MIX :20dB
H DTL LVL :00
CRISP :0
LEVEL DEPENDENT :5
PEAK FREQUENCY :2
M GAMMA :0.45
MASTER PED OFFSET :-043
R PED OFFSET :-046
B PED OFFSET :-045
°° °°
°
H FRAME MODE
1.SCAN REVERSE :OFF
°°
Setting of Menu Items
7Super gain, Detail, Pedestal-offset
level setting menu
TOTAL GAIN: Total gain in analog, pixel
addition, and memory addition is dis-
played.
ANLG GAIN: Gain setting in analog.
PIX MIX: Gain setting in horizontal pixel
addition. Capable of setting 0/6 dB.
V MIX: Gain setting in vertical pixel addi-
tion. Capable of setting 0/6 dB.
FRAME MIX: Gain setting in memory ad-
dition. Capable of setting 0/6/12/15/20
dB.
H DTL LVL: DTL level setting of super
gain.
CRISP: Setting the function of reducing
noise level of super gain. It is invalid
when DTL level is “0.”
LEVEL DEPENDENT: Setting of DTL
suppression at low lighting intensity of
super gain.
PEAK FREQUENCY: Setting of DTL
boost frequency of super gain.
M GAMMA: Gain setting in super gain.
Capable of setting 0/6 dB.
MASTER PED OFFSET: Setting of mas-
ter pedestal offset of super gain 1.
R PED OFFSET: Setting of R pedestal
offset of super gain.
B PED OFFSET: Setting of B pedestal
offset of super gain.
!Maintenance menu
8Setting menu in frame mode
SCAN REVERSE: Capable of changing
the right and left pictures, the top and bot-
tom pictures with each other, respectively.
(Super gain 1, 2, 3 are same menu.)

26
Setting of Menu Items
!Maintenance menu
9Color correction 1 menu
Adjustment of gain (saturation) and phase
of each color.
< COLOR CORRECTION1 >
SAT PHASE
R +00 +00
Mg +00 +00
B +00 +00
Cy +00 +00
G +00 +00
Y1 +00 +00
< COLOR CORRECTION2 >
SAT PHASE
R - Mg +00 +00
Mg - B +00 +00
B - Cy +00 +00
Cy - G +00 +00
G - Y1 +00 +00
Y1 - R +00 +00
qZ Color correction 2 menu
Adjustment of gain and phase of matrix.