Panasonic KX-T7030 User manual

Panasonic
Proprietary Telephone for
Electronic Modular Switching System
MODEL NO.
KX-17030
Illustrated Model: White 1
KX-T7030 is compatible with all of the Panasonic Electronic Modular
Switching Systems and can perform most functions within each system.
Please read before use.

Important Safety Instructions
When using your telephone
equipment, basic safety
precautions should always be
followed to reduce the risk of fire,
electric shock and injury to
persons, including the following:
1. Read and understand all
instructions.
2. Follow all warnings and
instructions marked on the
product.
3. Unplug this product from the
wall outlet before cleaning.
Do not use liquid cleaners or
aerosol cleaners. Use a damp
cloth for cleaning.
4. Do not use this product near
water, for example, near a
bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet
basement, or near a
swimming pool.
5. Do not place this product on
an unstable cart, stand, or
table. The product may fall,
causing serious damage to
the product.
6. Slots and openings in the
cabinet and the back or
bottom are provided for
ventilation, to protect it from
overheating, these openings
must not be blocked or
covered. The openings
should never be blocked by
placing the product on the
bed, sofa, rug, or other similar
-1
surface. This product should
never be placed near or over
a radiator or heat register.
This product should not be
placed in a built-in installation
unless proper ventilation is
provided.
7. Do not allow anything to rest
on the telephone cord. Do not
locate this product where the
cord will be abused by
persons walking on it.
8. Do not overload wall outlets
and extension cords as this
can result in the risk of fire or
electric shock.
9. Never push objects of any
kind into this product through
cabinet slots as they may
touch dangerous voltage
points or short out parts that
could result in a risk of fire or
electric shock. Never spill
liquid of any kind on the
product.
10. To reduce the risk of electric
shock, do not disassemble
this product, but take it to a
qualified serviceman when
some service or repair work is
required. Opening or
removing covers may expose
you to dangerous voltages or
other risks. Incorrect
reassembly can cause
electric shock when the
appliance is subsequently
used.

11. Unplug this product from the
wall outlet and refer servicing
to qualified service personnel
under the following conditions:
A. When the power supply
cord or plug is damaged or
frayed.
B. If liquid has been spilled
into the product.
C. If the product has been
exposed to rain or water.
D. If the product does not
operate normally by
following the operating
instructions. Adjust only
those controls, that are
covered by the operating
instructions because
improper adjustment of
other controls may result in
damage and will often
require extensive work by
a qualified technician to
restore the product to
normal operation.
E. If the product has been
dropped or the cabinet has
been damaged.
F. If the product exhibits a
distinct change in
performance.
12. Avoid using a telephone
(other than a cordless type)
during an electrical storm.
There may be a remote risk of
electric shock from lightning.
13. Do not use the telephone to
report a gas leak in the
vicinity of the leak.
SAVE THESE
INSTRUCTIONS
Included accessories
Handset............... one
Telephone line cord . . . . one
Handset cord . . . . . . . . . . . one
Card holder with memory
station card . . . . . . . . . . one
Overlay . . . . . . . . . . . . . . . one
1
-2-

Thank you for purchasing the Panasonic Telephone.
Table of Contents
Important safety instructions ................. .I
Connection ............................... .
Initial setting ............................. .4
Location of controls ........................ .5
Using overlay ............................. .7
Installing the card holder .................... .8
Wall mounting ............................ .9
Important information
....................... 10
Accessory order information .......... Back cover
Connection
Connect as shown.
To the EMSS control
unit
-3-

Initial setting
I-
HANDSET VOLUME Selector:
To adjust the volume level of the handset.
NORMAL: Normal voice
HIGH: Loud voice
RINGER VOLUME Selector:
To adjust the volume level of the ringer.
HIGH: Loud ringer
LOW: Low ringer
OFF: No ringer
VOLUME Control:
To adjust the volume level of the speaker volume.
MAX: Loud voice
MIN: Low voice
MEMORY Switch:
Set to “SET”.
For station programming, set to “PROGRAM”.
HANDSET/HEADSET Selector:
Set to “HANDSET”.
For connecting the headset, set to “HEADSET”.
CONTRAST Selector:
To adjust the contrast of the Liquid Crystal Display.
-4-

Location of controls
---a
-@
-a
--a
2
10
-0
-----a
----@
KX-T7030 is compatible with the Panasonic Electronic Modular
Switching Systems and can perform most functions within each
system.
-5-

@ INTERCOM Button and
Indicator:
Used for making or receiving
an intercom call.
@CONFERENCE Button and
Indicator:
Used for speaking with three
parties at the same time.
@ REDIAL Button:
Redials the last number
dialed.
@ FLASH Button:
Used for sending the hook
flash signal to the CO line.
@ LCD (Liquid Crystal Display)
@ Programmable Feature Buttons:
Dials or accesses the system
feature with one touch.
@ Flexible CO Line Buttons and
Indicators*:
Used for dialing via CO line,
Direct Station Selection, or
Programmable Feature
buttons.
@ Flexible Message Waiting
Button and Indicator*:
Used for Message Waiting,
Direct Station Selection, or
Programmable Feature button.
@ FWD/DND Button and Indicator:
Sets or cancels the Call
Forwarding/Do Not Disturb
feature.
@TRANSFER Button:
Transfers a call to any
extension.
0 PAUSE Button:
Inserts a pause between the
access number and the
phone number.
@IAUTO DIAL/STORE Button
and Indicator:
Used for dialing the system
speed dialing/For storing
functions into memory.
@AUTO ANSWER/MUTE Button
and Indicator:
Used for answering an
intercom call automatically/
For muting your voice in
hands-free mode.
@ISP-PHONE Button and
Indicator:
Used for making or receiving
a call without using the
handset.
@ HOLD Button:
Places a call on hold.
*These functions are limited to the
specified EMSS Control Units.
Refer to the manual.
-6-

Using overlay
When you set the system programming data, the function of the KX-T7030
connected to your EMSS unit will change as follows.
SECRET
47-
+
CLEAR
PAUSE
STORE/AUTO
SELECT
-7-

Installing the card holder
1
Line up the marks (b) on
the card holder and ones on
the slide rails of the unit.
2
Push the two shaded
portions slightly and insert
the edges of the holder
under the slide rails and
then slide down toward
arrow “A”.
Removing the card holder:
Push the card holder toward
arrow “B” while keeping the tip
of the holder pulled toward arrow
“C”.
-8-

Wall mounting
This unit can be mounted on the wall phone plate.
1
Turn the handset hook
upside down.
/
4
Place the stand on the
center of the unit.
2
Remove the attached stand.
5
Mount the unit on the wall
phone plate.
shows UP for WALL.
To temporarily place the handset
down during a conversation, hook
as shown.
f
-9-