Panasonic EBL128 User manual

PANASONIC FIRE ALARM SOLUTIONS
DAILY USER´S MANUAL
EBL128 VERSION 2.2.X

DOCUMENT INFORMATION
DOCUMENT NAME:
DAILY USER´S MANUAL –EBL128 VERSION 2.2.X
DOCUMENT NUMBER:
MEW01786
DATE OF ISSUE:
2015-01-19
REVISION
1
DATE OF REVISION:
2015-03-30

TABLE OF CONTENTS
1. INTRODUCTION............................................................................................................ 3
2. DESCRIPTION OF THE FRONT.................................................................................... 4
2.1. LED INDICATORS......................................................................................................................... 5
2.2. PUSH BUTTONS........................................................................................................................... 6
2.3. DISPLAY........................................................................................................................................ 6
3. ACCESS LEVELS.......................................................................................................... 7
4. LOG ON TO THE CONTROL UNIT (C.I.E.) ................................................................... 7
4.1. HOW TO LOG ON ......................................................................................................................... 7
5. NAVIGATION / GENERAL PROCEDURES ................................................................... 8
6. PERFORM MONTHLY TEST (H1)................................................................................. 9
7. DISABLE OR RE-ENABLE (H2)................................................................................... 10
7.1. SUB MENU LIST (B1 –B11)........................................................................................................ 10
8. SET CALENDER AND CLOCK (H3) ............................................................................ 12
9. PRESENT SYSTEM STATUS (H4).............................................................................. 13
9.1. SUB MENU LIST (U1 –U8) ......................................................................................................... 13
10. FAULT ACKNOWLEDGE (H6) ................................................................................. 14
11. PERFORM ZONE TEST (H7) ................................................................................... 15
12. INTERLOCKING OUTPUTS AND INPUTS (H9)....................................................... 16
12.1. SUB MENU LIST (C1 –C5) ......................................................................................................... 16
13. CHANGE PASSWORD (H10)................................................................................... 16

3
DAILY USER´S MANUAL •EBL128 VERSION 2.2.X •DOCUMENT NUMBER: MEW01786 •REVISION: 1
1. INTRODUCTION
This document is intended to be used for the daily duties like disablements / re-enablements, zone tests,
and so on in the EBL128 system.
Due to continual development and improvement different S/W versions can be found. This document is
valid for EBL128 S/W version 2.2.x.
The document describes the main menus and the sub menus valid for access level "Building officer".

4
DAILY USER´S MANUAL •EBL128 VERSION 2.2.X •DOCUMENT NUMBER: MEW01786 •REVISION: 1
2. DESCRIPTION OF THE FRONT
YYYY-MM-DD *** EBL128 *** hh:mm [i]
User programmable information text.

5
DAILY USER´S MANUAL •EBL128 VERSION 2.2.X •DOCUMENT NUMBER: MEW01786 •REVISION: 1
2.1. LED INDICATORS
See reference picture on page 4.
1
Fire
Fire alarms.
2
Alarms queued
More than one alarm point / zone have activated fire alarm.
3
Extinguishing
Output(s) for extinguishing equipment activated.
4
Ventilation
Output(s) for fire/smoke ventilation equipment activated.
5
Fire brigade tx
Output "Fire alarm" for fire brigade tx (routing equipment) activated.
6
Operation
The c.i.e. is powered via the rectifier and/or the battery.
7
General fault
Fault(s) in the system.
8
Disablements
Disablement(s) in the system.
9
Fault tx activated
Not acknowledged fault(s):
Output "Fault condition" for fault tx (routing equipment) is activated.
10
Sevice
One or more sensors have reached the service level. See menu H4/U4.
11
Alarm devices
Steady light: Output(s) type "Alarm device" are disabled.
Flashing light: Output(s) type "Alarm device" have generated fault(s).
12
Fire brigade tx
Steady light: Output(s) for "Routing equipment" disabled via menu H2/B3 or
B9 or via open door.
Flashing light: Routing equipment power supply outputs or supervised
outputs of type "Routing equipment" have generated fault(s) or the c.i.e.
has lost contact with these outputs.
13
System fault
EBL128 is not running because of:
S/W fault
CPU fault
Memory fault
C.i.e. restart (fault code ≠ 00 / 03).
14
Fire brigade tx delay
The Alert Annunciation function is enabled.
15
Test mode
Zones are in "test mode".
16
Door open
The door is open in the EBL 128 or an external FBP in the system.

6
DAILY USER´S MANUAL •EBL128 VERSION 2.2.X •DOCUMENT NUMBER: MEW01786 •REVISION: 1
2.2. PUSH BUTTONS
See reference picture on page 4.
17
Fault acknowledge
Used to acknowledge the faults shown in menu H6. Also used to
acknowledge SERVICE signal, see menu H8/S4.
18
Paper feed
Not used in EBL128.
19
Access
Used to log on and get access to the menu.
20
Return
Used to stop input of data, leave a menu ("one step up") and to log off.
21
C
Used to clear /delete just written data.
22
Key pad
Numeric key pad for the digits 0-9.
23
A
Used to accept / select a menu or input of data.
24
Left / right keys
Used to move the cursor in a menu.
25
Up / down keys
Used to scroll between the menus.
26
Alarms queued
Used when LEDs "Alarms queued" are lit. Scroll through the queued alarm
points or zone addresses.
27
Evacuate / Test LED
Used to activate all the sounders or test LED. (Option, only available for
some countries and conventions.)
28
Reset
Used to reset the fire alarms. Has to be pressed for > 0.5 sec.
29
Silence Alarm devices
Used to silence the alarm devices.
May be configured to disable alarm devices.
30
Silence buzzer
Used to silence the buzzer in the EBL 128 when it is sounding.
2.3. DISPLAY
See reference picture on page 4.
31
Display
This is the information the display will show in normal operation state.
The user programmable information text is created via EBLWin.
In normal operation and in quiescent state, the LCD-backlight will
be turned off.
As soon as any other information is shown in the display, the
backlight is turned on.

7
DAILY USER´S MANUAL •EBL128 VERSION 2.2.X •DOCUMENT NUMBER: MEW01786 •REVISION: 1
3. ACCESS LEVELS
INFORMATION ONLY
BUILDING OFFICER
SERVICE PERSONNEL
H4 Present system status
H1 Perform monthly test
H1 Perform monthly test
H6 Display faults
H2 Disable or re-enable
H2 Disable or re-enable
H9 Interlocking outputs and inputs
H3 Set calendar and clock
H3 Set calendar and clock
H10 Change password
H4 Present system status
H4 Present system status
H6 Fault acknowledge
H5 Service
H7 Perform zone test
H6 FAULT Acknowledge
H9 Interlocking outputs and inputs
H7 Perform zone test
H10 Change password
H8 Maintenance
H9 Interlocking outputs and inputs
Described in this document
H10 Change password
4. LOG ON TO THE CONTROL UNIT (C.I.E.)
USER NAME
Up to ten users, 0 to 9 may be programmed. By default at delivery, three users are available:
0 = Information only
1 = Building officer
2 = Service personnel
PASSWORD
Each user has a password for an access level, for example. "Information only", "Building officer" or "Service
personnel".
4.1. HOW TO LOG ON
a) Open the door. Press the button “Access”.
b) On the keypad, press 0, 1, 2 - - 8 or 9 to select a user. Press “A”.
c) Type the password for that user. (Six digits. * * * * * *)
After typing a correct password, the first option of the available menus will be displayed. This is a list in
which you can scroll.
For "0", Information only, no password is required.

8
DAILY USER´S MANUAL •EBL128 VERSION 2.2.X •DOCUMENT NUMBER: MEW01786 •REVISION: 1
5. NAVIGATION / GENERAL PROCEDURES
Scroll in lists or menus with .
Press to toggle between different choices.
The letter 'L' in the lower right corner indicates that this is list in which you can scroll with .
Press “A” to select / accept.
Press the digits on the numeric pad to choose a menu or enter data.
If an operation is completed successfully, the display will normally show a message, for example
"Output xx disabled".
If an operation has failed, the information will be "Operation failed".
To leave a menu and step upward in the menu system, press “Return”.
To logout, close the door.

9
DAILY USER´S MANUAL •EBL128 VERSION 2.2.X •DOCUMENT NUMBER: MEW01786 •REVISION: 1
6. PERFORM MONTHLY TEST (H1)
a) Log on to the c.i.e.
b) Press “A”.
c) Check that all LEDs light up.
d) Press “A”. The c.i.e. buzzer sounds, all the dots in the display are shown and all LEDs on the front
are turned on.
e) Press “A”. Up to four zones can be set in test mode. Use the keypad to type the zone numbers.
f) Press “A”.
g) Perform the test.
h) To end the test, press “A”.
If the routing equipment shall not be tested, the monthly test is completed. Press “A”.
If the routing equipment shall be tested,press “1”. To start the test press "A".
Started test is indicated by LED "Fault tx activated" and after 30 seconds also LED "Fire brigade tx".
After 60 seconds in total, the routing equipment test is ended and the LEDs are turned off. Press "A".

10
DAILY USER´S MANUAL •EBL128 VERSION 2.2.X •DOCUMENT NUMBER: MEW01786 •REVISION: 1
7. DISABLE OR RE-ENABLE (H2)
a) Log on to the c.i.e.
b) Navigate to menu H2.
c) Press "A". The sub menu consists of a list (B1 - B11) in which you can scroll. B1 is displayed.
d) Select a sub menu and press “A”.
7.1. SUB MENU LIST (B1 –B11)
B1
Disable zone
Use the keypad to type the zone number (01-99). Press "A".
If "Automatically re-enablement" shall be used. Press “1”, insert time
(hh:mm). Press “A”.
B2
Disable zone-address
Use the keypad to type the zone number (01-99) and address (01-
99). Press "A".
If "Automatically re-enablement" shall be used. Press “1”, insert time
(hh:mm). Press “A”.
B3
Disable output
Use the keypad to select type of output:
- 0 = Loop unit output.
- 1 = C.i.e. output S0 or S1.
- 2 = C.i.e. output R0.
- 3 = C.i.e. expansion board output.
Press "A".
Depending on the selected type, use the keypad to type additional
data:
- 0: Output number (0-2) and COM loop (technical) address.
- 1: Output (S) number 0-1.
- 2: Output (R) number 0.
- 3: Output number (0-7) and expansion board number (0-3).
Press "A".
B4
Disable all control, ventilation,
exting or interlocking outputs
Use the keypad to select type of output:
- 0=Outputs type Control (not control neutral).
- 1=Outputs type Ventilation.
- 2=Outputs type Extinguishing.
- 3=Output type Interlocking.
Press "A".
B5
Re-enable zone
Select a zone.
To re-enable the selected zone press "A".
Continued

11
DAILY USER´S MANUAL •EBL128 VERSION 2.2.X •DOCUMENT NUMBER: MEW01786 •REVISION: 1
Continued
B6
Re-enable zone-address
Select an alarm point (zone-address).
To re-enable the selected alarm point press "A".
B7
Re-enable output
Only disabled types will be shown.Use the keypad to select type of
output:
- 0 = Loop unit output.
- 1 = C.i.e. output S0 or S1.
- 2 = C.i.e. output R0.
- 3 = C.i.e. expansion board output.
Press "A".
Select the output to re-enable. Press "A".
B8
Re-enable all control,
ventilation, exting or
interlocking outputs
Only disabled types will be shown.Use the keypad to select type of
output:
- 0 = Outputs type Control.
- 1 = Outputs type Ventilation.
- 2 = Outputs type Extinguishing.
- 3 = Output type Interlocking.
Press "A".
B9
Disable / re-enable alarm
devices
Select “Alarm devices in normal condition”or “Alarm devices
disabled”.
Press "A". The status is changed.
B10
Disable / re-enable outputs
for routing equipment
The actual status for the output FIRE and FAULT respectively will be
shown. Use the keypad to select:
- 1 = enabled or
- 0 = disabled for the output respectively.
Step right / left with the arrow keys.
Press "A". The status is changed.
B11
Disable / re-enable alert
annunciation function
“Alert annunciation function is in normal operation”or “Alert
annunciation function turned off”will be shown.
Press "A". The status is changed.
The AA function will stay disabled until re-enabled again via this
menu.
NOTE! Disabled Alert Annunciation function is indicated by LED
"Fault / Disablements Fire brigade tx delay" turned off.

12
DAILY USER´S MANUAL •EBL128 VERSION 2.2.X •DOCUMENT NUMBER: MEW01786 •REVISION: 1
8. SET CALENDER AND CLOCK (H3)
a) Log on to the c.i.e.
b) Navigate to menu H3.
c) Press "A". Depending on if it is the date, time and/or the day that shall be set,
press and to highlight it.
d) Use the keypad to enter new values. Press "A".
NOTE! To exit the menu without making any changes, press “Return”.

13
DAILY USER´S MANUAL •EBL128 VERSION 2.2.X •DOCUMENT NUMBER: MEW01786 •REVISION: 1
9. PRESENT SYSTEM STATUS (H4)
Information only.
a) Log on to the c.i.e.
b) Navigate to menu H4.
c) Press "A". The sub menu consists of a list (U1 - U8) in which you can scroll. U1 is displayed.
d) Select a sub menu and press “A”.
9.1. SUB MENU LIST (U1 –U8)
U1
Disablement
Disablements, except "disablements by time channel", are
displayed.
Indicated by LED "Disablements".
U2
Disablement by time channel
Only "disablements by time channel", are displayed.
Indicated by LED "Disablements", also the LEDs "Fault /
Disablements Alarm devices" and/or "Fire brigade tx".
U3
Sensor values
Use the keypad to specify the "Start sensor".
The default zone-address 00-00 can be used.
Press "A". This is a list in which you can scroll.
NOTE! For most detectors additional information can be shown by
using .
U4
Sensors activating service
signal
Indicated by LED "Service".
NOTE! Service signal is acknowledged via menu H8/S2, which
require log on with a password for access level "Service
personnel".
U5
Technical warning
If one or more technical warnings are activated in the system, the
technical warning symbol [i] is shown.
U6
Event log
Use the keypad to select event log:
- 0 = Alarm.
- 1 = Interlocking.
- 2 = General.
Press "A". This is a list in which you can scroll.
U7
Version and alarm counter
- Version: The EBL128 software / firmware version.
- Alarm counter The alarm counter is increased with "1" every time
the c.i.e. enters the real "fire alarm condition".

14
DAILY USER´S MANUAL •EBL128 VERSION 2.2.X •DOCUMENT NUMBER: MEW01786 •REVISION: 1
10. FAULT ACKNOWLEDGE (H6)
LED "Fault tx activated" on the front is indicating that the output for Fault condition routing equipment is
activated. The LED will be turned off when all faults are acknowledged.
LED "General fault" on the front is indicating that not all faults are acknowledged and corrected.
No status info. = not corrected / serviced and not acknowledged fault.
Acknowledged = not corrected / serviced but acknowledged fault.
Serviced = corrected / serviced but not acknowledged fault.
a) Log on to the c.i.e.
b) Navigate to menu H6.
c) Press "A". A list will be displayed, in which you can scroll. The most recent fault is on top of the list.
d) Scroll with and or press for more information.
e) To acknowledge the fault shown in the display, press the button "Fault acknowledge".
NOTE! A fault that is both serviced and acknowledged will disappear from the list.

15
DAILY USER´S MANUAL •EBL128 VERSION 2.2.X •DOCUMENT NUMBER: MEW01786 •REVISION: 1
11. PERFORM ZONE TEST (H7)
Up to 99 zones can be set in test mode, which is indicated by the LED "Test mode" on the front. After one
hour without any testing activity, the test mode will be automatically ended. Valid for each zone respectively.
No outputs will be activated except the fire door outputs. The test mode alarm will be automatically reset
after approximately 10 seconds.
a) Log on to the c.i.e.
b) Navigate to menu H7.
c) Press "A". The sub menu "Set zone in test mode D1" opens.
d) Press "A". Use the keypad to type a zone number (01-99).
e) Press "A". The zone is now in test mode.
f) If more zones shall be set in test mode, repeat procedure c) to e).
g) Perform the testing. To end the test mode for one zone press .
END TEST MODE
a) Open the sub menu D1 as described above.
b) Press to open the sub menu "End zone in test mode D2".
c) Press "A".
d) L = this is a list in which you can scroll. Select the zone for which the test mode shall be ended.
e) Press "A".
f) The next zone in the list will be shown. End the test mode like above.

16
DAILY USER´S MANUAL •EBL128 VERSION 2.2.X •DOCUMENT NUMBER: MEW01786 •REVISION: 1
12. INTERLOCKING OUTPUTS AND INPUTS (H9)
a) Log on to the c.i.e.
b) Navigate to menu H9.
c) Press "A". The sub menu consists of a list (C1 - C5) in which you can scroll. C1 is displayed.
d) Select a sub menu and press “A”.
12.1. SUB MENU LIST (C1 –C5)
C1
Activated interlocking outputs /
inputs
This is a list in which you can scroll. Read only.
C2
Activate interlocking output
Use the keypad to specify Area –Point (AA and PP) for the
interlocking output to be activated.
Press "A". The status is changed.
C3
Reset interlocking output
This is a list in which you can scroll. Select the Area –Point for
the interlocking output to be reset.
Press "A" The status is changed.
NOTE! For the following the output must be reset via this menu:
- Interlocking output activated via its control expression and with
latching output selected in EBLWin.
- Interlocking output activated via menu C2.
C4
Disable interlocking output
Press "A". Use the keypad to specify Area –Point (AA and PP)
for the interlocking output to be disabled.
Press "A". The status is changed.
C5
Re-enable interlocking output
This is a list in which you can scroll. Select the Area –Point for
the interlocking output to be re-enabled.
Press "A". The status is changed.
13. CHANGE PASSWORD (H10)
You can only change the password for the user that is currently logged on to the control unit.
a) Log on to the c.i.e.
b) Navigate to menu H10.
c) Press "A". The user that is currently logged on to the control unit is shown.
d) Use the keypad to type the old password.
e) Type the new Password. (Six digits. * * * * * *)
f) Verify the new password.

This product has been successfully tested
to the highest standards, ensuring high
quality and reliable fire alarm solutions.
Panasonic Eco Solutions Nordic AB
Jungmansgatan 12
SE-211 19 Malmö
Sweden
Tel: [phone]
Fax: [phone]
E-mail: [email protected]sonic.com
Internet: http://pesn.panasonic.se