Panduit ATLONA Omega AT-OME-MS52W User manual

1
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
The Atlona AT-OME-MS52W is a 5x2 matrix switcher with HDMI, USB-C, DisplayPort, and
wireless AV inputs, plus HDMI and HDBaseT outputs. It features wireless presentation capability
and native screen mirroring for iOS®, Android™, Mac®, Chromebook™, and Windows®. Part of
the Omega™ Series of integration products for modern AV communications and collaboration,
the OME-MS52W is HDCP 2.2 compliant and features HDBaseT extension for video up to 4K/60
4:2:0, plus embedded audio, control, Ethernet, and USB* over distances up to 330 feet (100
meters). All inputs and the local HDMI output support 4K HDR and 4K/60 4:4:4 at HDMI data
rates up to 18 Gbps. Additionally, 4K downscaling to 1080p @ 60, 30, or 24 Hz is available for
the HDMI output when connected to an HD sink. The integrated USB extension addresses the
challenge of connecting between USB devices at remote locations, and is ideal for software
video conferencing and touch or interactive displays. The OME-MS52W includes USB 2.0 and
USB-C interfaces for three host PCs, plus two peripheral devices such as a camera, microphone,
speakerphone, or keyboard and mouse.
IMPORTANT: Visit http://www.atlona.com/product/AT-OME-MS52W for the latest
rmware updates and User Manual.
1 x AT-OME-MS52W or AT-OME-MS52W-EU
1 x Captive screw connector, 5-pin
1 x Captive screw connector, 4-pin
2 x Captive screw connector, 3-pin
2 x WiFi antenna modules
1 x USB-C cable, 2 meters
1 x 24 V DC power supply
2 x Mounting plates
4 x Mounting screws
1 x Installation Guide
Package Contents
Omega™ 4K/UHD 5x2 Matrix Switcher for HDMI, USB-C,
DisplayPort, and HDBaseT with USB and Wireless Link
AT-OME-MS52W
AT-OME-MS52W-EU

2
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
1 USB HOST
Connect a USB cable from each of these
ports to host computers.
2 USB HUB
Connect up to two USB devices (e.g.
mouse, keyboard, etc.) to these ports.
These ports provide 2.5 W per USB
device interface.
3 OUT 1 / OUT 2 LED Indicators
Each set of LED indicators displays the
output being used: OUT 1 = HDMI OUT,
OUT 2 = HDBaseT OUT.
4 POWER
Press this button to power-on or power
o the AT-OME-MS52W and/or the
connected displays. Refer to the User
Manual for more information.
5 SHOW IP
Press this button to display the IP address
of the AT-OME-MS52W on the connected
display.
Panel Descriptions
Front
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB USB
USB
USB
USB
4OUTPUT LAN DC 24V
32 INPUT
USBAUDIO
WiFi AUXIN
RS-232
RX TX
RELAY TRIGGER I/O
COMC1 C2 P
OUTL RRESET
IP MODE
MIRACASTTM
1 21
21 3 4 5

3
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB USB
USB
USB
USB
4OUTPUT LAN DC 24V
32 INPUT
USB
AUDIO
WiFi AUXIN
RS-232
RX TX
RELAY TRIGGER I/O
COMC1 C2 P
OUTL RRESET
IP MODE
MIRACASTTM
1 21
1 4 7 10 11 13
32 5 6 8 9 12 14
1 IP MODE
Press and release this button to set the
IP mode of the AT-OME-MS52W. Refer
to IP Conguration (page 11) for more
information.
2 RESET
Press and release this button to reset the
unit to factory-default settings. Refer
to Resetting to Factory-Default Settings
(page 11).
3 INPUT (USB-C)
Connect a USB-C cable from this port to
a USB-C source.
4 AUDIO
Connect a 3.5 mm mini-stereo cable from
an analog audio source to the IN port,
to provide optional embedded analog
audio on the output. Connect a balanced
stereo audio output device to the OUT
port using the included captive screw
block. Refer to Audio (page 4) for
wiring information.
5 INPUT (DisplayPort)
Connect a DisplayPort device to this port.
6 INPUT (HDMI)
Connect an HDMI cable from each of
these ports to a UHD/HD source.
7 USB
Connect the included WiFi antenna
to these ports. The MIRACAST port
is reserved for the Miracast casting
protocol. The AUX port is reserved for
system use.
8 OUTPUT (HDMI)
Connect an HDMI cable from this port
to an HD/UHD display.
9 OUTPUT (HDBaseT)
Connect to a locally powered HDBaseT
receiver such as the AT-OME-EX-RX.
10 RELAY
Connect one of the included 3-pin
captive screw connectors to this port to
control screens, drapes, lights, or other
devices.
11 TRIGGER I/O
Connect voltage-controlled device to this
port. A 4-pin captive screw connector is
required.
12 LAN
Connect an Ethernet cable from this port
to the network.
13 RS-232
Use the included captive screw connector
to connect an RS-232 controller or
automation system.
14 DC 24V
Connect the included power supply to
this power receptacle.
Back

4
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
The AT-OME-MS52W provides an RS-232 port which can be used to control a display connected
to the HDMI output. Atlona recommends controlling the AT-OME-MS52W using IP and reserving
the RS-232 port for local display control.
1. Use wire strippers to remove a portion of the cable jacket.
2. Remove at least 3/16” (5 mm) of insulation from each of the wires.
3. Insert the wires into correct terminal using the included 5-pin captive screw connector.
4. Attach the 5-pin connector block to the RS-232 port on the AT-OME-MS52W.
NOTE: Typical DB9 connectors use pin 2 for TX, pin 3 for RX, and pin 5 for ground.
On some devices functions of pins 2 and 3 are reversed.
RS-232
GND
RX
TX
The AT-OME-MS52W provides the ability to output two-channel balanced analog audio on the
AUDIO OUT port, using the included 5-pin captive screw connector.
Use wire strippers to remove enough insulation to allow each wire to be securely fastened
to each terminal of the captive screw connector block and connect the wires as shown.
Unbalanced audio is not supported.
Audio
Balanced XLR audio
2 1
3
2 1
3
GND GND
-
+
Rear View Rear View
-
+

5
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
Relay
The AT-OME-MS52W provides a RELAY port, allowing the control of screens, curtains, and other
devices. Use a 48 V DC relay with no more than 1 A current draw.
When the AT-OME-MS52W is powered-on or rebooted, C1 and C2 are set to the Normally Open
(NO) state.
C2
COM
C1
Trigger
The TRIGGER I/O port allows voltage-controlled devices, such as an occupancy sensor,
to be connected to the AT-OME-MS52W. Use the included 4-pin captive screw connector to
connect the device. Voltage range is 3 to 30 V DC.
Powered sensor
Passive sensor
Control (Set HIGH)
+12 V DC
Passive sensor
- + P
Common (Set LOW)
Control (Set HIGH)
Powered sensor
30 V (max.)
- + P
GND

6
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
3. Connect a USB-C cable from a source to the USB-C (1) port.
4. Connect a DisplayPort cable from a source to the DP IN (2) port.
5. Connect up to two UHD/HD sources, using HDMI cables, to the HDMI IN (3) and HDMI IN
(4) ports.
6. Connect an HDMI cable from the HDMI OUT port to a UHD/HD display.
7. Connect a category cable (CAT-5e or better), up to 330 feet (100 meters), from the HDBaseT
OUT port to a compatible receiver, such as the AT-OME-EX-RX.
8. Connect an Ethernet cable from the LAN port to the Local Area Network (LAN). Atlona
recommends this step and provides access to the built-in web server, which can be used to
control and manage the AT-OME-MS52W.
Installation
1. Connect up to two USB host computers to the USB HOST ports on the front panel.
2. Connect up to USB devices, such as a speakerphone, to the USB HUB ports on the front
panel.
IMPORTANT: Only use Atlona WiFi USB modules. Other WiFi modules may
not be supported by this product.
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB USB
USB
USB
USB
4OUTPUT LAN DC 24V
32 INPUT
USBAUDIO
WiFi AUXIN
RS-232
RX TX
RELAY TRIGGER I/O
COMC1 C2 P
OUTL RRESET
IP MODE
MIRACASTTM
1 21
9. Connect the included USB wireless antennas to the WiFi and MIRACAST™ ports.
The WiFi port supports Google Cast™ and Apple AirPlay®. The MIRACAST™ only
supports Miracast.
10. OPTIONAL: Connect a 3.5 mm analog audio cable from an analog source to the AUDIO IN
port. This audio source can be used to embed analog audio on any of the input sources.
11. OPTIONAL: Connect the included green 5-pin captive screw connector to the AUDIO OUT
connector. Refer to Audio (page 4) for wiring information.
1 2
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB USB
USB
USB
USB
4OUTPUT LAN DC 24V
32 INPUT
USB
AUDIO
WiFi AUXIN
RS-232
RX TX
RELAY TRIGGER I/O
COMC1 C2 P
OUTL RRESET
IP MODE
MIRACASTTM
1 21
3 4 6
7 8
9
10 11
5

7
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
12. OPTIONAL: Connect the relay leads from the control motors of the projection screen,
blinds, or curtains, to the relay outputs to the RELAY port, using the included 3-pin captive
screw connector. Use a 48 V DC relay with no more than 1 A current draw. Refer to Relay
(page 5) for wiring information.
13. OPTIONAL: Connect a trigger device, such as an occupancy sensor switch, to the
TRIGGER I/O port. A 4-pin captive screw connector is required. Voltages from 3 to 30 V
are supported. Refer to Trigger (page 5) for wiring information.
14. OPTIONAL: Use the included captive screw connector to connect a serial cable from the
RS-232 port on the AT-OME-MS52W, to the RS-232 port on the display. Refer to RS-232
(page 4) for wiring information.
15. Connect the included power supply to the DC 24V connector and connect the power cord
to an available electrical outlet.
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB USB
USB
USB
USB
4OUTPUT LAN DC 24V
32 INPUT
USB
AUDIO
WiFi AUXIN
RS-232
RX TX
RELAY TRIGGER I/O
COMC1 C2 P
OUTL RRESET
IP MODE
MIRACASTTM
1 21
12 13 14
15

8
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
Mounting Instructions
The AT-OME-MS52W can be mounted in dierent ways, based on the number of units that are
being installed. The AT-OME-MS52W can be mounted in a rack or on/under any at surface.
Single-unit rack installation
1. Attach the included small rack ear (sold separately) to one side of the AT-OME-MS52W,
using the included screws.
2. Attach the included longer rack ear (sold separately) to the opposite side of the AT-OME-
MS52W using the included screws.
AT-RON-444
+
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB
USB

9
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
Dual-unit rack installation
1. Turn both units upside-down on a at surface, next to each other, as shown.
2. Position the included mounting plates over the holes on the bottom of the enclosure.
When attaching mounting plates, the countersink bevels on the mounting plate should face
upward.
POWER
SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB
USB
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1
OUT 2
AT-OME-MS52W
USB
USB
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB
USB
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB
USB
AT-RON-444
+
AT-RON-444
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB
USB
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB
USB
3. Turn the attached units over and install the rack ears (sold separately) to one side of each
enclosure using the included screws.
Countersink bevel

10
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
Flat surface
1. Turn the unit upside down on a at surface.
2. Position the included mounting plates over the pre-drilled holes on the bottom of the
enclosure. When attaching mounting plates, the countersink bevels on the mounting plates
should face upward.
3. Mount the unit using the circular holes, on each mounting plate. If using a drywall surface,
a #6 drywall screw is recommended. Mounting screws are not included.
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
AT-RON-444
+
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAYINPUT
AT-UHD-SW-510W
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
Countersink bevel
NOTE: The unit can also be mounted under a at surface, such as a table, by
turning the unit upside down.

11
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
By default, the AT-OME-MS52W is set to DHCP mode, allowing a DHCP server (if present) to
assign the unit an IP address. If a DHCP server is not found within 15 seconds, then the unit will
be placed in Auto IP mode and use a self-assigned IP address within the range of 169.254.xxx.
xxx. If either DHCP or Auto IP mode are not desired, then the unit can be placed into static IP
mode.
IP Conguration
Switching to Static IP mode
Switching to DHCP mode
Resetting to Factory-Default Settings
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB USB
USB
USB
USB
4OUTPUT LAN DC 24V
32 INPUT
USB
AUDIO
WiFi AUXIN
RS-232
RX TX
RELAY TRIGGER I/O
COMC1 C2 P
OUTL RRESET
IP MODE
MIRACASTTM
1 21
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB USB
USB
USB
USB
4OUTPUT LAN DC 24V
32 INPUT
USB
AUDIO
WiFi AUXIN
RS-232
RX TX
RELAY TRIGGER I/O
COMC1 C2 P
OUTL RRESET
IP MODE
MIRACASTTM
1 21
1. Press and hold the RESET button for ve seconds.
2. Release the RESET button once the RESET LED indicator begins to ash. The LED
indicator will ash three times to indicate that the unit has been reset to factory-default
settings.
IP MODE button
RESET button
1. Press and hold the IP MODE button for ve seconds.
2. Release the IP MODE button once the IP MODE LED indicator begins to ash.
3. The IP MODE LED indicator will ash green two times, indicating that the unit is now in
static IP mode. As part of static IP mode, the AT-OME-MS52W will be assigned the IP
address of 192.168.1.254.
1. Press and hold the IP MODE button for ve seconds.
2. Release the IP MODE button once the IP MODE LED indicator begins to ash.
3. The IP MODE LED indicator will ash green four times, indicating that the unit is now in
DHCP mode. This is the factory-default setting.

12
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
3. Press the SHOW IP button on the front panel.
1. Make sure the unit is powered.
2. Connect a display to the HDMI OUT port of the AT-OME-MS52W.
Displaying the Current IP Address
to display
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB USB
USB
USB
USB
4OUTPUT LAN DC 24V
32 INPUT
USB
AUDIO
WiFi AUXIN
RS-232
RX TX
RELAY TRIGGER I/O
COMC1 C2 P
OUTL RRESET
IP MODE
MIRACASTTM
1 21
NOTE: If the HDBaseT OUT port is used as the output, then a compatible
receiver, such as an AT-OME-EX-RX, will need to be connected to the AT-OME-
MS52W, then connect the display to the HDMI output on the AT-OME-EX-RX.
The fastest method is to connect a display to the HDMI OUT port of the AT-
OME-MS52W.
NOTE: The input selection on the front panel can be set to any input. In this
case, only an output is required to display the IP address.
IP: 192.168.1.254
NETMASK: 255.255.255.0
POWER SHOW IP
DP
HDMI 3
HDMI 4
BYOD
USB-C
USB HOST
21
USB HUB
OUT 1 OUT 2
AT-OME-MS52W
USB USB
4
HDMI OUT HDBaseT OUT LAN DC 24V
32
USB-C IN DP IN HDMI IN
USBAUDIO
WiFi AUXIN
RS-232
RX TX
RELAY TRIGGER I/O
COMC1 C2 P
OUTL RRESET
IP MODE
MIRACASTTM
USB
USB
USB
4. The IP address and the subnet mask of the AT-OME-MS52W will be displayed in the lower-
left corner of the display, as shown below.

13
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
Accessing the Web Server
The AT-OME-MS52W includes a built-in web server, which allows easy management and control
of all features. Follow the instructions below to access the web server.
1. Make sure that an Ethernet cable is connected between the LAN port on the AT-OME-
MS52W and the network.
2. Launch a web browser and enter the IP address of the unit. If the default static IP address
is being used, enter 192.168.1.254.
3. The AT-OME-MS52W Login page will be displayed.
4. Enter the following information on the Login page.
Login: admin
Password: Atlona
5. Click the Login button.
6. Refer to User Manual for detailed operation of the web server.

14
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
Troubleshooting
Problem Solution
The source image is not
displayed.
• Check all cable connections between the AT-OME-
MS52W and the source(s) and display.
• Check the input indicators on the front panel to make
sure that the correct input is selected for the output. OUT
1 = HDMI OUT, OUT 2 = HDBaseT OUT.
• Try switching to another input to verify all source
connections.
Auto-switching is not
working.
• Check all cable connections between the AT-OME-
MS52W and source devices. If the cable between the
source and the AT-OME-MS52W is damaged or is not
secure, then this will prevent auto-switching from working
correctly.
• Verify that audio switching is set to ON, under the
Conguration menu in the web server.
The USB-C port is not
charging my USB device.
• Check that the USB cable is not damaged and provides a
secure connection between the AT-OME-MS52W and the
USB device.
• Check the voltage rating of the connected device to
make sure it is compatible. Maximum power and voltage
ratings for the USB-C port are as follows: 60 W @ 20 V,
36 W @ 12 V, and 15 W @ 5 V.
The AT-OME-MS52W is
not controlling the display.
RS-232
• Verify the wiring of the RS-232 captive screw connector.
• Make sure that the proper command syntax is being
used; use an RS-232 terminal emulator to verify the
command.
• Verify that the device ID, control method for the display,
and control settings for the AT-OME-MS52W are correct.
IP
• Make sure that the AT-OME-MS52W is on the same
network as the display.
• Ping the display to verify that it is reachable.
• Verify that proper command syntax is being used.
CEC
• Check CEC settings on the display.
• Verify that proper command syntax is being used.

15
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
Notes

16
Installation Guide
AT-OME-MS52W / AT-OME-MS52W-EU
Version 1
© 2020 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered
trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and
online product images may vary from images shown here.
Toll free US International
atlona.com •877.536.3976 •41.43.508.4321