Panasonic 4301 User manual

Panasonic Electric Works Fire & Security Technology Europe AB
Jungmansgatan 12, SE-211 19 Malmö, Sweden
Tel: [phone] • Fax: [phone]
[email protected] • www.panasonic-fire-security.com
Fire alarm systems
Analog photoelectric
smoke detector
4301
•Constant sensitivity / Service signal at a fixed level of contamination
•New advanced algorithms and functions and yet compatible with older EBL systems
General
The photoelectric (optical) smoke detector
has a low profile design, unleaded
soldering and the latest IC technology,
which will secure the highest reliability
possible. In the detection chamber is a high-
efficient optical system consisting of an
LED and a photodiode with two lenses.
Scattered light (i.e. reflection of infrared
light) is used to detect smoke. The smoke
enters the detection chamber through an
insect filter and an optical labyrinth. This
construction not only improves the smoke
inflow but it also causes steam, fog, etc. to
condense into moisture on its surfaces, to
prevent false (nuisance) alarms.
The detector is supplied with two LEDs that
will light when the detector goes into alarm.
The detector is plugged in the analog base
3312x / 4313. The COM loop is connected
to the base, which also has terminals for an
external LED, e.g. 2218. The detector is
intended for indoor use in dry premises and
in the systems EBL512 / 128 / 1000 / 2000
depending on the detector mode.
Constant sensitivity
The detector maintains a constant sensitivity
regardless of its contamination. A service
signal will be given when the detector has
reached a service level.
Address / Detector mode
The address setting tool 3314 is used to set
the detector's COM loop address and the
detector mode NORMAL, 2330 or 2312 See
Planning Instructions for the system
respectively for more information about the
modes and functions.
•NORMAL mode (analog): Detector
4301 is used in the systems EBL512
(SW version > 2.0) and EBL128, also as
a spare part for the detector 3304 in
NORMAL mode.
•2330 mode (conventional): Detector
4301 is used in the systems EBL512/
1000/2000 as a spare part for the
detector 3304 in 2330 mode.
•2312 mode (analog): Detector 4301 is
used in the systems EBL512/1000/2000
as a spare part for the detector 3304 in
2312 mode.
The different modes have different functions
and features, e.g. in the 2330 mode, the
detector does the fire judgement but in the
NORMAL and 2312 modes this is done in
the c.i.e. The detector is prepared for an
"Advanced mode" to be used in conjunction
with future EBLxxx SW versions.
AI function
In the 2330 mode is the AI function used,
i.e.:
•Variable delay function, i.e. the delay
time before an alarm is influenced by
temporary smoke obscuration changes.

All technical features and data are subject to changes without notice, resulting from continuous development and improvement.
Product Leaflet Date of issue Revision / Date of revision
MEW00308 2003-04-24 6 / 2008-09-15
Type number
4301 Analog photoelectric smoke detector
+
COM loop
Ext. LED
SA(L)
SA(L)
C.i.e. EBL512 / EBL128
COM loop input
SB (C)
SB (C)
SB SB
E- E-
SA SA
E+ E+
Mark Mark
SB
E-
SAo
E+
Mark
SAi
3312 4313 3312FL/F
In the detector: See also "Engineering Instructions for detectors Type 430x".
SA/SB Contact pins for COM loop / address setting tool 3314
E+/E- Contact pins for External LED
Tl Type number label; Detector type
Al Address label; For the programmed COM loop address to be written.
Lsh Locking screw hole (prepared for drilling through detector body)
Ls Locking screw
Prepared for mechanical locking with analog base 3312x / 4313. One hexagon socket screw
(Ls) is attached (1.5 mm Hex key to be used). The 2.5-2.7 mm hole (Lsh) has to be drilled.
Technical data
Voltage (V DC)
rated
allowed
normal (on COM loop)
28
12-30
24
Current consumption at nom. volt.
from COM loop (mA)
quiescent
active (incl. internal LED)
ext. LED (connected via base 3312)
0.3
2.3
max. 2
Ambient temperature (°C)
operating
storage
-10 to +50
-25 to +75
Ambient humidity (% RH) max. 95, non condensing
Ingress Protection rating (estimated) IP 51
Sensitivity (obscuration; %/m)
NORMAL mode
2330 mode
2312 mode
Depending on the mode.
3.6 / 3.0 / 2.4 (Low / Normal / High)
3.5 (Normal)
2.6
Size ∅x h (mm) 102 x 36
Weight (g) 68
Construction / Colour Modified polycarbonate / Grey (N8, Munsell colour code)
Approvals 05 EC Certificate no. 0786-CPD-20144, EN54-7
SB
SA
E-
E+
Tl
Ls
Lsh
Al
The detector is plugged in the analog base 3312x / 4313.
The COM loo
p
/ Ext. LED are connected to the analo
g
base.