Panduit Atlona AT-VCC-RS232-KIT User manual

Installation Guide
AT-VCC-RS232-KIT
1
IP to RS-232 Command Converter for Velocity Control
System
AT-VCC-RS232-KIT
The Atlona AT-VCC-RS232-KIT is an accessory for the Atlona Velocity™ Control System that
provides conversion between IP and RS-232 control commands. This Velocity Control Converter
is very compact and can be placed anywhere a device requires control and is not IP-capable.
The VCC-RS232-KIT is remotely powered through Power over Ethernet (PoE), or locally from a
USB power source. The primary unit installs onto any surface via a convenient mounting dock. A
simple “click” locks it into place for a secure, reliable installation. An RS-232 gender changer is
included.
1 x AT-VCC
1 x AT-VCC-RS232
Package Contents
Operating Notes
• The Velocity Command Converter must be on the same network as the Velocity Gateway
(AT-VGW-250) or it will be unable to sync for control.
• The AT-VCC-RS232-KIT is PoE, to power the unit, simply plug it into a PoE compatible
network switch. If the network switch is not PoE capable, a PoE injector (purchased separately)
or USB can be used.
• All devices (AT-VCC, Velocity, AT-VTP, switchers, etc) should be set to static IPs or the
DHCP IP address reserved for each individual device.
IMPORTANT: Velocity Gateway (AT-VGW-250) must be set up before the AT-VCC-RS232-
KIT is fully functional.

Installation Guide
AT-VCC-RS232-KIT
2
1 2 3 4 5
1 Ethernet
Connect an Ethernet cable from this
port to the same network as the Velocity
Gateway .
2 USB
Not used at this time.
3 3.5mm Port
Connect to a VCC RS-232 3.5mm
connector.
4 RS-232 Connector
Connect the RS-232 connector into the
RS-232 port of the controlled device.
5 3.5mm Connector
Connect the 3.5mm connector to the
3.5mm port of the VCC.
Panel Description

Installation Guide
AT-VCC-RS232-KIT
3
IP
The AT-VCC is set to DHCP by default. If the network does not support DHCP, it will
automatically set the AT-VCC to the static IP of 192.168.1.70 after 30 seconds.
VHelp and webGUI
Velocity will nd the VCC when scan network is used, but if the VCC needs to be set up o site
rst, the software VHelp can be used.
1 Connect the RS-232 connector into the 3.5mm port on the unit.
2 Connect the AT-VCC to a network switch (PoE is best if a PoE switch is not available, a
power injector or mini USB to USB cable may be used).
3 Download VHelp from the resource tab of http://atlona.com/AT-VCC-IR-KIT.
4 Unzip the le to the local PC
5 Double-click the VHelp executable to open the program. Vhelp will start discovery as soon
as the program is opened.
6 Double click on the VCC (to determine the correct one, look on the bottom of the VCC for
the MAC address). The PC default browser will open to the AT-VCC webGUI.
7 Select Network Settings to open the IP conguration page.
8 Select the DHCP Enabled header, this will disable DHCP and allows IP settings to be edited.
9 Type in the IP details to
match the network details
of the Gateway. e.g. If the
Velocity gateway is located at
the IP of 192.168.12.15, then
the VCC should be set to an
IP within the 192.168.12.XXX
range that has not already
been used.

Installation Guide
AT-VCC-RS232-KIT
4
10 Press the Save Changes button. If the IP was changed, the browser will redirect to the
general ‘Page Not Found’ page.
11 Open any browser on the network and type in the IP address of Velocity.
12 Select the =button from the top left corner and select Sites.
13 Select the building that corresponds with the room of the VCC.
14 Select the room the VCC is located in. A new screen will take over the window and display
the technology in the room.
15 Select the + button located at the top right corner of the room. A new menu will open.
NOTE: Connecting the VCC to Velocity can only be done once Velocity has been set
up. View the Velocity Manual for instructions.
16 Press the scan network button. All Atlona devices found will appear in the unassigned list.
17 Select the Add button next to the VCC. A new pop up will appear.

Installation Guide
AT-VCC-RS232-KIT
5
18 Select the VCC Serial from the drop down menu.
19 Press the ADD VCC TO ROOM button. A VCC tile will appear in the room.
20 Select edit on the controlled device’s tile.
21 Select RS232 from the Control Type drop down menu.
New elds will appear with baud settings. These options should be auto-lled with the device’s
parameters. If the parameters have changed or are incorrect, they can be updated.

Installation Guide
AT-VCC-RS232-KIT
6
22 Select Velocity Command Converter from the RS232 Connection drop down menu.
23 Press the SAVE button.
Velocity will automatically set the Velocity Command Converter to the correct baud parameters
when the save button is pressed.
• Select Serial from the drop down menu.
• Type the VCC’s IP into a web browser to open the Velocity Command Converter
Conguration.
• Select Velocity Control Cable from the two options.
NOTE: If for some reason the unit isn’t syncing or the settings aren’t being set, they
can be set up manually through the VCC webGUI.

Installation Guide
AT-VCC-RS232-KIT
7
NOTE: The RS-232 parameters should match the controlled device. Verify the
parameters using the source or display’s manual.
• Fill in the controlled device’s RS-232 parameters: Baud Rate, Flow Control, Parity, Data
Bits, and Stop Bits.
• Select Save Conguration. The VCC is now set up and ready to use.

Installation Guide
AT-VCC-RS232-KIT
8
Version 2
© 2019 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered
trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and
online product images may vary from images shown here.
Toll free US International
atlona.com •877.536.3976 •41.43.508.4321