Panasonic MINAS A6 Series User manual

Servo Drives
Quick Start Guide
MINAS A6 Multi
PANATERM for Safety
Safe Speed Monitoring (SSM)
QS10004_V1.0_EN
2020.11 https://industry.panasonic.eu

Liability and copyright
Liability and copyright
This manual and everything described in it are copyrighted. You may not copy this manual, in
whole or part, without written consent of Panasonic Electric Works Europe AG (PEWEU).
PEWEU pursues a policy of continuous improvement of the design and performance of its
products. Therefore we reserve the right to change the manual/product without notice. In no
event will PEWEU be liable for direct, special, incidental, or consequential damage resulting
from any defect in the product or its documentation, even if advised of the possibility of such
damages.
Please direct support matters and technical questions to your local Panasonic
representative.
Panasonic Electric Works Europe AG (PEWEU)
Caroline-Herschel-Strasse 100
85521 Ottobrunn, Germany
Tel: [phone]
2 QS10004_V1.0_EN

Table of contents
Table of contents
1 Introduction................................................................................................................................. 4
1.1 Before you start................................................................................................................................ 4
1.2 About this document.........................................................................................................................4
1.3 Related documents........................................................................................................................... 4
1.4 Available software............................................................................................................................. 5
2 Functional overview................................................................................................................... 6
3 Wiring...........................................................................................................................................8
3.1 Basic wiring of the MINAS A6 Multi................................................................................................. 8
3.2 USB license dongle.......................................................................................................................... 8
3.3 Connect the PC and the driver module........................................................................................... 8
4 Functional safety configuration.............................................................................................. 10
4.1 Install PANATERM for Safety on your PC......................................................................................10
4.2 Create a safety program.................................................................................................................10
4.3 Download the safety program to the driver module....................................................................... 13
4.4 Monitor the behavior of the SSM safety function........................................................................... 14
5 Help us improve....................................................................................................................... 15
6 Record of changes................................................................................................................... 16
7 Panasonic hotline.....................................................................................................................17
QS10004_V1.0_EN 3

1 Introduction
1 Introduction
1.1 Before you start
Before operating this product, read the safety instructions in the following manuals:
•“SX-DSV03514, MINAS A6 Multi, Technical Reference – Integrated Safety Part”
•“SX-DSV03508, MINAS A6 Multi, Programming Manual – PANATERM for Safety”
This product is for industrial use only.
Electrical connections must be made by qualified electrical personnel.
1.2 About this document
This “Quick Start Guide” is intended to help you set up a MINAS A6 Multi servo drive
system. It is based on information from the MINAS A6 Multi series manuals and the practical
experience of our engineers.
Step by step instructions will guide you through configuring and programming the Safe
Speed Monitoring function (SSM) with the programming software PANATERM for Safety.
Please refer to the original documentation of our servo drive systems for detailed
information. It is available free of charge in our Panasonic Download Center.
1.3 Related documents
Select the following links to download the documents from our Panasonic Download Center.
• Safety specifications:
“SX-DSV03514, MINAS A6 Multi, Technical Reference – Integrated Safety Part”
• Information on wiring the MINAS A6 Multi servo drive system:
“SX-DSV03454, MINAS A6 Multi, Reference Specifications – Driver Module”
• Information on wiring the MINAS A6 Multi power supply module:
“SX-DSV03452, MINAS A6 Multi, Reference Specifications – Power Supply Module”
• Information on EtherCAT communication:
“SX-DSV03456, MINAS A6 Multi, Technical Reference – EtherCAT Communication
Specification”
• Description of the servo driver functions:
“SX-DSV03455, MINAS A6 Multi, Technical Reference – Functional Specification”
• Information on safety programming:
4 QS10004_V1.0_EN

1 Introduction
“SX-DSV03508, MINAS A6 Multi, Programming Manual – PANATERM for Safety”
• Information on how to reduce electromagnetic interference (EMI):
“Recommendations for EMC-compliant wiring of servo drivers and motors”
• Related Quick Start Guides:
“QS10000, MINAS A6 Multi, Position control with Beckhoff host controller over EtherCAT”
“QS10001, MINAS A6 Multi, Ethernet over EtherCAT with PANATERM”
“QS10002, MINAS A6 Multi, Safe Torque Off (STO)”
“QS10003, MINAS A6 Multi, Safe Stop 1 (SS1)”
“QS10005, MINAS A6 Multi, Position control with Omron host controller over EtherCAT”
“QS10006, MINAS A6 Multi, Position control with TRIO host controller over EtherCAT”
1.4 Available software
The following software is available free of charge in our Panasonic Download Center:
• Programming software PANATERM for Safety for MINAS A6 Multi
QS10004_V1.0_EN 5

2 Functional overview
2 Functional overview
Use the Safe Stop Monitoring function (SSM) to monitor the speed of the drive and to output
a signal when the speed drops below a specified threshold.
Use the programming software PANATERM for Safety to set up this function for the MINAS
A6 Multi servo drive system.
(1)
(2)
0
Vmax
V
t0t1t2t3t t4
(1) Enabled
(2) Result output
Safe Speed Monitoring (SSM)
[t0, t1[ Speed is above the parametrized threshold. SSM result is "0".
[t1, t2[ Speed is below the parametrized threshold. SSM result is "1".
[t2, t3[ Speed is above the parametrized threshold. SSM result is "0" again.
[t3, t4[ Speed is below the parametrized threshold. SSM result is "1" again.
Example
A servo drive system, consisting of a 15kW power supply module, an A-size 1.5kW two-axis
driver module, and two servo motors with 1.0kW and 1.5kW, is connected to a PC by a USB
cable.
Use the following accessories:
• 1 x 400V AC power supply cable
Connects the MINAS A6 Multi power supply module to the main power supply (400V AC).
• 1 x 24V DC power supply cable
Connects the power supply unit (24V DC) and the host controller.
• 1 x grounding wire (M4 round terminal)
Connects the PE terminals of the power supply module and the driver module.
• 2 x Panasonic motor cable
Connects the motor and the driver module.
6 QS10004_V1.0_EN

2 Functional overview
• 2 x Panasonic encoder cable
Connects the encoder and the driver module.
• 1 x RJ11 communication cable (2 x RJ11 plug)
Connects the power supply module and the driver module.
• 1 x feed bus bar (50mm) with end cap for the DC link bus (535V DC to 675V DC)
Connects the power supply module and the driver module.
• 1 x feed bus bar (50mm) with end cap for the control bus (24V DC)
Connects the power supply module and the driver module.
• 1 x USB license dongle
• 1 x USB cable
(1) (2) (3) (6)
(8) (7)
(4) (5)
(1) Power supply unit (24V DC)
(2) MINAS A6 Multi power supply module (400V AC, 15kW)
(3) Two-axis MINAS A6 Multi driver module (1.5kW)
(4) USB cable between PC and driver module
(5) MINAS A6 servo motor B (1.5kW)
(6) MINAS A6 servo motor A (1kW)
(7) USB license dongle for PANATERM for Safety
(8) PC with PANATERM for Safety
Set-up of a MINAS A6 Multi servo drive system - Safe Speed Monitoring (SSM)
QS10004_V1.0_EN 7

3 Wiring
3 Wiring
3.1 Basic wiring of the MINAS A6 Multi
Check the hardware connections of your servo drive system:
• 24V DC control power supply connected to X11
• 400V AC main power supply cable connected to X102
• Motor cable for servo motor A connected to X105A
• Motor cable for servo motor B connected to X105B
• Encoder cable for servo motor A connected to X9A
• Encoder cable for servo motor B connected to X9B
• X1 and X1A connected with RJ11 communication cable
• Bus bars attached to X104 and X12
• PE terminals of power supply module and driver module connected by grounding wire
For details on how to do the wiring of the MINAS A6 Multi servo drive system, refer to
“Wiring” in “QS10000, MINAS A6 Multi, Position control with Beckhoff host controller over
EtherCAT”.
3.2 USB license dongle
A USB license dongle is required to compile and download the functional safety
configuration to the driver module. Connect the license dongle to a USB port of your PC.
USB license dongle
3.3 Connect the PC and the driver module
Connect your PC and the driver module with an Ethernet cable or with a USB cable. In this
example, we use a USB cable that is connected to X8 of the driver module.
X8 connector (for functional safety configuration)
Use a commercially available USB A to mini-B cable to connect the PC to the driver module.
8 QS10004_V1.0_EN

3 Wiring
(1)
(1) X8: USB connector on driver module
QS10004_V1.0_EN 9

4 Functional safety configuration
4 Functional safety configuration
4.1 Install PANATERM for Safety on your PC
The programming software PANATERM for Safety provides a graphical environment to
create PLC-based monitoring programs for the MINAS A6 Multi servo drive system.
Install the software on your PC.
For details, refer to the “SX-DSV03508, MINAS A6 Multi, Programming Manual –
PANATERM for Safety”.
4.2 Create a safety program
The general workflow for creating a safety program is to add the devices of your servo drive
system to your project, to place them in the “Terminal Scheme” screen, and to configure the
safety functions in the“Functional Scheme” screen.
1. Start PANATERM for Safety.
2. Select the “Settings” tab.
10 QS10004_V1.0_EN