Pandigital PANSCN10 User manual

PORTABLEWANDSCANNER
WITHFEEDERDOCK

UserGuide
PANSCN10

2
UG-E_PANSCN10_v1.0_03-12

3
TableofContents
Read This First.....................................................................................................................................5
Important Safety Precautions...........................................................................................................5
What’s in the Box.................................................................................................................................6
microSD Card Folder Structure..........................................................................................................6
Introduction..........................................................................................................................................7
microSDTM (SDHC) Cards ....................................................................................................................7
Battery Performance............................................................................................................................7
Scanner Overview................................................................................................................................8
Power and Scan Indicator Light .......................................................................................................10
Getting Started...................................................................................................................................10
Considerations for all Scanning.......................................................................................................11
Suitable and Unsuitable Original Types .........................................................................................12
Scanned Image Size ......................................................................................................................12
Access your Scanned Images on SD Card....................................................................................12
Scanned Image File Naming Convention.......................................................................................12
Sheet-fed Scanning with Feeder Dock.............................................................................................13
Wand Scanning (hand-held)..............................................................................................................14
Preview Scanned Images on LCD Screen.......................................................................................15
Set Preview Mode ..........................................................................................................................15
View Scanned JPG Images............................................................................................................16
Delete JPG Images ........................................................................................................................16
Menu - Settings ..................................................................................................................................16
Resolution.......................................................................................................................................16
Color Mode.....................................................................................................................................17
Save Format...................................................................................................................................17
LCD Off...........................................................................................................................................17
Power Saving .................................................................................................................................18
Orientation (best used for PDF scans)...........................................................................................18
Anti-mirror (wand scans only).........................................................................................................19
Card Format ...................................................................................................................................19
Auto-crop (sheet-fed scans only)....................................................................................................20
Language........................................................................................................................................21
Date & Time....................................................................................................................................21
Calibration (as needed only)...........................................................................................................22
Factory Default...............................................................................................................................22
About..............................................................................................................................................22
Use of Protective Sleeves (optional)................................................................................................22
Connect Scanner to a Computer......................................................................................................23
Computer System Requirements ...................................................................................................23
Connect with Windows Vista or Windows 7 ...................................................................................23
Connect with Windows XP .............................................................................................................24

4
Connect with Macintosh Computer.................................................................................................25
Presto! PageManager ........................................................................................................................25
Features .........................................................................................................................................25
System Requirements....................................................................................................................26
Software Installation.......................................................................................................................26
WINDOWS Operating Instructions.................................................................................................27
Launch the Software .................................................................................................................27
View your Scanned Images.......................................................................................................28
Use the Annotation function......................................................................................................28
Image Annotation Toolbar.........................................................................................................29
Text Annotation Toolbar............................................................................................................29
Use Presto! Wrapper.................................................................................................................29
Use the Optical Character Recognition (OCR) Function...........................................................30
Convert images to text (OCR)...................................................................................................30
Set Preferences.........................................................................................................................30
Back up/Restore Files...............................................................................................................31
Restore Files.............................................................................................................................31
Printing from a PC.....................................................................................................................31
Uninstall PageManager.............................................................................................................31
MAC Operating Instructions ...........................................................................................................31
Launch the Software .................................................................................................................31
View your Scanned Images.......................................................................................................32
Edit and Annotate Image...........................................................................................................33
PDF Annotation Toolbar............................................................................................................33
Use the Optical Character Recognition (OCR) Function...........................................................33
Convert images to text (OCR)...................................................................................................33
Set Preferences.........................................................................................................................33
Back up/Restore Files...............................................................................................................33
Restore Files.............................................................................................................................34
Printing from a MAC..................................................................................................................34
Uninstall PageManager.............................................................................................................34
Clean the Scanner and Feeder Dock................................................................................................34
Calibrate the Scanner (Wand Scan mode).......................................................................................35
Error Messages..................................................................................................................................36
Frequently Asked Questions ............................................................................................................36
Technical Specifications ...................................................................................................................39
Store the Scanner ..............................................................................................................................40
Limited Warranty................................................................................................................................40
FCC Statement ...................................................................................................................................42
NewSoft’s End User License Agreement.........................................................................................42

5
ReadThisFirst
Please read the following important safety instructions carefully before using the scanner. Failure
to observe these instructions may result in personal injuries or damages to the scanner.
ImportantSafetyPrecautions
Always follow these basic safety precautions when using your scanner. This reduces the risk
of fire, electric shock, and injury.
Do not place this device under direct sunlight or near heat sources, such as in a
closed car under sunlight or near a stove. The outer casing of this device may
become deformed and the sophisticated sensors inside may become damaged
due to excessive heat.
Do not use this device near water, in the rain or allow any liquid to get inside
this product. Water and moisture may cause short-circuit to the electronic
components and lead to malfunctions.
Do not use this device in dusty environments. Dust grains may cover this device
and scratch the original. Do not scan originals that are contaminated by dusts or
other particles.
Do not use this device near strong electromagnetic sources, such as a
microwave oven or television. The electromagnetic interference may cause this
device to malfunction.
Do not attempt to disassemble or modify this device. There are no user
serviceable parts inside this scanner, and unauthorized modifications void your
warranty.
Do not drop or apply shock/vibration to this device. Strong impacts may
damage the components inside.
Do not insert objects other than compatible memory cards into the memory card
slots of this scanner. The metal contacts inside the slots can easily become
damaged by foreign objects.
Do not use an unknown power adapter other than the one supplied with this
scanner. Connecting this scanner to an unknown power adapter is very
dangerous and may lead to fire or explosion.
Some adapter models may include switchable prongs. When necessary to use
alternate prongs, use only the prongs included with the scanner.
Do not cut, bend, modify, place heavy objects, or step on the cable of the power
adapter. Otherwise the external insulation may be damaged and result in short-
circuit or fire.
The power socket and USB port on this scanner are designed solely for
connecting to the supplied power adapter and optional USB cable. Do not insert
any other objects into these sockets.
If there are strange odors or heat emitting from this device or any signs of
malfunction, disconnect this scanner from the power immediately and contact
your dealer for inspection or service.

6
What’sintheBox
Check the package for the following items. If there are any items missing or damaged, please
contact your place of purchase immediately.
Wand Scanner
Feeder Dock
AC Power Adapter
Rechargeable Batterypack
USB Cable
microSD
TM
Card with Adapter
Cleaning Cloth
Presto! PageManager Software
Quick Start Guide
User Guide
microSDCardFolderStructure

PD_SCAN
DCIM

100PHOTO(for storing scanned photo .jpg files)

200DOC(for storing scanned document .pdf files)
Pandigital

Documentation
QSG (Scanner Quick Start Guide)
UG (Scanner User Guide)

Software
PM#forMacs (Presto! PageManager)

PageManager program folders

PM#forWindows(Presto! PageManager)

PageManager program folders

7
Introduction
Together at last – now you can have the scan-anything anywhere advantages of a battery-
powered wand scanner and the superior ease and quality of a sheet-fed scanner all in one
fashionable solution.
This portable wand scanner quickly and easily makes digital copies of documents, receipts, books,
photos, recipes and more…anytime, anywhere!
Featuring a built-in color LCD preview screen to confirm you’ve captured what you intended, as
well as Pandigital’s ScanRiteTM roller tracking technology to guide your hand-held scans perfectly
to produce straight high-resolution digital copies.
microSDTM(SDHC)Cards
For simplicity purposes in this document, references to the “microSDTM (SDHC) card” may
simply be listed as “SD card”.
The scanner supports up to 32GB microSDTM (SDHC) cards.
The number of images that can be stored on an SD card varies by original size and various
settings available. The table below shows the estimated average number of images that can be
stored on a 2GB SD card:
2GB
SD card
(# of scans
stored)
4x6” original (3.5MP) 5x7” original (5.0MP) 8x10/A4 original (8+MP)
300dpi
color/BW 900dpi color/BW 300dpi color/BW 900dpi color/BW 300dpi color/BW 900dpi color/BW
JPEG 5,500 1,100 3,500 900 1,100 300
PDF 5,500 1,100 3,500 900 1,100 300
BatteryPerformance
The scanner includes a Lithium Ion rechargeable NP-45 Batterypack.
The battery is only needed for hand-held wand scanning. If the “Low Battery” message appears,
your scanned images may be lower quality and the scanner may malfunction. Recharge the
battery as soon as possible.
When the scanner is off and engaged in the feeder dock, the feeder dock charges the battery.
When the scanner is off, you can charge the battery via USB cable connected to your
computer (powered on) or to a USB power adapter. The charging time is longer than when
charging with the feeder dock.
The battery performance varies by size of original being scanned and various available settings.
Battery
performance
(# of photo scans)
4x6” original (3.5MP) 5x7” original (5.0MP) 8x10/A4 original
(8+MP)
300dpi
color/BW 900dpi color/BW 300dpi color/BW 900dpi color/BW 300dpi color/BW 900dpi color/BW
NP-45
(3.7V
700mAh)
JPEG 180 165 175 150 135 100
PDF 180 165 175 150 135 100
An unlimited number of sheet-fed scans can be performed when using the feeder dock.

8
ScannerOverview
Scannertop
No.NameFunction/Description


Powerandscan
indicatorlight
IndicatestheoperatingstatusofthescannerandSDcard.(Referto
“PowerandScanIndicatorLight”onpage10.)


LCDdisplayDisplaysalloperationalmenusandoptions.


UparrowEntersMenuscreenfromScanReadyscreen.
Usedtonavigate“backward”throughimagesandmenuoptions.


PowerButton
Presstoturn onthescanner.
UsedtoacceptoptionschoicesinSettingsandPreviewoptions.
Pressandholdfor3secondstoturnoffthescanner.


BatteryBayCoverSlidetoremovecoverforbatteryaccess. LithiumIon Batterypack
included.


MiniUSBportConnectscannertoyourcomputerviaUSBcable(included)tocopy
scannedimagesfromtheSDcardtoyourcomputer.


microSDcardslotInsertmicroSDTMcardforstoringyourscannedimages.


DownarrowEntersDisplaymodefromScanReadyscreen.
Usedtonavigate“forward”throughimagesandmenuoptions.
BackarrowReturnstopreviousscreensorexitsfromDisplay modeorSettings
menu.

Scannerbottom
No.NameFunction/Description


FeedSensorRollers
Hand‐heldWandscans:therollersarepartofPandigital’s
ScanRiteTMrollertrackingtechnologyforguidingyourscans.
Sheet‐fedwithFeederDock:therollersworkwiththefeederdock
feedsensorrollerstofeedoriginalsthroughthefeedslot.


ContactImageSensor
(CIS)
Thesensorthatscansyouroriginals,whetherusingscanneraswand
scannerorwiththefeederdock.
 




















9
FeederDock
No.NameFunction/Description


ScannerlatchSecuresthescannerinthefeederdock.Pressdownonlatchtoinsert
andreleasescanner.


FeedSensorRollersFeedsoriginalsthroughdevicewhilescanning. Therollersaresensors
andshouldonlyberolledinonedirection.


ScannerconnectorPressscannerontoconnectortoengagescannerwithfeederdock.


OrientationguideShowscorrectalignmentandorientation forfeedingoriginal (printed
sideup).


FeedSlot
Insertoriginal intothefeedslottobeginscanning.
A
lways align
originalprintedsideupstraightagainstleftedgeofthefeeddockand
firmlycontactthesheet‐fedrollerforbetterauto‐cropimaging.


PhotoedgeguidesShowsedgepositionsforfeeding standard 3.5”x5”or4”x6”photosin
portraitorientation.


PhotoedgeguideShowsedgepositionforfeeding4”x6”photosinlandscape
orientation.
A4documentguideShowsedgepositionforfeedingA4sizedocuments.


GuideSlideSlidetheguideuptotherightedgeoftheoriginalbeforeinserting
originalintothefeedslottoensureproperalignmentwhenscanning.
ScannerengagedinFeederDock



Back of feed slot (original output)
Front of feed slot (original input)
A
lways align originals against left edge of slot
DC jack
5V, 1.0A

















10
PowerandScanIndicatorLight
The indicator light patterns and the functions they indicate are as follows:
Off = scanner is off or scanner is on and ready for use
Orange briefly = powering on (wait until the initialization process completes before using
the scanner)
Green steadily on = scanning in progress in 300dpi mode or battery is charging (stays on
until fully charged). In Power Off mode, green LED means the battery is charging.
Orange steadily on = scanning in progress in 900dpi mode
Green or Orange flashing = processing scanned image
Red flashing = no SD card (insert SD card), SD card full, card error, no scan performed
after initiating wand scan mode, or low battery (replace battery).
Green flashes = when scanner is inserted into the feeder dock, 2 green flashes indicate
the switch from battery power to feeder dock power.
GettingStarted
1. Remove the scanner from the feeder dock:
a) Press the latch.
b) Lift the end of the scanner up to clear the latch.
c) Pull the scanner out of the feeder dock to
disengage from the connector.
2. Remove the foam pad from end of scanner and taped cushion inside feeder dock.
3. Insert the Lithium Ion NP-45 rechargeable batterypack:
a) Remove the cover.
b) Insert batterypack.
c) Replace the cover.
4. To charge the battery, insert scanner in the feeder
dock and the power adapter plug into the wall, and
power connector on the end of the feeder dock.
Charge for at least 2 hours (until green LED
goes off) before using the scanner.
5. Insert a SD card.
a
bc
(a)(c) (b)

11
6. Press to turn scanner on.
It is recommended that you read the next section, “Considerations for all Scanning”, before
attempting your first scan.
The battery is not required to operate the scanner when it is engaged in the feeder dock.
TurningtheScannerOff
To turn the scanner off, press and hold for three seconds.
Now you can safely remove the SD card from the scanner.
The scanner has a power-saving feature which automatically turns the scanner off
when it’s left idle for a specified number of seconds (if not connected to a computer). To
set the Power Saving time, see the “Set the Power Saving Time” section on page 18.
ConsiderationsforallScanning
Always insert a SD card before scanning.
Do not remove the SD card or disconnect the power supply while the indicators are blinking.
Keep the original flat and level when feeding to prevent possible jamming.
Keep originals free from finger prints, oil, dirt, and dust for optimum scanned image quality.
The feeder dock’s sensor is triggered when you begin to insert an original aligned against the
left edge of the feed slot, and then the original begins to automatically feed, hesitates and then
completes the scan.
To prevent poor cropping effect, align original straight against left edge of the feeder slot, align
the Guide Slide against the right edge of the original, and ensure there is adequate space
behind the feeder dock for the original to complete the scan feed.
Scanning the same original in different orientations may produce scanned images that look
slightly different in color tones and brightness. This is not a malfunction.
If the SD card is full, the indicator light blinks red and LCD displays “Card Full”. Use another
card or delete some files on it if necessary.
The scanner only accepts SD cards in FAT16 or FAT32 file system. NTFS and other file
systems are not supported.
This scanner supports output images in JPG and PDF formats. (The date & time attributes will
be a pre-assigned fixed value, unless you set the Date & Time option before scanning. See the
Date & Time section on page 21.)
The feeder dock requires 5V 1.0A power adapter to operate and to charge the rechargeable
battery (when the scanner is off).
The battery is not required to operate the scanner when it is engaged in the feeder dock.
The wand scan mode requires you to press to begin scanning an original, and then press
again to stop the scan.
Only the wand scan mode supports the “anti-mirror” feature.
In wand scan mode, if the “Low Battery” message appears on the LCD screen, your scanned
images may be lower quality and the scanner may malfunction. Recharge the battery as soon
as possible.

12
SuitableandUnsuitableOriginalTypes
SuitableforWandScanning
The scanner used as a wand scanner (without the feeder dock) is designed to obtain
the best scanning results with photo and document originals up to 8.5”x14” size.
SuitableforFeederDock
The scanner used with the feeder dock is designed to obtain the best scanning results
with the following types of originals:
Photos and documents (3”x5”, 4”x6”, 5”x7”, 8”x14”)
Business cards (standard 3.5”x2” (8.9x5cm) or larger)
UnsuitableforFeederDock
Do not use the following types of originals for scanning in the feeder dock, otherwise
the feeder dock may malfunction or cause the original to jam in the slot.
Originals thicker than 1.0mm
Originals with either side shorter than 55mm
Originals with lots of black or dark colors
Originals with dark colors surrounding the edges
Printed media (newspapers, magazines, etc.)
Soft and thin materials (thin paper, cloth, etc.)
Originals that exceed the maximum acceptable size, 8.5”x14”.
ScannedImageSize
ATTENTION: Due to the nature of a handheld wand scanner, you may want to manually
crop your image with a graphic editing program. This added step allows you to restore the
saved image to its original size.
AccessyourScannedImagesonSDCard
UsingPresto!PageManager
You can use the included Presto! PageManager software to view, edit and print your
scanned images (see Presto! PageManager on page 25).
UsingWindowsExplorerorMacFinder
If desired, you can use Windows Explorer or Mac Finder to locate and open your
scanned images, and then use a graphic program of your choice to view, edit and print.
Remove the SD card from the scanner and insert it into a card reader attached to your
computer.
OR
With the SD card inserted in the scanner, connect the scanner to your computer via the
USB cable. Your computer recognizes the scanner as a Removable Disk. If you have
the Pandigital SD card inserted, the volume title is PD_SCAN.
ScannedImageFileNamingConvention
After your first scans, folders titled DCIM\100PHOTO (JPG files) and DCIM\200DOC (PDF
files) are added to the SD card file structure, and the scanned images are saved in the
applicable folder.
Each scanned image is given a file name with the prefix PDI_ followed by a 4- digit
sequential number in the order the images are stored. For example, PDI_0001.JPG,
PDI_0002.JPGorPDI_0001.PDF, PDI_0002.PDF, etc.

13
If the file name reaches PDI_9999.JPGor PDI_9999.PDF in the initial folder, a new folder
titled 101PHOTO or 201DOC is automatically created to store subsequent new files, and so
on.
You can view or edit the .JPG files on the SD card by using the included Presto!
PageManager software, or by using your own graphic editing software. You can also use
the Presto! PageManager software to build a book or multiple-page PDF files.
Sheet‐fedScanningwithFeederDock
Always place the feeder dock on a flat surface for scanning.
When the scanner is engaged in the feeder dock, no battery is required to operate.
When the scanner is off and engaged in the feeder dock, the feeder dock charges the battery.
Scanning the same original in different orientations may produce scanned images that look
slightly different in color tones and brightness. This is not a malfunction.
CAUTION: Insert only one original at a time, and insert the next original only when the
previous one is done, otherwise the feeder dock may malfunction.
CAUTION: Do not scan glossy photos in humid environments (humidity higher than 70% RH);
the surface of the photo becomes sticky and may cause the feeder dock to jam.
1. Insert a SD card.
2. Insert the scanner into the feeder dock:
a) Press the latch.
b) Place the right end of the scanner into the
feeder dock and press onto the connector.
c) Press scanner down to snap under latch.
3. Insert the power adapter plug into the wall and
power connector on the end of the feeder dock.
4. Press to turn scanner on.
5. If scanning a document rather than a photo, if desired, change the file format setting to
PDF (see the “Set the Scanned Image File Format” section on page 17).
6. With the side to be scanned facing upward, place the left edge of the original straight
against the left edge of the feed slot, and then slide the guide lever against the right side
of the original.
c
ab

14
7. Gently insert the original into the feed slot; release it as soon as it begins to feed.
After the feed begins, the scanner pauses briefly and then completes the scan.
By default, the Preview mode is on allowing you to preview the scanned image for
2 seconds immediately after scanning. Two options appear on the screen with the
image allowing you to press OK to save (default) or to Delete the image
immediately (delete confirmation displays during deletion). (See page 16 to set the
Preview mode.)
PDF scans cannot be previewed; they are always saved immediately when scan is
completed.
8. Wait until the indicator light stops blinking before inserting and scanning the next original.
WandScanning(hand‐held)
Using the scanner as a wand scanner without the feeder dock allows you to scan a larger variety
of documents, especially those that may not fit in the feeder dock (i.e., pages of a book). It also
allows you to scan vertically or horizontally across the original, which may help you scan book
pages easier.
Our ScanRiteTM roller tracking technology makes it easy to keep the scanner steady to capture
a straight high-quality scan.
For best scanning results, always place your original on a clean flat surface.
The battery is required to operate the scanner without the feeder dock.
If you want to scan a document vertically by sliding the scanner right-to-left (i.e., scanning book
pages), you can change the Orientation setting to Portrait so your saved images will be in the
correct orientation rather than rotated 90oleft (see the “Orientation” section on page 18.)
Scanning the same original in different orientations may produce scanned images that look
slightly different in color tones and brightness. This is not a malfunction.
1. Press to turn scanner OFF.
2. Remove the scanner from the feeder dock:
a) Press the latch.
b) Lift the end of the scanner up to clear
the latch.
c) Pull the scanner out of the feeder dock to
disengage from the connector.
a
bc

15
3. Insert a SD card.
4. Press to turn scanner ON.
5. Press again to initiate the scan mode.
6. With your original on a clean flat surface,
slowly slide the scanner across your original.
Moving the wand scanner over the original too fast causes an error and the scanner
may stop scanning. If the scan does complete, you may notice an abnormal image.
7. Press to stop the scan.
By default, the Preview mode is on allowing you to preview the JPG scanned image
for 2 seconds immediately after scanning. Two options appear on the screen with the
image allowing you to press OK to save (default) to Delete the image
immediately (delete confirmation displays during deletion). (See page 16 to change
the Preview mode.)
PDF scans cannot be previewed; they are always saved immediately when scan is
completed.
8. Wait until the indicator light stops blinking before scanning another original.
PreviewScannedImagesonLCDScreen
You can quickly and easily preview your JPG scanned images on the LCD screen immediately
after a scan, or at any other time you can view all images individually or as a slideshow.
PDF scans cannot be previewed; they are always saved immediately when scan is completed.
SetPreviewMode
By default, the Preview mode is On, allowing you to preview the JPG scanned image for 2
seconds immediately after scanning. Two options appear on the screen with the image
allowing you to press OK to save (default) or to Delete the image immediately
(delete confirmation displays during deletion).
When Preview mode is off, the JPG scanned image is saved immediately without displaying
a preview.

16
Scans performed with Preview mode off use less battery power, so you can expect more
scans with Preview mode off.
ChangethePreviewmode:
1. With the screen displayed, press to enter Menu mode.
2. Press to focus on Preview, and then press to select it.
3. Press to focus on Off, and then press to select it.
4. Press to exit.
ViewScannedJPGImages
If there are no JPEG images on the SD card, preview is disabled.
1. With the screen displayed, press to enter Display mode.
2. The slideshow automatically begins in 4 seconds.
The slideshow continually displays the images in the alphanumeric order they are stored
on the SD card.
3. Press to exit the Display mode and return to the Scan Ready screen.
You can press to display previous or next images, and then the slideshow
resumes after 4 seconds.
To pause the slideshow, press ; to restart slideshow press again.
DeleteJPGImages
1. With the screen displayed, press to enter Display mode.
2. Press to display previous or next images.
3. With an image displayed that you want to delete, press .
4. To delete the image, press and then press to confirm deletion.
5. To delete additional images, repeat steps 2-4.
6. Press to return to the Scan Ready screen.

Menu‐Settings
Resolution
The scan resolution is measured in dpi (dots per inch). The higher the dpi, the more details
on the original are captured by the scanner and produce a higher quality scanned image.
However, a higher dpi also results in a larger image size and occupies more space on the
memory card.
The scanner offers two resolution modes, 300dpi(default, normal) or 900dpi (highest
resolution).

17
To change the scanning resolution:
1. With the screen displayed, press to enter Menu mode.
2. Press to select Settings.
3. Press to select Resolution.
4. Press to focus on the desired scanresolution, and then press to select it.
5. Press to exit.
ColorMode
The scanner offers two color modes for your scanned image, Color (default, recommended
for photos) or BlackandWhite (recommended for text documents).
To change the scanning color mode:
1. With the screen displayed, press to enter Menu mode.
2. Press to select Settings.
3. Press to scroll to ColorMode and then press to select it.
4. Press to focus on the desired mode, and then press to select it.
5. Press to exit.
SaveFormat
The scanner offers two formats for your scanned image output files, JPEG (default,
recommended for photos) or PDF (recommended for text documents and books).
To change the scanned file format:
1. With the screen displayed, press to enter Menu mode.
2. Press to select Settings.
3. Press to scroll to SaveFormat, and then press to select it.
4. Press to focus on the desired fileformat, and then press to select it.
5. Press to exit.
LCDOff
To prevent screen burn-in, the LCD screen automatically shuts off when left idle for a
specified time (45 seconds [default], 90 seconds or 2 minutes).
After the LCD shuts off (and scanner is still on), simply press any button to turn the LCD
back on.
To change the time setting:
1. With the screen displayed, press to enter Menu mode.
2. Press to select Settings.
3. Press to scroll to LCDoff, and then press to select it.

18
4. Press to focus on the desired setting, and then press to select it.
5. Press to exit.
PowerSaving
To conserve power, the scanner automatically shuts off when left idle for a specified time (90
seconds, 3 minutes [default], or 5 minutes).
To change the time setting:
1. With the screen displayed, press to enter Menu mode.
2. Press to select Settings.
3. Press to scroll to PowerSaving, and then press to select it.
4. Press to focus on the desired setting, and then press to select it.
5. Press to exit.
Orientation(bestusedforPDFscans)
The default scan orientation is Landscape, scanning down top-to-bottom of an original. This
orientation works best for the majority of your scanning (JPG or PDF).
or
You can also hold the scanner vertically and scan a
document from right-to-left (i.e., scanning book pages).
However, if you leave the orientation set as Landscape,
the saved image will be rotated 90oleft.
In Portrait mode, the images are automatically rotated 90oright before being saved,
ensuring the vertically scanned image is saved in the correct viewing orientation, thus
eliminating the need to manually rotate the saved images later.
Changing the orientation to Portrait mode is best used for PDF vertical right-to-left scans.
If you need to manually rotate saved images, you can use the included Presto!
PageManager software or your own graphic software.
Scanning the same original in different orientations may produce scanned images that
look slightly different in color tones and brightness. This is not a malfunction.

19
To change the orientation setting:
1. With the screen displayed, press to enter Menu mode.
2. Press to select Settings.
3. Press to scroll to Orientation, and then press to select it.
4. Press to focus on the desired orientation, and then press to select it.
5. Press to exit.
Anti‐mirror(wandscansonly)
This feature is only applicable when using as hand-held wand scanner.
By default, if you wand-scan an original from bottom-to-top, the image is actually captured
upside-down and backwards, and then the Anti-mirror feature automatically flips and
rotates the image before it is saved.
If desired, you can turn the Anti-mirror feature off, resulting in your scanned images saved
upside-down and backwards.
To turn Anti-Mirror off:
1. With the screen displayed, press to enter Menu mode.
2. Press to select Settings.
3. Press to scroll to Anti‐mirror, and then press to select it.
4. Press to focus on Off, and then press to select it.
5. Press to exit.
CardFormat
WARNING: If you reformat your memory card, all existing files on the card are deleted.
To format your SD card:
1. With the screen displayed, press to enter Menu mode.
2. Press to select Settings.
3. Press to scroll to CardFormat, and then press to select it.
4. Press to select Yes.
5. To confirm, press .
6. After a successful format, the Settings screen is displayed.
7. Press to exit.

20
Auto‐crop(sheet‐fedscansonly)
When using the feeder dock, the scanner has a built-in cropping function that detects and
crops dark edges of an original and dark background around an original during the scan
process (see following example).
Original
Scanned images:
Auto-crop on Auto-crop off
To prevent poor cropping effect, align original straight against left edge of the feeder slot
and ensure there is adequate space behind the feeder dock for the originals to complete
the scan feed.
Depending on the shape and size of your original, you may want to perform additional
manual cropping on the scanned image to achieve your desired final image. You can use
the Presto! PageManager software (included) or use your own graphic editing software.
If the original is fed slightly crooked, the original is only cropped a maximum amount per
following illustration:
OriginalCroppedimage
3mm
1.5mm
0.5mm
3mm