Panduit Atlona AT-UHD-SW-510W User manual

Atlona Manuals
Switchers
AT-UHD-SW-510W
Solution Setup and Conguration Guide
Five-Input Universal Matrix Switcher
with Wireless Presentation Link
4K/UHD

AT-UHD-SW-510W 2
Version Release Date Notes
1 Jul 2019 Initial release
Version Information

AT-UHD-SW-510W 3
Introduction 4
Solution Setup and Conguration Guide 5
Input Auto Switching 5
Display Control 7
CEC Control 7
RS-232 Control 11
Conguring IP Control 17
Scheduling Display Operation Times 19
Trigger Port 20
Wiring 20
Conguration using the Web GUI 20
Relay Port 22
Wiring 22
Operation 22
Conguration using the Web GUI 23
Table of Contents

AT-UHD-SW-510W 4
Welcome to the AT-UHD-SW-510W Solution Setup and Conguration Guide. This document covers the following
topics:
• Input Auto Switching
This section explains how to congure the AT-UHD-SW-510W to automatically switch inputs, when sources are
connected or disconnected.
• Display Control
The AT-UHD-SW-510W provides control of display (sink) devices through CEC, RS-232, or IP protocols.
Step-by-step instructions are provided on how to setup each protocol and how to enter commands.
In addition, the display can be automatically powered-on or powered-o based on the current time and date.
The “Scheduling Display Times” section will cover this procedure.
• Trigger Port and Relay Port
Each of these sections explain how to connect devices such as occupancy sensors, screens, curtains, and how
to congure the AT-UHD-SW-510W to work with these devices.
Introduction

AT-UHD-SW-510W 5
The AT-UHD-SW-510W provides auto-switching capability, which will automatically switch the input to the most
recently-connected or powered source, if a so another source is powered-down or disconnected. For example, if the
connection sequence for three separate sources is: DP IN 2 > HDMI IN 4 > HDMI IN 3, and the source connected to
HDMI IN 4 is disconnected (or powered-down), then the AT-UHD-SW-510W will automatically switch to HDMI IN 3,
since this was the last source to be connected.
Auto-switching is enabled (On), by default, and can be enabled or disabled through the web GUI.
Input Auto Switching
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
LAN DC 24V
HDBaseT OUT
HDMI OUTHDMI IN
DP IN
USB-C IN
2 3 4
1
RELAY RS-232
TRIGGER I/O
MIRACASTWiFi AUX
AUDIO
OUT
L R
IN
USB
+
C1 COM C2 RX
PTX
+
+
USB
USB
USB
1. Launch a web browser.
2. In the address bar, type the IP address of the AT-UHD-SW-510W.
3. Enter the login credentials and click the Login button. The default credentials are listed below:
Username: admin
Password: Atlona
4. The Info page will be displayed, as shown on the next page.
Solution Setup and Conguration Guide

AT-UHD-SW-510W 6
5. Click Display in the menu on the left side of the window.
6. Locate the AutoSwitch check box, under the Control window group.
Solution Setup and Conguration Guide
7. Click this check box to enable auto-switching. When auto-switch is enabled, a check mark will appear in this
box. To disable auto-switching, click the AutoSwitch check box again.

AT-UHD-SW-510W 7
Display Control
The following section cover display control using the following methods:
• CEC
• RS-232
• IP
CEC Control
CEC Control over HDMI
HDMI
AT-UHD-SW-510W
Display
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
Solution Setup and Conguration Guide
AT-UHD-SW-510W
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
LAN DC 24V
HDBaseT OUT
HDMI OUTHDMI IN
DP IN
USB-C IN
2 3 4
1
RELAY RS-232
TRIGGER I/O
MIRACASTWiFi AUX
AUDIO
OUT
L R
IN
USB
+
C1 COM C2 RX
PTX
+
+
USB
USB
USB
to display
Consumer Electronics Control (CEC) is the simplest method when working with a consumer display. Note that the
display must have CEC enabled to receive CEC messages. CEC can be transmitted over HDMI and/or HDBaseT.
Note that if both connection methods are used, simultaneously, the same CEC messages will be transmitted over
both HDMI OUT and HDBaseT OUT ports.
a. Connect an HDMI cable from the HDMI OUT port on the AT-UHD-SW-510W to an HDMI input on the display
device.

AT-UHD-SW-510W 8
Solution Setup and Conguration Guide
CEC Control over HDBaseT
HDBaseT
HDMI
AT-UHD-SW-510W
AT-UHD-100CE-RX-PSE
Display
DC48V RS-232 HDBaseTIN HDMI OUT
RXTX
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
AT-UHD-SW-510W
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
LAN DC 24V
HDBaseT OUT
HDMI OUTHDMI IN
DP IN
USB-C IN
2 3 4
1
RELAY RS-232
TRIGGER I/O
MIRACASTWiFi AUX
AUDIO
OUT
L R
IN
USB
+
C1 COM C2 RX
PTX
+
+
USB
USB
USB
to compatible receiver device
1. Enable CEC on the display device. Refer to the documentation for the display device. It should be noted that
dierent manufacturers will identify CEC with their own brand name. Refer to the table below.
Manufacturer CEC Designation
Hitachi HDMI-CEC
LG SIMPLINK
Philips EasyLink
Samsung AnyNet+
Sony BRAVIA Sync
Toshiba CE Link / REGZA Link
Visio HDMI-CEC
a. Connect a category cable (CAT-5e or better) from the HDBaseT OUT port on the AT-UHD-SW-510W to a
compatible receiver. The example below uses an AT-UHD-100CE-RX-PSE.
b. Connect an HDMI cable from the HDMI OUT port on the receiver to the HDMI input on the display device.

AT-UHD-SW-510W 9
Solution Setup and Conguration Guide
2. Launch a web browser.
3. In the address bar, type the IP address of the AT-UHD-SW-510W.
NOTE: If using AMS and the AT-UHD-SW-510W is running 2.4.0 or greater, click on the device within
AMS to access the web interface.
4. The Login page will be displayed. Enter the required credentials. The default credentials are shown below:
Username: admin
Password: Atlona
5. Click the Submit button or press the ENTER key on the keyboard.
6. Click Display in the menu on the left side of the window.
7. Click the Control Type drop-down list and select CEC.
8. Under the CEC section, next to HDMI, test the power-on and power-o commands by clicking the ON and OFF
buttons, respectively. The display should power-on and power-o when clicking these buttons.

AT-UHD-SW-510W 10
Solution Setup and Conguration Guide
If the display does not respond, check the following:
• Verify that CEC is enabled on the display device.
• Verify the integrity of the HDMI cable. Try connecting a dierent HDMI cable between the AT-UHD-SW-510W
and the display device.
• Try connecting the HDMI cable to a dierent HDMI input on the display device.
Consumer Electronics Control (CEC): Atlona has conrmed proper CEC functionality with several current models of
Samsung, Panasonic, and Sony displays. However, it is not guaranteed that CEC will work with all displays. Many
manufacturers do not support the CEC “o” command, and older displays use proprietary commands. Atlona only
supports displays that use the CEC command structure dened in HDMI 1.2a. It is recommended that dealers re-
quest an evaluation product from Atlona, before designing a system using the CEC protocol. If this is not possible,
then other control methods will need to be considered, in order to control displays using Atlona products.