Panasonic SB-MAX500LMK User manual

© Panasonic Corporation 2012, All rights reserved.
Unauthorized copying and distribution is a violation of
law.
PMX1302002CE
Speaker System
Model No. SB-MAX500LMK
Product Color : (K)... Black Type
TABLE OF CONTENTS
1 Service Navigation
1.1. Speaker System Information (SB-
MAX500LMK)
1.2. Speakers Setup
2 Specifications
3Disassembly and Assembly Instructions
3.1. Disassembly of Upper Front Panel Assembly
3.2. Disassembly of Tweeter Speaker (SP1)
3.3.Disassembly of Full Range Speaker (SP4)
3.4.Disassembly of Full Range Speaker (SP3)
3.5. Disassembly of Lower Front Panel Assembly
3.6. Disassembly of Woofer Speaker (SP2)
3.7. Disassembly of Lighting Wire P.C.B.
Assembly
3.8.Replacement of Speaker Connector Housing
(For SB-MAX500LMK)
3.9.Replacement of Speaker Connector Housing
(For SB-MAX500LMK)
4 Wiring Connection Diagram
4.1. Front Speakers (SB-MAX500PHK)
5 Exploded View and Replacement Parts List
5.1. Front Speakers (SB-MAX500LMK) Cabinet
Parts Location
5.2. Packaging
5.3. Replacement Parts List
SB-MAX500

1 Service Navigation
1.1. Speaker System Information (SB-MAX500LMK)
SB-MAX500LMK is use for the following models:
SC-MAX500LMK
1.2. Speakers Setup
Conecte los bafles.
Conecte los cables del bafle a las terminales del mismo color.
LOW LOW LOW LOWHIGH HIGH
MID MID
(8 ) (8 ) (5 )(4 )(5 )(4 )

2 Specifications
Notes:
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum ana-
lyzer.
Sección de bafles
Tipo Sistema de 4 bocinas de 4 vías
(reflejo de sonidos graves)
Bocina(s)
Super Woofer (bajo) Tipo cónico de 38 cm
Super Woofer (medio bajo) Tipo cónico de 20 cm
Woofer Tipo cónico de 10 cm
Bocina para agudos Tipo cónico de 6 cm
Impedancia 5 Ω(alto), 4 Ω(medio bajo), 8 Ω(bajo)
Presión acústica de salida 88 dB/W (1 m)
Gama de frecuencias 38 Hz a 23 kHz (–16 dB)
44 Hz a 18 kHz (–10 dB)
Dimensiones (An x Al x Prf)
558 mm x 796 mm x 525 mm
Peso 31,4 kg

3 Disassembly and Assembly Instructions
Caution Note:
• This section describes procedures for checking the operation and replacing the main components.
• For reassembly after operation checks or replacement, reverse the respective procedures.
• Special reassembly procedures are described only when required.
• Before carrying out the disassembly process, please ensure all the safety precautions & procedures are followed.
• During the disassembly and/or assembly process, please handle with care as there may be chassis components with sharp
edges.
• During replacement of component parts, please refer to the section of “Replacement Parts List” as described in the service man-
ual.
• Select items from the following indexes when disassembly or replacement are required.
Front Speakers (SB-MAX500LMK)
• Disassembly of Upper Front Panel Assembly
• Disassembly of Tweeter Speaker (SP1)
• Disassembly of Full Range Speaker (SP4)
• Disassembly of Full Range Speaker (SP3)
• Disassembly of Lower Front Panel Assembly
• Disassembly of Woofer Speaker (SP2)
• Disassembly of Lighting Wire P.C.B. Assembly

3.1. Disassembly of Front
Panel Assembly
Step 1 : Remove 2 screws.
Step 2 : Remove Corner Guard.
Step 3 : Remove 2 screws.
Step 4 : Remove Corner Guard.

El proceso que se realizara para el desensamble podrá aplicarse, tanto para el bafle derecho como para el izquierdo de igual forma.
1.- Identifique el bafle dañado que deberá ser reparado. Y prepare la 2.- Para mayor facilidad en el proceso coloque el panel en forma horizontal.
.lenaplanatejuseuqselatnorfsollinrotsoleriteretnemroiretsopY.osecorplearapaduyaedárivreseleuqatneimarreh
3.- Retire los Corner Guard frontales e identifique los puntos de sujeción 4.- Inserte la herramienta comenzando por las cavidades que quedaron al
entre el panel y el bafle para comenzar el desprendimiento. descubierto después de retirar los corner guard y comience a hacer palanca
hacia la parte superior poco a poco para comenzar a desprender las guias que
sujetan al panel como se muestra en las figuras (Cuatro esquinas, una a la vez).
5.- Una vez que el panel comience a desprenderce paulatinamente, 6.- Una vez desprendido el panel desconecte los cables de el Tweeter y de luz.
podra insertar el herramental por los nuevos puntos abiertos y poder
desprender mas facil el panel como se muestra en las figuras.
12
Cubra la herramienta con
material suave para evitar
dañar la madera y el panel
(preferentemente tela)
50cm min
6
p
cs
Coloque el bafle de forma horizontal pero montado
sobre unos soportes para evitar que el cable sea
dañado y/o la parte posterior de el bafle se dañe.
Protector (Tela)
La herramienta de ayuda
puede ser de cualquier
material, siempre y
cuando sea resistente
para el proceso a realizar.
2 Tornillos por cada
Corner Guard.
Proceda a retirar los tornillos.
Son 10 los puntos de sujeción que
tiene el panel con el Bafle como se
muestra en la figura.
Repita estos procesos varias
veces hasta que el panel se
comience a desprender.
1. No intente desprender el
panel en una sola ejecución,
ya que esto podría ocasionar
algún daño en este (Marca de
estrés o fractura en las guías).
2. Al insertar la herramienta
para hacer palanca, cuide los
puntos de apoyo para evitar
daños en las bocinas.
Parte superior, area
de bocina de 20cm
Partes laterales, area de
Tweeter
y
bocina de 10cm
Todos los procesos deberán ser repetitivos y con fuerza
moderada hasta poder retirar el panel sin dañarlo.
Desconecte el
Tweeter
Desconecte el cable
de luz conforme a
los siguientes pasos.
1. Retire la
protección.
2. Separe los
conectores quitando
el seguro.
Finalmente ya retirado el
panel, proceda a realizar la
reparación pertinente.
8mm max
10mm max
Rectangualr o Circular

137.4
122.4
29.5
185.4
181.5
271.5
80.9
80.9
327.7
173.1
80.9
Nota: Unidades dadas en mm (solo de referencia)

3.2. Disassembly of Tweeter
Speaker (SP1)
• Refer to “Disassembly of Front Panel Assembly”.
Step 1 : Remove 2 screws.
Step 2 : Remove the Tweeter Speaker (SP1).
3.3. Disassembly of Full Range
Speaker (SP4)
• Refer to “Disassembly of Front Panel Assembly”.
Step 1 : Remove 4 screws.
Step 2 : Slightly lift up Full Range Speaker (SP4) as shown.
Step 3 : Detach the (+) and (-) speaker wires.

Step 4 : Remove the Full Range Speaker (SP4). 3.4. Disassembly of Full Range
Speaker (SP3)
• Refer to “Disassembly of Front Panel Assembly”.
Step 1 : Remove 4 screws.
Step 2 : Slightly lift up Full Range Speaker (SP3) as shown.
Step 3 : Detach the (+) and (-) speaker wires.

Step 4 : Remove the Full Range Speaker (SP3).

3.6. Disassembly of Woofer
Speaker (SP2)
•Refer to “Disassembly of Upper Front Panel Assembly”.
•Refer to “Disassembly of Front Ornament Assembly”.
Step 1 : Remove 8 screws.
Step 2 : Slightly lift up Woofer Speaker (SP2) as shown.
Step 3 : Detach the (+) and (-) speaker wires.

Step 4 : Remove the Woofer Speaker (SP2). 3.7. Disassembly of Lighting Wire
P.C.B. Assembly
• Refer to “Disassembly of Front Panel Assembly”.
• Refer to “Disassembly of Front Ornament Assembly”.
Step 1 : Remove 14 screws.
Step 2 : Remove 4 screws.

Step 3 : Slightly lift Front Ornament Assembly.
Step 4 : Release the 4P wire from the hole of Front
Panel Assembly.
Caution : During assembling, inserted the 4P wire into the
opening of Front Panel Assembly as diagram
shown.
Step 5 : Remove 4 screws.
Step 6 : Release the 4P wire from the slots.
Caution : During assembling, ensure that the 4P wire is
properly inserted into the slot.
Step 7 : Remove Lighting Wire P.C.B. Assembly.

3.8. Replacement of Speaker Connector Housing (For SB-MAX500LMK)
3.8.1. Disassembly of Speaker Connector Housing
Step 1: Insert a paper clip & push the Wire terminals outwards.
Step 2: Detach the (+) and (-) speaker wire.
3.8.2. Assembly of Speaker Connector
Housing
Step 1: Slightly lift up the wire terminals approximately 45°as
shown.
Step 2: Insert the (+) speaker wire into the (+) hole of the
Speaker Connector Housing.
Step 3: Push in the speaker wire until hear the “click” sound.
Step 4: Insert the (-) speaker wire into the (-) hole of the
speaker connector housing.
Step 5: Push in the speaker wire until hear the “click” sound.
Step 6: Pull both speaker wires gently to ensure they lock-in
firmly.
Note: Repeat these procedures if the speaker wires come out.

3.9. Replacement of Speaker Connector Housing (For SB-MAX500LMK)
For Speaker wire connection, please refer to 1.2. Speaker setup
3.9.1. Disassembly of Speaker Connector Housing
Step 1: Insert a paper clip & push the Wire terminals outwards.
Step 2: Detach the (+) and (-) speaker wire.
3.9.2. Assembly Disassembly of Speaker
Connector Housing
Step 1: Slightly lift up the wire terminals approximately 45°as
shown.
Step 2: Insert the (+) speaker wire into the (+) hole of the
Speaker Connector Housing.
Step 3: Push in the speaker wire until hear the “click” sound.
Step 4: Insert the (-) speaker wire into the (-) hole of the
speaker connector housing.
Step 5: Push in the speaker wire until hear the “click” sound.
Step 6: Pull both speaker wires gently to ensure they lock-in
firmly.
Note: Repeat these procedures if the speaker wires come out.

4 Wiring Connection Diagram
4.1. Front Speakers (SB-MAX500LMK)

5 Exploded View and Replacement Parts List
5.1. Front Speakers (SB-MAX500LMK) Cabinet Parts Location
SP4
SP3
SP2
SP1
24
23
23
22
22
21
20
19
19
19
19
20
20
20
18 18
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17 17
17
17
17 17
16 16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16 16
16
16
16
16
16
16
16
16
16
16
16
16
15
15
15
15
14-2
14-1
14
13
12
11
5
5
9
8
7
7
7
7
6
6
6
6
6
6
6
6
18
18
4
3
ZJ6109
ZJ6104
ZJ6110
(LIGHTING
P.C.B.)
(LIGHTING
P.C.B.)
1
2
c
a
b
h
i
h
i
d
e
d
e
g
f
gf
a
b
c
123456789
A
B
C
D
E
F
G
H
10 11 12 13
SB-MAX500LMK
CABINET DRAWINGS

5.2. Packaging
SB-MAX500LMK
SB-MAX500LMK
P3
P3
*P2
*P2 *P2
*P2
FRONT
RPGM0280-2
P1
123456789
A
B
C
D
E
F
G
H
10 11 12 13
*P2
POLYFOAM RPNM0259T (TOP)
POLYFOAM RPNM0259B (BOTTOM)
SB-MAX500LMK
PACKAGING DRAWINGS

5.3. Replacement Parts List
5.3.1. Front Speakers (SB-MAX500LMK)
Safety Ref. No.Part No. Part Name&
Description
QtyRemarks
CABINET &CHAS-
SIS
1REE1737 LIGHTING WIRE
PCB ASS’Y
1
2RGK2430-SL FRONT ORNAMENT 1
3RGL0781-QL LIGHTING PIECE 1
4RQLM0445 SPEC LABEL (L) 1
4RQLM0444 SPEC LABEL (R) 1
5RYPM0317 FRONT PANEL 1
6RGQ0708-KL CORNER GUARD 8
7RKAX0042-KLEG RUBBER 4
8RMQ0819EVA PACKING 1
9RMQM0175 EVA PACKING 1
11 RMQM0174 EVA PACKING 1
12 RYQ1114-KL NET FRAMEASSY
(WOOFER)
1
13 RYPM0318 TWEETER HOLDER
ASSY
1
14 RKPM0152 WOODEN BOX ASSY
(L)
1
14 RKPM0151 WOODEN BOX ASSY
(R)
1
14-1 K1MY04A00003 4P SPK CONNEC-
TOR HOUSING
WHITE (L)
1
14-1 K1MY04A00004 4P SPK CONNEC-
TOR HOUSING RED
(R)
1
14-2 KN-MSA-22-02 2P SPK CONNEC-
TOR HOUSINGLF(P8)
WHITE (L)
1
14-2 KN-MSA-22-01 2P SPK CONNEC-
TOR HOUSING REDLF(P8)
(R)
1
15 XTB3+12GFJSCREW 4
16 XTB4+12GFJSCREW 30
17 XTB4+16AFJKSCREW 33
18 XTB4+20AFJKSCREW 4
19 RMQM0188 HIMELON 4
20 RMQM0182 HIMELON 4
21 RMR2103-KL WOOFER SPACER 1
22 RMQM0187 HIMELON 2
23 RMQM0186 HIMELON 2
24 RMQM0189 HIMELON 1
SPEAKERS
SP1 EAS6PH124KTWEETER 1
SP2 L0AA38A00006 WOOFER SPEAKER 1
SP3 L0AA20A00021 SPEAKER 1
SP4 EAS10P661B SPEAKER 1
SafetyRef. No. Part No.Part Name &
Description
Qty Remarks

5.3.2. Packing Materials
SafetyRef. No. Part No.Part Name &
Description
QtyRemarks
PACKING MATERI-
ALS
P1 RPGM0280-2 PACKING CASE 1
P2 RPNM0259T/B POLYFOAM 2
P3 RPFM0064/-R MIRAMAT BAG 2