Panasonic NA-F42J2T User manual

ORDERNO.MEL0010045C3
Washing Machine
NA-F42J2T / NA-F60H / NA-F5000T
SPECIFICATIONS
Specifications
MODEL NA-F42J2T NA-F60H NA-F5000T
Power Source AC 220V ~ 240V
50 Hz
Dimension Width Depth Height
582 mm 620 mm 870 mm
Water Level Selector Water Load ClothLoad
(StandardizedWater Height 53 litres 49 litres
Amount) Medium 41 litres 37 litres
Low 34 litres 32 litres
Extra Low 18 litres 17 litres
StandardizedWater
Consumption (Normal) 140 litres
Operating Water
Pressure 0.3~ 10 kgf / cm2
(8~ 25 Iitres / min)
Pulsatorr.p.m 120 r.p.m
Spinr.p.m 820 r.p.m
MachineWeight 29 Kg
1

MODEL NA-F42J2T NA-F60H NA-F5000T
Power Consumption
(Motor) Input 320w, Output 160w
SafetySwitch Lidand Unbalance Switch
Buzzer CycleEnd Buzzer, GiveanAlarm
Thermal Protector Motor
Rinse Case Softener
Dispenser 0
BleachInlet 0
Lint Filter 0
AutoPower Off 0
Pressure Hose
FeedValveJoint AUnit
Accessories WashBoard
Service Hose B Unit (0.8m)
Anti-rat protection base
2000 Matsushita ElectricCo., (M) Bhd. All rights reserved.
Unauthorized copying and distribution isaviolation of law.
(CompanyNo. 6100K)
1. FEATURE AND TECHNICAL EXPLANATION
1.1. [The DoubleCascade] Structure and Washability
-Structure of the DoubleCascade
The wash water circulates from the bottom upward and shoot out
of twoopenings like waterfalls.
Spining blades below the tub act as acentrifuge to force water
upward.
2

1.2. Weight Sensor
Sense byinertia movement on pulsatorwhichcreate changes at the capacitorterminals which
give a wave signal. This wave is change tonumberof frequencyand loadweight is judge bythis
numberof pulse.
Fornormal course, strong course before weight, process start without water, the pulsatorwill
turnfor4.2 sec. (left and right) (0.3 sec. ON - 0.4 OFF). During motor“OFF” time it will count the
numberof edges on the pulse and judgement is base on the total accumulation. But, if waterin
the tub is more thanreset level, the waterlevel indication will always go to“High”.
1.3. Fuzzysensor control
Control systembasedon fuzzylogic detects the amount of laundryand indicates the proper
waterlevel and recommendedamount of detergent.
3

4

1.4. Wash Cycle
COURSE SOAK WATER WASH RINSE SPIN
LEVEL TIME CYCLE TIME
Maximum
NORMAL HIGH 15 min. Maximum
Maximum
30 sec. Rinse 8 min.
~
W60 min. MEDIUM cycle
A2 times
S STRONG LOW Minimum Minimum
Maximum
H12 min. 6 min.
~
30 sec.
CMEDIUM Rinse
Approx.
OSPEEDY — 3 min. cycle 3 min.
39
U LOW 20 sec. 3 times
R
S
EMEDIUM Rinse Mild
Approx.
GENTLE — 3 min. cycle 40 sec.
28
LOW 3 times
S
E
LHOME
E 8 min. Rinse Mild
Approx.
5

C DRY — MEDIUM 30 sec. cycle 38 sec.
29
T 2 times
CARE
2. INSTALLATION INSTRUCTION
2.1. Check Installation Location
2.2. Connect supplywater hose
6

(Note)
- Firmlytightenpart B of the faucet joint,
otherwise waterleakage will result.
- Whenthe hose must be reinstalled(afteryou
move, forexample), turnB tothe left until about
4 mm orthe threadbecomes visible, thencarry
out the procedure describedabove.
- The connectorcannot be usedwithan
extension oranall-purpose home faucet. In
these cases, use the CB-J3 faucet (sold
separately). (Leaks will result otherwise.)
2.3. Install the washing machine under alevel sturdyfloor
HOW TO ADUSTTHE HEIGHTOFADJUSTABLE LEG
7

FOR THE CASE OFUNEVEN FLOOR
3. TROUBLESHOOTING GUIDE
Whendiagnosing a problem, because the electronic circuitryis socomplex, sometimes a
condition is mistakenlythought tobe a malfunction whenit is not perform check and
troubleshooting beginning withparts towhichloadis applied, similarlytotroubleshooting for
conventional mechanical circuitry.
Troubleshooting table
8

4. TEST RUNNING WITHOUT WATER
4.1. Method to test running without water.
1. Set the power switch to “OFF”.
2. Press and holdboth the “Reserve and water level”buttons with
one hand.
3. Set the power switch to “ON”.
4. Release your fingers from the buttons and power switch which
you pressed insteps (2) and (3) above.
(Check Acan be carried out inthisstate with your fingers
9

released).
5. Withinthree seconds, press the “Reserve” button one or two
times to set the desired check procedure. (Carryout check Band
C).
Numberof
times
the “Reserve” Check Check
Contents Lampillumination condition Operation
condition
button is
pressed Procedures
0 A -End Signal
-Auto power off.
-Abnormal
signal semister
-When theend buzzer
sounds
times, process lamps
will
neouslyflash on and off
and
will automaticallybe
switched
immediatelyafter
operation
1 B Wash
Operation
Check
-Even ifthereisno water
in
washing operation will
continue
minutes.
-Water flowcan be
changed
level button.
2 C Spin
Operation
Check
-Thespinning operation
will
for fiveminutes.
-Itispossibleto check
lid
operation. Open thelid
slowly,
check.
5. ERROR INDICATION TABLE
- whenthe following indications occurthe buzzerwill sound.
10