Panoview Panoview Graywolf II User manual

NO.1
Close supervision is necessary when any motorized
screen is used by or near children,do not leave motorized
screen unattended while in use.
Do not operate motorized screen with damaged cord or if
the motorized screen has been dropped or damaged,until it
has been examined by a qualified service technician.
Position the cord so that it will not be tripped over,pulled or in
contact with not surgaces.
Never yank cord to pull plug form outlet.aways grasp plug
bu head and pull to disconnect.
Let appliance cool completely before putting away.Loop
cord loosely around appliance when stoing.
To reduce the risk of electric shock,do not immerse this
motorized screen in water or other liquids.
Basic safety precautions,including the following should
always be followed.
IMPORTANT SAFETY INSTRUCTIONS

N0.2
To reduce the risk of electric shock,do not disassemble this
appliance,only a qualifid service technician may service or
repair motorized screen.Incorrect reassemble can cause
electric shock when the motorized screen is used.
Only use accessory attachment recommended by the
manufacturer.Use of non-manufacturer recommended acces-
sory attachments,may viod the screens warranty and release
Panoview of all liability.
Basic electrical safety precautions should always be observed.
In the event,the above mentioned safety precautions are not
observed.The warranty may be viod and Panoview released of
all liability.
OPERATING INSTRUCTION:

NO.3
Thank you for choosing Panoview screens. All screens
have passed the strict quality inspection before delivery.
Read this manual carefully to ensure proper usage.
Important Attention: the installation of the screen,
the electric wire connection, the setting of the limit
switches must be made by a trained engineer only.
Motorized screen with IR remote control, switch control & 12v trigger port
SWITCH BOX
PLUG
SWITCH JACK
12V TRIGGER
ELECTRIC CONNECTION

N0.4
Unpack screen carefully, be sure screen is in good condition,
and check that all accessories are included inside carton.
Care in mounting and care in correct operation will mean a long
and satisfactory life for your Panoview screen. Locate the screen
where the audience can best see it and where other furnishings in
the room permit.
Check that voltage and frequency marked on screen is in
accordance with local power utility. It is suggested only to use
screen indoor under normal temperature and humidity conditions.
Technical data:
Input Voltage: 110VAC/60HZ
Output Voltage: 3A
Fuse: 1A
IR Remote Control Distance: ≤8m, ±15°Horizontal
12V Trigger Jack: OD3.4xID1.3
12V Trigger Signal: Voltage:7---11VAC or 8---16VDC,
Current: ≥2mA
IR Handset: 1pc
Switch control: 1pc

NO.5
Remove two pulling locks on the bottom slat bar after the case
has been installed.
Install screen brackets onto ceiling or wall with appropriate
hardware.
Anchor screen onto bracket as shown in above figure below.
MOUNT SCREEN TO WALL MOUNT SCREEN TO CEILING

N0.6
ELECTRIC CONNECTION
Internal wiring has been completed at the factory.No addi-
tional wiring is necessary.
Note:all wiring related to the screen,may only
be serviced by a manufacturer approved trained
electrical technician.Tampering with electrical
wiring may void warranty and release Panoview
of liability.

NO.7
OPERATING INSTRUCTION:
OPERATING INSTRUCTION:
Plug in power supply.
For Switch control: Plug in Switch into switch jack. Press
button to Up position, screen goes up. Press button to stop
position, screen stops. Press button to down position,
screen goes down.
For IR Remote: Direct the handset to IR window on
screen housing. Press the Up/Stop/Down button on the
hand set, screen goes Up/Stop/Down accordingly.

N0.8
For 12V trigger: Input 12V trigger signal, screen goes
down. Stop this signal, screen goes up.
Electric lock: Press the Up & Down buttons on the IR
handset together, then all Up & Down buttons on the switch
and IR handset will be locked. To be unlocked press Stop
button on the IR handset again or unplug the power supply
and plug in again.
Keeping the screen rolled in its protective case when not
in use. Always examine both front and back of surface
before re-rolling into case to make certain screen is free of
dust, dirt or other foreign matter.