Panasonic WV-V2530LK User manual

Network Camera Operating Instructions
Model No. WV-V2530LK
WV-V2530L1
WV-V1330LK
WV-V1330L1
Version 1.0.0

i
Table of Contents
1Network Connection ...................................................................................................................1
2Main Interface Introduction........................................................................................................2
2.1 Log in....................................................................................................................................2
2.2 Live Interface........................................................................................................................6
2.3 Encode Setup ........................................................................................................................7
2.3.1 Image Adjustment.....................................................................................................8
2.4 System Menu ........................................................................................................................9
2.5 Video Window Function Option ........................................................................................10
2.5.1 Zoom and Focus (WV-V2530L1, WV-V1330L1) .................................................11
3Alarm...........................................................................................................................................13
4Playback (WV-V2530LK, WV-V2530L1, WV-V1330L1).....................................................14
4.1 Playback..............................................................................................................................14
4.1.1 Function of Play......................................................................................................15
4.1.2 Playback File ..........................................................................................................16
4.1.3 Playback Cut...........................................................................................................18
4.1.4 Record Type ...........................................................................................................18
4.1.5 Progress Bar............................................................................................................18
4.1.6 Assistant Function ..................................................................................................19
4.2 Picture Playback .................................................................................................................19
4.2.1 Play .........................................................................................................................20
4.2.2 Playback File ..........................................................................................................21
4.2.3 Snapshot Type ........................................................................................................22
5Log out........................................................................................................................................23
6Setup...........................................................................................................................................24
6.1 Basic ...................................................................................................................................24
6.2 Image/Audio .......................................................................................................................25
6.2.1 Image/Audio ...........................................................................................................25
6.2.2 Image adjust............................................................................................................35
6.2.3 Profile Management ...............................................................................................42
6.2.4 Zoom and Focus (WV-V2530L1, WV-V1330L1) .................................................43
6.3 Network ..............................................................................................................................44
6.3.1 TCP/IP ....................................................................................................................44
6.3.2 Connection..............................................................................................................45
6.3.3 DDNS .....................................................................................................................47
6.3.4 IP filter ....................................................................................................................48
6.3.5 SMTP (Email).........................................................................................................49
6.3.6 UPnP.......................................................................................................................51

ii
6.3.7 SNMP .....................................................................................................................51
6.3.8 Multicast .................................................................................................................55
6.3.9 802.1x .....................................................................................................................56
6.3.10 QoS .........................................................................................................................57
6.4 Event...................................................................................................................................58
6.4.1 Video Detection......................................................................................................58
6.4.2 Audio Detection (WV-V2530LK)..........................................................................63
6.4.3 Alarm (WV-V2530LK) ..........................................................................................64
6.4.4 Abnormity (except WV-V1330LK) .......................................................................65
6.5 Storage ................................................................................................................................68
6.5.1 Schedule..................................................................................................................68
6.5.2 Destination..............................................................................................................72
6.5.3 Record Control .......................................................................................................74
6.6 System ................................................................................................................................76
6.6.1 Account (User mng.) ..............................................................................................76
6.6.2 Default reset............................................................................................................79
6.6.3 Import/Export .........................................................................................................80
6.6.4 Auto Maintenance...................................................................................................80
6.6.5 Upgrade ..................................................................................................................81
6.7 Information .........................................................................................................................82
6.7.1 Version....................................................................................................................82
6.7.2 Log..........................................................................................................................82
6.7.3 Online User.............................................................................................................83
7Using the CD-ROM...................................................................................................................84
7.1 About the CD launcher .......................................................................................................84
7.2 Installing Panasonic “IP Setting Software” ........................................................................85
7.3 Installing the manuals.........................................................................................................85
7.4 Installing the Viewer software............................................................................................86
7.5 Configure the network settings of the camera using the Panasonic “IP Setting Software”87

iii
Welcome
Thank you for purchasing our network camera!
This operation manual is designed to be a reference tool for your system.
Please open the accessory bag to check the items one by one.
Depending on the model used, the screens shown in the explanations may differ to the actual camera
screens.

1
1 Network Connection
These series network camera products support the Web access and management via PC.
Web includes several modules: monitor channel preview, system configuration, alarm and etc.
Please follow the steps listed below for network connection.
Make sure the network camera has connected to the network properly.
Network camera IP address and PC IP address shall be in the same network segment. If there is
router, please set the corresponding gateway and subnet mask.
Use order ping ***.***.***.***(* network camera address) to check connection is OK or not.

2
2 Main Interface Introduction
2.1 Log in
Open IE and input network camera address in the address bar.
For example, if your camera IP is 192.168.0.10, then please input http:// 192.168.0.10 in IE address bar.
See Figure 2-1.
Figure 2-1
The login interface is shown as below. See Figure 2-2.
Please input your user name and password to have been registered when you access the camera
at first.
Note:
- Please refer to “Network Configuration” in Installation Guide manual.
- For security reasons, please change the password periodically.
Input your IP
address here

3
Figure 2-2
.If it is your first time to login, you may see the interface window shown as in Figure 2-3
Figure 2-3
Click on “Please click here to download and install the plug-in”. The system pops up warning information
to ask you whether run or save this plug-in. See Figure 2-4.

4
Figure 2-4
You must either run or save the file to local and install it. Follow the following steps. See Figure 2-5.
Note:
The displayed screens are different by the security settings on the PC.
Figure 2-5

5
When plug-in installation completes, the installation page closes automatically. The web-end will
refresh automatically, and then you can view video captured by the camera.
Figure 2-6

6
2.2 Live Interface
After you logged in, you can see the live monitor window. See Figure 2-7.
Figure 2-7
There are three sections:
Section 1: Encode setup bar
Section 2: System menu
Section 3: Window function option bar
2
1
3

7
2.3 Encode Setup
The encode setup interface is shown as in Figure 2-8.
Figure 2-8
Please refer to the following sheet for detailed information.
SN Parameter Function
1 Menu
You can switch Live and Setup menu.
2 Stream
You can switch Main, Sub Stream 1 and 2.
The compression under distribution is displayed by Stream
change.
3 Protocol
You can select stream media protocol from the dropdown list.
There are three options: TCP/UDP/Multicast
1
7
2
3
4
5
6
8

8
4 Digital Zoom 
When the video is in the original status, click it you can
select any zone to zoom in. In the non-original status, you
can drag the zoom-in zone in specified range. Right click
mouse to restore previous status.
Click it; you can use the middle button of the mouse to
zoom in/out the video size.
5 Image Adjustment You can adjust image quality.
6 Alarm It moves to an alarm setting screen.
7 Playback It moves to a playback screen.
(WV-V2530LK, WV-V2530L1, WV-V1330L1)
8 Logout Click Logout button, system goes back to log in interface.
Image Adjustment2.3.1
Click Image Adjustment button to open picture setup interface. See Figure 2-9. This interface is
displayed under a display of Image Adjustment.
Figure 2-9
Please refer to the following sheet for detailed information.
Parameter Function
Video
setup
It is to adjust monitor video
brightness.
Note:
All the operations here apply
to WEB end only.
Please go to Setup ->
Image/Audio or Image ->
Image adjust to adjust
corresponding items.
It is to adjust monitor video
contrast.
It is to adjust monitor video
hue.
It is to adjust monitor video
saturation.

9
Reset
Restore brightness, contrast
saturation and hue to system
default setup.
2.4 System Menu
System menu is a click Setup as in Figure 2-10.
.
Please refer to chapter 6.1 Basic, chapter 6.2 Image/Audio, chapter 6.3 Network, chapter 6.4 Event,
chapter 6.5 Storage, chapter 6.6 System, and chapter 6.7 Information for detailed information.
WV-V2530LK WV-V1330LK, WV-V2530L1, WV-V1330L1
Figure 2-10

10
2.5 Video Window Function Option
The interface is shown as below. See Figure 2-11.
Figure 2-11
Please refer to the following sheet for detailed information.
SN Parameter Function
1
Original
Size
Click this button to go to original size. It is to display the actual size of
the video stream. It depends on the resolution of the bit stream.
2
Full Screen
Click it to go to full-screen mode. Double click the mouse or click the
Esc button to exit the full screen.
3
Width and
Height ratio
Click it to restore original ratio or suitable window.
4
Fluency
Adjustment
There are three levels of fluency for you to select. The default is
Normal. You may select fluent mode in case connection is slow.
5
Zoom and
Focus
Click this button and the zoom and focus interface appears on encode
setup bar, as shown in figure 2-12.
(WV-V2530L1, WV-V1330L1)
6
Snapshot
You can snapshot important video by clicking on this button. All
images are memorized in system folder: \ picture download (default).
You can go to Setup -> Image -> Image -> Path to modify the local
record save path.
7
Record
For manual record. All records are memorized in Setup -> Image ->
Image -> Path.
When connected to Panasonic’s recorder, record for Sub stream 2
may not work correctly.
8
Easy Focus
Click it, you can see there are two parameters on the preview video：
AF Peak and AF Max.
AF Peak: It is to display the video definition during the focus process.
AF Max: It is the most suitable value for the video definition.
The close the AF Peak and AF Max is, the better the focus effect is.
(WV-V2530L1, WV-V1330L1)
9
Audio output
Turn on or off audio when you are monitoring. (WV-V2530LK)
10
Bidirectional
talk
Click it to start or end bidirectional talk. (WV-V2530LK)
1 2 3 4 5
6 7 8 9 10 11

11
11
Alarm output
I
t shows if there is any alarm output, status description is as follows:
Green: means there is alarm output.
White means alarm is over.
Click on the button to force alarm to be on or off. (WV-V2530LK)
Zoom and Focus (WV-V2530L1, WV-V1330L1)2.5.1
Click this button and the zoom and focus interface appears on the encode setup bar, as shown in
Figure 2-12, please refer to the following sheet for detail information to adjust zoom and focus
configuration.
Note:
Auto-focus after zoom focus adjustment.
Disable the operation till finishing zoom and focus adjustment.
Figure 2- 12
Parameter Function
Zoom Adjust the focal length of the lens by clicking or long pressing “+”“-”buttons or moving
the slider. Step length (Speed) is used to adjust the length of one step with one click.

12
Parameter Function
Focus
Adjust the sharpness length of the lens by clicking or long pressing “+”、“-” buttons
or
moving the slider. Step length (Speed)
is used to adjust the length of one step with
one click.
Auto Focus
Click to adjust the image definition automatically.
Note:
Other lens operations are not allowed during the process of auto-focus.
Restore All
Reset the lens to zero position to eliminate the accumulative error of lens.
Note:
Please reset when the image adjustment is not clear or operating zoom focus many
times.
Refresh
Synchronize the location of drag slider of lens and zoom focus after hardware zoom
focusing.

13
3 Alarm
Click alarm function, you can see an interface is shown as in Figure 3-1.
Here you can set device alarm type and alarm sound setup.
Figure 3-1
Please refer to the following sheet for detailed information.
Type
Parameter
Function
Alarm
Type
VMD
System alarms when VMD alarm occurs.
SD Full
System alarms when SD memory card is full.
(WV-V2530LK, WV-V2530L1, WV-V1330L1)
SD Error
System records alarm info when SD memory card
error happens.
(WV-V2530LK, WV-V2530L1, WV-V1330L1)
Tampering
System alarms when tampering alarm occurs.
Audio Detection
System records alarm when audio detection
occurs. (WV-V2530LK)
External Alarm
System records alarm when alarm inputs the
device. (WV-V2530LK)
When alarm is triggered, there will be displayed on the Alarm menu and system automatically
records alarm info. The icon disappears when user click on alarm menu bar.
Note:
If alarm interface is displayed, when alarm is triggered, there will be no image prompt, but alarm record
will be in list on the right.

14
4 Playback (WV-V2530LK, WV-V2530L1, WV-V1330L1)
Web client playback supports video playback and picture playback.
Note:
Before playback, user shall set storage management as in Chapter 6.5.
4.1 Playback
The playback interface is shown as in Figure 4- 1.
Figure 4- 1
There are four sections:
Section 1: Function of play
Section 2: Playback file
Section 3: Play time cut
Section 4: Record type
Section 5: Progress bar
Section 6: Assistant function
2
3
4
1
6
5

15
Function of Play4.1.1
The function of play is shown as in Figure 4- 2.
Figure 4- 2
Parameter Function
1. Play
When you see this button, it means pause or not played record. Click on this
button, switch to normal play status.
2. Stop Click this button to stop playing.
3. Next Frame
Click on this button to go to next frame.
Note:
You shall pause record when you use this function.
4. Slow Click on this button to play slowly.
5. Fast Click on this button to play quickly.
6. Sound
When this button displays, it means audio is silent. Click on this button to
switch back to normal.
7. Volume Click on left mouse to adjust volume.
1 2
3 4 5
6 7

16
Playback File4.1.2
In calendar, blue date represents data currently has video record or snapshot. See Figure 4-3.
Figure 4-3
Parameter Function
File Type
Select “mp4”, as video playback.
Select “jpg” as picture playback.
Data Source Select only SD card.
Step 1. Click on data in blue, time axis displays record file progress bar in color. While, green represents
normal record, yellow represents motion detect record, red represents alarm record, and blue
represents manual record.
Step 2. Click on certain time on progress bar, playback starts from this time. See Figure 4-4.
Figure 4- 4
Step 3. Click on file list in Figure 4-3, select date file will be displayed in list.
Step 4. Double click on file in list, playback this file and display file size, start time and end time.
See Figure 4-5.