Panasonic KX-T7710 User manual

Quick Reference Guide
Model No. KX-T7710
Attention
When using the KX-T7710, keep the following conditions in mind.
If there is any problem, unplug the extension line and connect a known working phone.
If the known working phone operates properly, have the defective phone repaired by a
specified Panasonic Factory Service Centre. If the known working phone does not
operate properly, check the Panasonic KX series Business Telephone System and the
internal extension wiring.
Keep the unit away from heating appliances and electrical noise generating devices such
as fluorescent lamps and motors.
The unit should be kept free of dust, moisture and vibration, and should not be exposed
to direct sunlight.
Do not use benzine, thinner, or any abrasive powder to clean the cabinet. Wipe it with a
soft cloth.
Do not disassemble this product. Dangerous electrical shock could result. The unit
must only be disassembled and repaired by qualified service technicians.
Do not use any handset other than a Panasonic handset.
Never attempt to insert wires, pins, etc, into the vents or other holes of this unit.
When a failure occurs which exposes any internal parts, disconnect the telephone line cord
immediately and return the unit to a service centre.
WARNING:
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR ANY TYPE OF MOISTURE.
THIS HANDSET EARPIECE IS MAGNETISED AND MAY RETAIN SMALL FERROUS
OBJECTS.
Note:
In this manual, the suffix of each model number is omitted.
This Class B digital apparatus complies with Canadian ICES-003.
This product is intended to be connected to Panasonic KX series Business Telephone System.

Off-hook On-hook Feature number Talk
*"Location of Controls" is shown on page 5.
Desired Function Operation
Calling
Redial
One-touch
Dialling
Calling an
operator
Station Speed
Dialling
To an extension To an external party
phone no.
extension no.
To dial
System Speed
Dialling
Making Calls
The REDIAL will dial the last number you called manually.
line access
no.
Press One-touch button.
/
Quick Dialling
quick dial no.
To dial
To dial
Station speed
dial no. (0-9)
System speed dial no.
To store
*The Feature numbers described in this manual are for KX-TD500 or KX-TD816/KX-TD1232.
If a different Panasonic KX series Business Telephone System is connected, please
refer to its manuals.
To store
desired no.
(max., 22 digits)
/
Press One-touch button.
desired no.
(max., 22 digits)
When the Dialled Extension is Busy/No Answer
Receiver
Sender
To call back
Message
Waiting
extension no.
Leave
Cancel
To leave/cancel a notification
Station speed
dial no. (0-9)
Features List
– 2 –
OPER

Desired Function Operation
Holding To retrieve a call at the holding extension
Announce.
dial no.
Holding a call
Transferring
a call
During a Conversation
Paging
Announce.
All groups
Specific group
All external speakers
All groups & external speakers
group no.
To answer a page
Specific external speaker
external speaker no.
external speaker no.
From a telephone speaker
From an external speaker
To page
To lock
To unlock
Useful Features
Useful Features
desired phone no.
Three-party
Conference
During a conversation
Locking your
extension
lock code lock code
lock code
❑
KX-TD500
❑
KX-TD816/KX-TD1232
Features List
– 3 –
❑
KX-TD500
❑
KX-TD816/
KX-TD1232
❑
KX-TD500
❑
KX-TD816/
KX-TD1232

– 4 –
Regarding other operations, please refer to the manuals
for the connected Panasonic KX series Business
Telephone Systems.
Setting Lock/Unlock
desired no.
(max., 22 digits)
You can lock the settings for one-touch buttons and MESSAGE button. [Default: Unlock]
To lock
To unlock
You can change the feature access number for the MESSAGE Button. [Default: 702]
For more detail, refer to the manuals for the connected Panasonic KX series Business
Telephone Systems.
One-touch buttons
Station Speed Dialling
Five One-touch buttons can be used as a One-touch dialling button or to access a feature.
You can store up to 10 Station speed dial numbers.
MESSAGE Button
Confirmation in Programming Mode
When programming, you can confirm your entry by three types of beep sound.
• One long beep: Your entry is accepted.
• Two beeps: Your entry is same as a previous entry.
• Three beeps: Your entry is rejected.
Memory Back Up
If the telephone line is disconnected for more than three days, the stored numbers
for One-touch dialling and Speed dialling will be erased. Please store them again.
Also, the settings for MESSAGE and Flash time will return to the default settings.
selection no.
1: 80 ms, 2: 90 ms, 3: 100 ms,
4: 110 ms, 5: 200 ms, 6: 300 ms,
7: 400 ms, 8: 600 ms
Flash Time
Operations in NORMAL Mode
Before programming the length of Flash time, make sure the position of the Mode
switch lever is "NORMAL". Enter the appropriate selection number for your country.
[Default: 600 ms]

Confirming the Mode
Adjusting the RINGER Volume
Adjust the RINGER volume selector lever (at the bottom of the unit) to
the desired setting. ( – LOW, – MIDDLE, – HIGH)
[Default: MIDDLE]
You can confirm the current mode by the position of the Mode switch
lever (at the bottom of the unit). [Default: NORMAL]
PAUSE: Used to insert a pause when
storing a telephone number.
AUTO: Used for Station Speed dialling.
PROGRAM: Used to enter the
programming mode.
MESSAGE: Used to call back the party who left the message
waiting indication.
Handset Volume Control Buttons: Used to adjust the handset volume.
One-touch Buttons (M1-M5): Used to
access a feature or as a One-touch
dialling button.
FLASH/RECALL: Used to send a flash signal in order to access a
PBX feature (eg., Hold, Transfer, or Three-party Conference).
REDIAL: Used to redial the last dialled number.
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
PBX mode NORMAL mode
Connecting a Communication Device
Telephone Card: Has two sides (NORMAL mode, PBX mode).
DATA PORT
To connect a communication device such as a computer modem
to the telephone line, please use the DATA PORT (at the right
side of the unit). RJ11 modular jack is available.
PBX ModeNORMAL Mode
Message/Ringer Lamp: Flashes when you receive a call or when
someone has left you a message.
One-touch Buttons
(1-8): Used as a One-
touch button which is
set by the Panasonic
KX series Business
Telephone Systems ; you
do not need to program
at your extension.
The KX-T7710 has two modes, NORMAL Mode and Panasonic PBX Mode*.
Please use the corresponding side of the Telephone Card depending on the mode.
*The PBX Mode may not be available depending on the model of the connected Panasonic KX series
Business Telephone Systems.
For more detail, please consult your dealer.
OPER
Location of Controls
– 5 –

Removing the Telephone Card Cover
Telephone
line cord
Wall
mounting
adaptor
12
3
To temporarily
place the handset
down during a
conversation:
Wall Mounting
12
Things You Should Know
– 6 –

– 7 –
Important Information
NOTICE:
This equipment meets the applicable Industry Canada Terminal Equipment Technical
Specifications. This is confirmed by the registration number. The abbreviation, “IC:”, before
the registration number signifies that registration was performed based on a Declaration
of Conformity indicating that Industry Canada technical specifications were met. It does
not imply that Industry Canada approved the equipment.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The equipment must
also be installed using an acceptable method of connection. The customer should be
aware that compliance with the above conditions may not prevent degradation of service
in some situations.
Repairs to certified equipment should be coordinated by a representative designated by
the supplier. Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request the user to
disconnect the equipment.
Users should ensure, for their own protection, that the electrical ground connections of the
power utility, telephone lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas.
Caution:
Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate.
NOTICE:
The Ringer Equivalence Number (REN) assigned to each terminal device provides an
indication of the maximum number of terminals allowed to be connected to a telephone
interface. The termination on an interface may consist of any combination of devices
subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the
devices does not exceed 5.
The Ringer Equivalence Number (REN) of This Unit:
(found on the bottom of the unit).

© 2003 Panasonic Communications Co., Ltd. All Rights Reserved.
Printed in Canada
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, ON L4W2T3
PSQW2023ZA KK0403TT0