Panasonic NA-F80GD User manual

1 SPECIFICATIONS 2
2 SCHEMATIC DIAGRAM 2
2.1. For 3 pin plug 2
2.2. For 2 pin plug 2
3 PRODUCT INFORMATION 3
3.1. Timer type drying function 3
3.2. Use the “ TUB DRY “ function to prevent black mold 4
3.3. Lid lock and release 4
4 CHECK INPUT AND OUTPUT VOLTAGE OF THE PC.BOARD
5
5 OPERATIONS 6
6 DRYING TIPS 7
7 CHECK PRIOR TO START UP 8
8 DISASSEMBLY INSTRUCTIONS AND ADJUSTMENTS 9
©2003 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
NA-F80GD
Product Color : White
9 TEST RUNNING WITHOUT WATER 16
9.1. METHOD TO TEST RUNNING WITHOUT WATER 16
10 LOCATION 19
10.1. LOCATION OF PARTS-A 19
10.2. REPLACEMENT PARTS LIST-A 20
10.3. LOCATION OF PARTS-B 21
10.4. REPLACEMENT PARTS LIST-B 22
10.5. LOCATON OF PARTS-C 23
10.6. REPLACEMENT PARTS LIST-C 24
10.7. LOCATION OF PARTS-D 25
10.8. REPLACEMENT PARTS LIST-D 26
10.9. PACKING PARTS LIST 27
Washing Machine
CONTENTS
Page Page
Order No.HUD0311343C3

2.1. For 3 pin plug
2.2. For 2 pin plug
1 SPECIFICATIONS
Power source AC220V , 230V
50Hz
Spin r/min.
(Clothes load)
830 r/min.
Dimension (Width)599mm (Depth)612mm (Height)1010mm Machine weight 41kg
Water level selector
(standaedized water
amount)
Pulsator washing Centrifugal washing Power consumption
(Motor)
Input Output
67L - 8.0kg 67L - 8.0kg Pulsator 300W 220W
57L - 5.5kg 57L - 8.0kg Centrifugal 300W 100W
49L - 3.5kg 49L - 5.5kg Heater (Dry) 770W
38L - 1.0kg 38L - 1.5kg Safety switch Lid and unbalance switch
22L - 0.3kg 22L - 0.3kg Buzzer Cycle-end buzzer, Give an alarm
Standerdized water
consumption (Normal)
125L Thermal protector Motor
Softener dispenser Providing
Operating Water
pressure
0.03 to 1MPa
(4.3p.s.i to 142p.s.i)
Bleach inlet Providing
Lint filter Providing
Auto power off Providing
Pulsator r/min.
(Clothes load)
130 r/min. Accessories Pressure hose (Inlet hose)
Feed valve joint A
Service hose B unit
2 SCHEMATIC DIAGRAM
2

3.1. Timer type drying function
Below half the height of the stainless steel part of the tub
represents a load of under 3.0kg.
The heater, fan motor and fan case are providing inside of the
panel, and drying function shall be operated by timer control.
Exhaust air including humid air shall be come out from upper
portion of the tub through the exhaust filter.
<Approximate drying time>
Drying capacity Necessary hours
1. 3.0kg Approx. 3 hours
2. 2.0kg Approx. 2-3 hours
3. 1.0kg Approx. 1.5-2 hours
4. 0.5kg Approx. 1-1.5 hours
*Dryed up conditions shall be changed against
atmospheric temperature, humidity and installations.
3 PRODUCT INFORMATION
Dryer capacity 3.0kg
Putting in too many garments will lessen the dryer’s effect and cause wrinkles.
Overfilling (over capacity) indicator
Remaining time indication for drying
It is not possible to indicate remaining time more than 100 min. due to
two digit. therefore, even select more than 2 hours (2 and 3 hours),
“--”mark shall be indicated at start of drying and indicate proper
remaining time from 90 min.
Remaining time shall be decreased on every one minute.
Drying process (Power save course)
3

Drying process (Normal timer course)
3.2. Use the “ TUB DRY “ function to prevent black mold
Activating “Tub Dry” after the wash is complete eliminates the
humidity in the tub that is one cause of black mold. (Activate
once a week)
1. Turn on the power supply
Press DRY to select “Tub Dry”.
2. Close the inner cover and the lid and press START
The washing machine will rotate the tub quickly and blow in hot
air for roughly 30 minutes.
The operation is finished when the buzzer sounds. NOTE ·The occurrence of black mold in the tub depends on the
usage environment.
·Once black mold has formed, activating “Tub Dry” will
not remove it.
3.3. Lid lock and release
4

4 CHECK INPUT AND OUTPUT VOLTAGE OF THE
PC.BOARD
1. Before replace PC.Board, check input and output voltage of the PC.Board.
2. Check range of the test meter.
3. When check output voltage of the PC.Board, set a program of the Washing Machine on the working mode.
4. Incase of measuring the motor circuit, Confirm all of 3 conbinations (Red-Purple, Red- Blue and Blue-Purple) weather normal
conditions or not.
5. Incase of measuring push switch circuit, It shall not be pressed Power-ON button measured AC 220V, And press Power-ON
button once to change AC 0V.
5

5 OPERATIONS
6

6 DRYING TIPS
7

7 CHECK PRIOR TO START UP
8

8 DISASSEMBLY INSTRUCTIONS AND ADJUSTMENTS
PC Board
(Power side)
1Remove the back panel.(4 screws)
2Remove the insulation spacer.(5 pawls)
3Remove the earth wire.(1 screw)
4Remove connectors, and pull the PC Board upward to remove the PC Board
w/components from the body.
5Remove the tip of the lead wire holder by using long nose pliers.
9

PC Board
(Operation
side)
1Open the lid, and remove the panel A packing. After that, remove one screw
mounting the panel face A.
2Slide the panel face A to right to remove.
3Turn the panel face A back side front.
4Remove pawls holding the PC Board.
5Remove 2 connectors from the PC Board.
6Remove the lead wire holder by using the pliers.
Body B 1Open the lid and remove the lid hinge shaft. After that remove the lid.
2Pull out the detergent case B.
3Remove 2 screws mounting the body B. (Bottom portion of the both left and
right of the lid)
4Remove 2 screws mounting the back side of the body B.
5After pull up the back side of the body B, slide the body B frontward to
remove. (Front portion shall be holded by pawls)
*Incase to remove the body B, Be careful at screw portion of the filling
solenoid.
*Incase to mount the body B, After set the sub tank to the body B.
10