Panasonic SB-W680P User manual

ORDERNO. MD0412603C7
A6
Speaker System
SB-W680P
Colour
(S)... Silver Type
SPECIFICATIONS
Specification
1
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

Type 1way, 1speaker system (Bass
reflex)
Speaker unit(s) Impedance 4
Subwoofer 17 cm (6-3/4”) conetype
Input power (IEC) 220 W(Max)
Output sound pressure 86 dB/W(1.0m)
Frequencyrange 35 Hz - 500 Hz (-16 dB)
50 Hz - 250 Hz (-10 dB)
Dimensions(WxH xD) 270 mm x287 mm x283 mm
(10-5/8” X 11-5/16” X 11-5/32”)
Mass 4.1kg(9lbs)
Notes :
1. Specificationsare subject tochangewithout notice.
2. Mass and dimensionsare approximate.
3. Thelabels“HIGH” and “LOW” on therear of thespeakers
refer toHigh frequencyand Lowfrequency.
System : SC-HT680PC-S MusicCenter : SA-HT680PC-S
Front Speaker : SB-HT680P-S
Subwoofer : SB-W680P-S
System : SC-HT680P-S MusicCenter : SA-HT680P-S
Front Speaker : SB-HT680P-S
Subwoofer : SB-W680P-S
System : SC-HT680PL-S MusicCenter : SA-HT680PL-S
Front Speaker : SB-HT680P-S
Subwoofer : SB-W680P-S
2004 Matsushita ElectricIndustrial Co. Ltd.. All rights reserved.
Unauthorized copying and distribution isaviolation of law.
1. Disassembly of the Speaker
1.1. Disassemblyof the Front Panel Assembly
2
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

Step1 : Slot a steel ruleras arrowshowntomake gap / allowance betweenthe Front Panel
Assemblyand the SpeakerCabinet Assembly.
Step2 : Slot a piece of wood chipblock withthe steel rulerabove it as arrowshown.
Step3 : Use the screwdrivertoslot intothe holes and slightlylift up the Front Panel Assembly
as arrowshown. Ensure that the screwdriveris above the wood chipblock whendoing this
process.
3
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

Step4 : Pull the Front Panel Assemblyup toremove as arrowshown.
1.2. Disassemblyof the Subwoofer
Repeat step1 tostep4 initem1.1.
Step1 : Remove all fourscrews fromthe subwoofer.
4
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

Step2 : Remove the wires (+) white and (-) blue fromsubwoofer.
2. Connection of the Speaker Cables
-Besure to connect speaker cables before connecting the AC
power supplycord.
-The load impedance of anyspeaker used with thisunitmust be 4 .
-Besure to connect the cablefrom the right speaker to the right
terminal and the cablefrom the left speaker to the left terminal.
1. Stripoff the outer covering, and twist the center conductor. Make
sure the bare ends of the wires are not unravelled. (Iftheyare,
twist them tight again.)
2. Insert the wire to the rear panel of the unitand close the lever.
5
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

Notes :
-To prevent damage to circuitry, never short-circuitpositive (+)and
negative (-) speaker wires.
-Besure to connect onlypositive (white) wires to positive (+)
terminalsand negative (blue) wires to negative (-) terminals.
3. Connection of the Speaker Wiring
4. Cabinet Parts Location
6
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

5. Replacement Parts List
Notes :
-Important safetynotice :
When replacing anyof these components, be sure to use only
manufacturer’sspecified parts showninthe parts list.
-[M] markings inthe Remarks columns indicates parts supplied by
PAVCSG.
Ref. No. PartNo. PartName& Description Remarks
CABINETAND CHASSIS
1RFKHBW680P-S SPK CABINETASS’Y [M]
1-1 RMQX0083-H LEG BASE [M]
1-2 XTB4+14AFJ SCREW [M]
1-3 RKAX0019-K LEG CUSHION [M]
2RYPX0092 FRONTPANEL ASS’Y [M]
3RMQ0705 EVAPACKING [M]
4RGNX0261-K SPEC LABEL [M]
PACKING MATERIALS
P1 RPNX0298 POLYFOAM [M]
P2 RPFX0106 MIRAMATBAG [M]
SPEAKER
SP1 EAST17PL22A6 WOOFER [M]
6. Packaging
7
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

FLE0412W/S
8
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com