Panasonic WV-SFV531 User manual

WV-SFV531
Installation Guide
Network Camera
in China
● This manual describes the installation procedures, network camera installation, cable connec-
tions, and the angle of view adjustment.
● Before reading this manual, be sure to read the Important Information.
Parts and functions
The component names of the camera are as follows. Refer to the illustration when installing or
adjusting the camera.
Standard accessories Making connections
Important Information ............................... 1 pc.
Installation Guide (this document) ............ 1 set
Warranty card ........................................... 1 set
CD-ROM*1 ................................................ 1 pc.
Code label*2 .............................................. 1 pc.
*1 The CD-ROM contains the operating instructions and different kinds of tool software pro-
grams.
*2 This label may be required for network management. The network administrator shall retain
the code label.
The following parts are used during installation procedures.
Ⓐ Attachment plate .................................. 1 pc.
Ⓑ Base bracket........................................ 1 pc.
Ⓒ Fixing screws for attachment plate
(M4 × 8 mm) ...................................... 5 pcs.
(of them, 1 for spare)
Ⓓ 4P alarm cable ..................................... 1 pc.
Ⓔ MONITOR OUT conversion plug ......... 1 pc.
Ⓕ Template A (for the attachment plate) . 1 sheet
Ⓖ Template B (for the base bracket) ... 1 sheet
Ⓗ Bit (Hex wrench, screw size 6.35 mm
{1/4 inches} T20) ................................. 1 pc.
Ⓘ 2P power cable .................................... 1 pc.
Ⓙ LAN connector cover ........................... 1 pc.
Ⓚ Waterproof tape ................................... 1 pc.
Ⓛ Auxiliary handle ................................... 1 pc.
Ⓗ Ⓚ
● How to initialize the camera
Follow the steps below to initialize the network camera.
q Turn o󰀨 the power of the camera. When using a PoE hub, disconnect the LAN cable from the camera.
When using an external power supply, disconnect the 2P power cable plug from the camera.
w Turn on the power of the camera while holding down the INITIAL SET button, and keep the INITIAL
SET button held down till the SD MOUNT indicator is lit in green (more than 10 seconds). In
about 2 minutes after releasing the INITIAL SET button, the camera will start up and the settings
including the network settings will be initialized.
● When data is being sent via the network camera Blinks green (accessing)
Turn off each system’s power supply before making a connection. Before making connections,
prepare the required peripheral devices and cables.
* Use a LAN cable (category 5e or better, 8 pins, straight).
● When the camera is able to communicate with the Lights orange
connected device
● When an SD memory card*1 is inserted and could Lights off → Blinks green →
be recognized Lights off
● When data can be saved after the SD memory card is Lights off → Lights green
inserted and the SD ON/OFF button is pressed
(less than 1 second)
● When data can be saved to the SD memory card Lights green
● When the SD memory card is removed after holding
Lights green → Blinks green →
down the SD ON/OFF button (about 2 seconds) Lights off (recording)
Lights green → Lights off
(waiting for recording)
● When data cannot be saved to the SD memory card
Lights off
because an abnormality was detected or the SD
memory card is configured not to be used
IMPORTANT:
● When the camera is initialized, the settings including the network settings will be initial-
ized. Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not be
initialized.
● Before initializing the settings, it is recommended to write down the settings in advance.
● Do not turn off the power of the camera during the process of initialization. Otherwise, it
may fail to initialize and may cause malfunction.
IMPORTANT:
● Use all 4 pairs (8 pins) of the LAN cable (category 5e or better, straight).
● The maximum cable length is 100 m {328 feet}.
● Make sure that the PoE device in use is compliant with IEEE802.3af standard.
● When connecting both the 12 V DC power supply and the PoE device for power sup-
ply, 12 V DC will be used for power supply*.
* If a 12 V DC power supply and a PoE hub or router are used at the same time, net-
work connections may not be possible. In this case, disable the PoE settings.
Refer to the operating instructions of the PoE hub or router in use.
* In the situation where a 12 V DC power supply and a PoE hub or router are used at the
same time and the 12 V DC power supply is then disconnected, the power supply may
be stopped and the camera may restart depending on the PoE hub or router used.
● When the LAN cable is disconnected once, reconnect the cable after around 2 seconds.
When the cable is quickly reconnected, the power may not be supplied from the PoE device.
● When cables are used outdoors, there is a chance that they may be affected by lightning.
In this case, install a lightning arrester just before where the cables connect to the camera.
Connect a LAN cable to the RJ45 (female) network cable
Waterproof treatment for the cable joint sections
When connecting to a network using a PoE hub
Microphone/line input cable
Connect a stereo mini plug (ø3.5 mm).
● Input impedance: Approx. 2 kΩ (unbalanced)
● Recommended cable length: Less than 1 m {3.28 feet} (for microphone input)
Less than 10 m {32.8 feet} (for line input)
● Recommended microphone: Plug-in power type (option)
● Supply voltage: 2.5 V ±0.5 V
● Recommended sensitivity of microphone: –48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
● Input level for the line input: Approx. –10 dBV
IMPORTANT:
● Be sure to use the Ⓓ 4P alarm cable (accessory) provided with this product.
● When using the EXT I/O terminals as the output terminals, ensure they do not cause
signal collision with external signals.
● Install external devices so that they do not exceed the ratings above.
Connect the alarm input/output cable
<Ratings>
• ALARM IN1(DAY/NIGHT IN), ALARM IN2, ALARM IN3
Input specication: No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF: Open or 4 V - 5 V DC
ON: Make contact with GND (required drive current: 1 mA or more)
• ALARM OUT, AUX OUT
Output specication: Open collector output (maximum applied voltage: 20 V DC)
Open: 4 V - 5 V DC by internal pull-up
Close: Output voltage 1 V DC or less (maximum drive current: 50 mA)
* The default of EXT I/O terminals is “O󰀨”.
Connect an external amplifier-embedded speaker to the audio output cable
Connect a stereo mini plug (ø3.5 mm).
● Output impedance: Approx. 600 Ω (unbalanced)
● Recommended cable length: Less than 10 m {32.8 feet}
● Output level: –20 dBV
IMPORTANT:
● Connect/disconnect the audio cables and turn on the power of the camera after turn-
ing off the power of the audio output devices. Otherwise, loud noise may be heard
from the speaker.
● Make sure that the stereo mini plug is connected to this cable. When a monaural mini
plug is connected, audio may not be heard.
When connecting a monaural speaker with amplifier, use a locally procured conver-
sion cable (mono-stereo).
Adequate waterproof treatment is required for the cables when installing the camera with cables
exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are
not waterproof.
Be sure to use the supplied waterproof tape at the points where the cables are connected to ap-
ply waterproof treatment in the following procedure. Failure to observe this or use of a tape other
than the Ⓚ waterproof tape (accessory) (such as a vinyl tape) may cause water leakage resulting
in malfunction.
Before starting the installation, check the entire system conguration. The following illustration
gives a wiring example of how to connect the camera to the network via a PoE device (hub).
<LAN cable> < Alarm input/output cable, power cable, micro-
phone/line input cable, audio output cable>
IMPORTANT:
● Also waterproof the Ⓘ 2P power cable (accessory), Ⓓ
4P alarm cable (accessory), and external connections
in the same way.
● Stretch the tape by approx. twice (see the illustration)
and wind it around the cable. Insufficient tape stretch
causes insufficient waterproofing.
● To prevent the LAN cable hook from coming loose
easily, fit the Ⓙ LAN connector cover (accessory)
onto the pigtail cable as illustrated, and then slide it in
the direction indicated by the arrow.
The connector of the LAN cable used with this cam-
era must meet the following restrictions.
Height when inserted (From bottom to hook.):
Max. 16 mm {5/8 inches}
Connector width: Max. 14 mm {9/16 inches}
● To install this product outdoors, be sure to waterproof
the cables. Waterproof grade (IEC IP66 or equivalent) is
applied to this product only when it is installed correctly
as described in these operating instructions and appro-
priate waterproof treatment is applied. The internal parts
of Ⓑ base brackets (accessory) are not waterproofed.
2x
WV-SFV531
WV-SFV531
IMPORTANT:
● The adjustment monitor is used for checking the adjustment of the angular field of view
when installing the camera or when servicing. It is not provided for recording/monitoring use.
● Depending on the monitor, some characters (camera title, preset ID, etc.) may not be
displayed on the screen.
● Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
● If a PoE hub is not used, each network camera must be connected to a 12 V DC
power supply.
● When using 12 V DC, power supply from a PoE hub or router is not required.
INITIAL SET button (Initializing / NTSCPAL switch button)
Dehumidifying
device
Auto focus ( AF ) button
• FRONT must posi-
tioned in front of the
camera (on the
Panasonic logo side).
Direction marker
for installation
(FRONT )
Ⓙ
LAN connector cover (accessory)
Wind the tape in a
half-overlapping
manner.
Wind the tape in a
half-overlapping manner.
(Hex wrench, screw size
6.35 mm {1/4 inches} T20)
ACT indicator
SD MOUNT indicator
*1 SDXC/SDHC/SD memory card is described as SD memory card.
*2
Depending on the scanning application used, the Data Matrix may not be able to be
read correctly. In this case, access the site by directly entering the following URL.
http://security.panasonic.com/pss/security/support/qr_sp_select.html
MONITOR OUT terminal
(factory shipment: NTSC
monitor)
Connect the output cable of the AC adaptor to the Ⓘ 2P power cable (accessory).
Power cable
12 V DC
Red Positive
Black Negative
<Required cable>
LAN cable (category 5e or better, straight)
Use a LAN cable (category 5e or better, cross) when directly connecting the camera to a PC.
* Recommended cable length from the speaker: less than 10 m {32.8 feet}
Recommended cable length from the microphone: less than 1 m {3.28 feet}
For U.S. and Canada:
Panasonic System Communications
Company of North America,
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Two Riverfront Plaza, Newark, NJ 07102-5490
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada
[phone]
www.panasonic.ca
For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com
Panasonic Corporation
Osaka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Connect the power cable
IMPORTANT:
● The 12 V DC power supply shall be insulated from the commercial AC power.
● Be sure to use the
Ⓘ 2P power cable (accessory) provided with this product.
● Be sure to fully insert the
Ⓘ 2P power cable (accessory) into the 12 V DC power
supply terminal. Otherwise, it may damage the camera or cause malfunction.
● When installing the camera, make sure that excessive force is not applied to the power cable.
● Be sure to use an AC adaptor compliant with the Specifications (written in the indication
label on the bottom side of this unit) regarding power source and power consumption.
Caution:
● A READILY ACCESSIBLE DISCONNECT DEVICE SHALL
BE INCORPORATED TO THE EQUIPMENT POWERED
BY 12 V DC POWER SUPPLY.
● ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL
1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/
UL/CSA 60950-1).
Included Installation Instructions
© Panasonic Corporation 2017
Ⓓ 4P alarm cable (accessory)
GND (black)
ALARM IN3, AUX OUT, DAY (gray) (Alarm input 3, AUX output switching output)
ALARM IN2, ALARM OUT (red) (Alarm input 2, Alarm output)
ALARM IN1, DAY/NIGHT IN (green) (Alarm input 1/DAY/NIGHT switching input)
Stretch the tape to
about twice.
Max. width
Max. height
Powered speaker Adjustment monitor
PC
PoE device (hub)
LAN cable
(category 5e or
better, straight)
LAN cable
(category 5e or
better, straight)
LAN cable
(category 5e or
better, straight)
Adjustment monitor
Recommended total
extended cable length*
Powered speaker
Microphone
Microphone
SD slot
SD ON/OFF button
● Points up when installing to a wall.
● When the INITIAL SET button (i.e. the initializing button) is pressed (less than 1 second)
to
switch the output signal of the MONITOR OUT terminal (NTSCPAL output), the MONITOR
OUT terminal can be switched for the NTSC monitor/PAL monitor.
Dome cover
Tilting table
Panning table
Camera fixing screw
Ⓒ Fixing screws for
attachment plate
(accessory)
Enclosure Camera
Inner
cover
Ⓐ Attachment
plate (accessory)
Ⓑ Base bracket
(accessory)
Conduit wiring
connector
Note:
● Lighting/blinking LED can be turned off with the software settings at any time. (The initial
state is lighting or blinking.) Set the LED to be solid off if necessary, depending on the
installation conditions. (☞ Operating instructions included in the CD-ROM)
ⓀWaterproof tape (accessory) ⓀWaterproof tape
(accessory)
Note:
● Off, input, and output of the external I/O terminal 2 and 3 can be switched by config-
uring the setting. Refer to the operating instructions on the provided CD-ROM for fur-
ther information about the EXT I/O terminal 2 and 3 (ALARM IN2, 3) settings (“Off”,
“Alarm input”, “Alarm output” or “AUX output”).
Ⓘ 2P power cable
(accessory)
RJ45 (female)
Network cable
Alarm input/output cable
Microphone/line input cable (white)
Audio output cable (black)
LAN cable (category 5e
or better, straight)
Ⓓ 4P alarm cable
(accessory)
12 V DC power
supply terminal
12 V DC (red)
GND (black)
Screen display
top (TOP)
Model No. WV-SFV531
● When AF (Auto Focus) operation is being executed Blinks red (Interval of 1 time/ second)
● When the set is being started Lights red
● When an SD memory card is recognized normally Lights red → Lights off
●
When an abnormality is detected in SD card or the SD Lights red → Stays red
slot is not used after the camera has started
SD ERROR/AF indicator
Two-dimensional barcode
(
Data Matrix ) : To our website *2
Pan table fixing
screw with washer
ⓁZoom knob
Auxiliary
handle
LINK indicator
The hook engages with
the connector terminal
Water-proof rubber
Direction marker for installation ( TOP )
PGQX1907XA sL0615-3047 Printed

Step4 Adjustment
IMPORTANT:
● Check that the water-proof rubber installed in
the slot around the camera does not slide out
of the slot, and then mount the enclosure.
● Securely tighten all the enclosure fixing
screws (×4) of enclosure. Otherwise, the
enclosure dropping may result in injury.
(Recommended tightening torque: 0.59 N·m
{0.44 lbf·ft})
● After complete installation, remove the cover
film from the dome cover.
● Defocus may be caused by the reinstalled
enclosure. In this case, perform the auto focus
function from the setup menu.
Ⓔ MONITOR OUT conversion plug (accessory)
Note:
● Depending on the lens range or the optical zoom, it must be noted that the shadow
of the enclosure may be projected.
● When the vertical (TILT) angle of the camera is more than 75°, part of image may
appear to be overlapped. To prevent from overlapping, reduce the vertical (TILT)
angle or adjust the optical zoom.
● When mounting the camera on a wall, rotate the pan table by 180° to the left and
rotate the tilt table till the TOP mark above the lens always comes to the top side.
● When adjusting the mounting to the ceilings, the enclosure and installed auxiliary
wire may be displayed on the screen depending on the direction the camera is fac-
ing. Move the enclosure and installation auxiliary wire so that they are not displayed
on the screen.
● To remove the SD memory card, hold down the SD ON/OFF button (about 2 seconds).
When the ashing SD MOUNT indicator goes out, you can remove the SD memory card.
● After the SD memory card has been replaced, press the SD ON/OFF button (less than 1
second), and make sure the SD MOUNT indicator is continually lit.
● If you do not press the SD ON/OFF button after replacing the SD memory card, the SD
MOUNT indicator is automatically lit approximately 5 minutes later.
Ⓗ Bit
(accessory)
Installation
Step2 Fixing the bracketsStep1 Preparations
The installation tasks are explained using 4 steps.
There are 4 methods to install the camera to a ceiling or wall as described below. Prepare the
required parts for each installation method before starting the installation. The following are the
requirements for the various installation methods.
Installation method Recommended
screw
Minimum pull-out
strength (per 1 pc.)
[1] Mount the camera on the two-gang junction box
using the Ⓐ attachment plate (accessory). M4 screws × 4 196 N {44 lbf}
[2] Directly mount the camera onto the ceiling or
wall using the attachment plate (when wiring
can be installed in the ceiling or wall).
M4 screws × 4 196 N {44 lbf}
[3] Mount the camera onto the ceiling or wall
using the Ⓑ base bracket (accessory) (when
conduits are used for wiring, or when there is
no space available for wiring in the ceiling or
the wall).*1
M4 screws × 4 196 N {44 lbf}
[4] Mount the camera on the ceiling using the WV-
Q105A ceiling mount brackets (when mounting
in areas where the screws are too weak to
support the total weight, such as the plaster
board of double-ceilings).
anchor bolts × 2 *2
*1 Use 4 screws (M4 × 8 mm, accessory) to x the attachment plate to the base bracket.
*2Make sure that the installed ceiling can support more than 5 times of the weight of the cam-
era, the attachment plate and the anchor bolt.When using [4] the WV-Q105A ceiling mount
brackets, use them indoors.
IMPORTANT:
● Procure 4 screws (M4) to secure the Ⓐ attachment plate (accessory) or Ⓑ base
bracket (accessory) to a ceiling or a wall.
● The minimum required pull-out capacity of a single screw or anchor bolt is 196 N
{44 lbf} or more when mounting with the installation method [1] to [3] above.
● When mounting the camera on a concrete ceiling, use an AY plug bolt (M4) for
securing. (Recommended tightening torque: 1.6 N·m {1.18 lbf·ft})
● Select screws according to the material of the ceiling or wall that the camera will be
mounted to. In this case, wood screws and nails should not be used.
● If a ceiling board such as plaster board is too weak to support the total weight, the
area shall be sufficiently reinforced.
[1] Using a two-gang junction box
[2]
Directly mount the camera to the ceiling or wall using the attachment plate
[3] Mount the camera to a ceiling or a wall using Ⓑ base bracket (accessory)
< When using the conduit on the ceiling
or wall for wiring>
The base bracket can be fixed in any of the following 6 screwing positions
according to ceiling and wall conditions. Match the hole used when
installing the camera to any of positions A to F.
<Mounting the base bracket>
q Remove the cap for the female thread for
the conduit by using a hexagon wrench
(ISO 2936, width across flats S=5 mm
{3/16 inches}).
w Mount the attachment plate and
the base bracket.
Ⓐ Attachment plate (accessory)
Fixing screws for attach-
ment plate: ×4 (M4, locally
procured)
Ø25.4 mm*1
{1 inch}
46 mm {1-13/16 inches}
Two-gang junction box
Ⓐ Attachment plate (accessory)
Fixing screws for attachment plate: ×4 (M4, locally procured)
83.5 mm {3-9/32 inches}
Ø73 mm*2
{2-7/8 inches}
*3 The wiring hole diameter is 25.4 mm {1 inch}. Select any of the 2 base bracket fixture holes of
Ⓖ template B (accessory) when installing the base bracket. After mounting the attachment plate, the
mounting direction of the camera can be adjusted in 90° increments.
*4 When attaching the base bracket to a one-gang junction box in Position E, secure the base bracket
with 2 screws (M4, locally procured).
IMPORTANT:
● If open wiring is conducted, be sure to use conduits and run the cables inside
the tubes to protect the cables from direct sunlight.
● Installation work shall be such that there is no exposure to water into the
architecture through the conduits having been joined.
Step1
Preparations
Step2
Fixing the brackets
Step3
Mount the camera to the attachment
plate
Step4
Adjustment
FRONT
Cap for the female
thread for the
conduit
Ⓑ Base bracket (accessory)
Fixing screws (M4 × 4, locally
procured)
Minimum pull-out
strength: 196 N {44.06 lbf}
(per 1 pc.)
Ⓒ Fixing screws for
attachment plate: ×4
(accessory)
(Recommended tightening
torque: 0.78 N·m {0.58 lbf·ft})
Ⓐ Attachment plate
(accessory)
*1
If the mounting direction of the camera has already been determined
Align the FRONT direction (the direction of FRONT marker on the camera that indicates the
installation direction when installing the camera) of Ⓕ template A (accessory) with the desired
direction, and drill through a 25.4 mm {1 inch} diameter hole.
*2 If the mounting direction of the camera is not determined yet or if you want to change
the direction of the camera after it has been installed
If you want to be able to change the direction of the camera, drill through a 73 mm {2-7/8 inch-
es} diameter hole in the center. By doing so you can adjust the mounting direction of the camera
in 90° increments.
Step3 Mount the camera to the attachment plate
q Check the position of attachment
mounting screws on the rear side of
the camera.
w Connect cables to the camera according to the
instructions in “Making connections”, and mount
the camera by inserting the attachment mounting
screws into the holes of the Ⓐ attachment plate
(accessory).
e Loosen 4 enclosure fixing screws using the
Ⓗ bit (accessory), and remove the enclosure
from the camera.
t Loosen the cross-head side of tilt table xing
screw (on one side), and incline the tilt table
while keeping the TOP mark on the camera
lens head facing the front (i.e. the direction of
FRONT mark on the camera).
y Press the PUSH mark on both sides of the
inner cover at the same time, and remove
the inner cover as shown in the following
illustration.
Note::
● After cables have been connected to the camera, align the OPEN mark of the enclosure side panel with the protruding part of base
bracket, insert 2 attachment mounting screws into the attachment plate, and rotate the camera approximately 15°. The LOCK mark is
moved to the protruding part of base bracket and the camera is temporarily secured. (When directly attaching the attachment plate to a
ceiling or wall, align the OPEN mark to the tab position of the attachment plate.)
IMPORTANT:
● Be sure to tighten the camera fixing
screw. Failure to observe this may
cause camera trouble due to camera
falling. Recommended tightening
torque: 0.78 N·m {0.58 lbf·ft}
IMPORTANT:
● Disconnect the 12 V DC power source and PoE power source to prevent power from being supplied during mounting work.
● Enclosure is fixed to the camera body by the installed auxiliary wire, so please do not remove it.
● For installations on the wall, to prevent water from accumulating on the surface of the dehumidifying device, install the camera so that the
dehumidifying device does not face up. If water accumulates on the surface of the dehumidifying device, it cannot function properly.
< When drilling a hole through the
ceiling or wall for wiring>
● The female thread for conduit is compliant
with ANSI NPSM (parallel pipe threads) 3/4
or ISO 228-1 (parallel pipe threads) G3/4.
*4
Tab position
of the attach-
ment plate
(×4)
Conduit
46 mm
{1-13/16 inches}
83.5 mm
{3-9/32 inches}
Position A 85 mm {3-11/32 inches}
(85.7 mm {3-3/8 inches})
138 mm
{5-7/16 inches}
46 mm
{1-13/16 inches}
138 mm
{5-7/16 inches}
83.5 mm
{3-9/32 inches}
108.5 mm
{4-9/32 inches}
70 mm
{2-3/4 inches}
83.5 mm
{3-9/32 inches}
85 mm
{3-11/32 inches}
(85.7 mm
{3-3/8 inches})
Ø25.4 mm
{Ø1 inch}*3
Ø25.4 mm
{Ø1 inch}*3
Ø25.4 mm
{Ø1 inch}*3
Ø25.4 mm
{Ø1 inch}*3
Ø25.4 mm
{Ø1 inch}*3
Ø25.4 mm
{Ø1 inch}*3
63 mm
{2-15/32 inches}
63 mm
{2-15/32 inches}
Position D
Position E
Position B
Position C Position F
TOP mark
Cross-head
side of tilt table
fixing screw
PUSH mark
(×2) Inner cover
Inner cover
Tilting table
Tab of the
inner cover
Protruding part of
base bracket
Ⓗ Bit (accessory)
Enclosure fixing
screw (×4)
Note:
● Press the PUSH mark, release the four
tabs of the inner cover from the tilting
table, and remove the inner cover.
Press both
sides at the
same time
Press
Tab of the
inner cover
Attachment
mounting screws
Installed
auxiliary
wire
Holes of the attachment plate (×4)
* For explaination purpose, the enclosure, installed auxiliary wire, and
some parts of the camera will be hidden in the following illustrations.
Camera fixing screw
q Turn on power for the camera by either connecting
a LAN cable or a 12 V DC power cable, and then
remove the protection lm from the camera lens.
w
Connect the Ⓔ MONITOR OUT conversion plug (acces-
sory) to the MONITOR OUT terminal of the camera, and
then connect the monitor for adjustment with a RCA pin
cable (locally procured).
e
Insert an SD memory card into the slot, if necessary.
● Insert the SD memory card with its label facing down.
● For information about performing the SD memory
card setting, refer to the operating instructions
(included in the CD-ROM).
r Loosen the pan table xing screw, and
adjust the angle of the camera with the
tilt table, pan table, and azimuth adjust-
ment ring.
Horizontal (PAN) angle: ±180°
Vertical (TILT) angle: ±85°
Azimuth (YAW) angle: ±100°
t
Tighten the cross-head side of tilt table xing
screw (on one side) and the pan table xing
screw, and x the camera.
(Recommended tightening torque:
0.59 N·m {0.44 lbf·ft})
y Adjust the zoom and focus.
1. Loosen the zoom knob equipped with Ⓛ
auxiliary handle (accessory) by rotating
the knob to the left, and move it between
TELE and WIDE to obtain the appropriate
angle of view. Then, lock the zoom knob
by rotating it back to the right.
2. Adjust the focus by pressing the auto
focus (AF) button.
3. Adjust the screen size and focus by re-
peating steps 1 and 2. Readjust the angle
of the camera with the tilt table, pan table,
and azimuth adjustment ring if necessary.
u Press the PUSH mark on both sides of the
inner cover, and install the inner cover to
the place where it was removed.
i Disconnect the monitor for adjustment.
Attach the enclosure and secure it by tight-
ening the enclosure xing screws.
(Align the ▼ LOCK mark on the enclosure
with the mark on the camera. Then mount the
enclosure directly to the camera.)
▼mark
SD memory card (with label facing down)
MONITOR OUT terminal
Tilt table xing screw Tilting table
Horizontal (PAN) angle
Azimuth (YAW) angle
Azimuth adjustment ring
Pan table xing
screw with washer
Vertical (TILT)
angle Zoom knob
Ⓛ Auxiliary handle
(accessory)
Auto focus (AF) button
PUSH mark
(×2)
Inner cover
●Remove the camera using the reverse order of the installation procedures.
●After installing the camera, refer to “Congure the settings of the camera (leaet)”
and perform the camera settings.
Enclosure
r Secure the camera by tightening the camera
xing screws.
* The illustration above is the example of installation on ceiling in “Position D” of base bracket.
WIDE
TELE