Paradigm Health & Wellness InfraLife 9720 User manual

Portable infrared Heater
Item #9720
OWNER’S MANUAL

TABLE OF CONTENTS
1
SERVICE -------------------------------------------------------------------------2
IMPORTANT LABELS -------------------------------------------------------- 3
SAFETY PRECAUTIONS --------------------------------------------------- 4
PART DRAWING --------------------------------------------------------------- 5
PART LIST ----------------------------------------------------------------------- 6
OPERATING INSTRUCTIONS --------------------------------------------- 7
MAINTENANCE ---------------------------------------------------------------- 9
WARRANTY -------------------------------------------------------------------- 10
FAX FORM ---------------------------------------------------------------------- 11

IMPORTANT: FOR NORTH AMERICA ONLY
To request product service and order
replacement parts, please call our
customer service department at:
1-866-924-1688
Monday through Friday, 8:00 AM-5:00 PM Pacific Standard Time,
or email us at: [e-mail]
Please visit our website at www.paradigmhw.com.
Please have the following information ready when requesting for service:
Your name
Phone number
Model number
Serial number
Part number
Proof of Purchase
*Before returning this product to the store please contact
customer service at the contact number.
Paradigm Health & Wellness, Inc.
1189 Jellick Ave, City of Industry, CA 91748, USA
SERVICE
2

AVERTISSEMENT POUR REDUIRE LER RISQUES D'INVENDIE
-
1. Appareils de chauffage doit toujours être branché directement dans une prise
murale / réceptable. Ne jamais utiliser une rallonge, ou du robinet d'alimentation
amovible (sortie mulriprise/) 2.Vérifiez votre cordon chauffant et connexions
les connexions défectueuse prise murale ou bouchon lache peut provoquer la prise
ou la fiche de surchauffer. Assurez-vous que la fiche est bien serréedans la orise.
Lors de l'utilisation vérifier fréquemment pour determiner si votre prise de prise ou de la façade est CHAUD! Si c'est le cas, cesser l' utilisation du chauffe –eau et ont
un contrôle Electrician qualifié et ou /remplacer la prise défectueuse (s)
3.Toujours brancher le radiateur lorsqu'il n'est pas utilisé.
4.Ne pas fonctionner le radiateur avec un cordon ou une fiche endommagé ou après
un dysfonctionnement a été échappé ou endommagé de quelque façon. Chauffe
keter ou tourner à un centre de service autorisé pour examen et/ou reparation.
5.Ne pas passer le cordon sous un tapis.Ne pas couvrir le cordon avec des tapis, ni de
tout autre. Ne pas passer sous des meubles ou des appareils.Placez le cirdon des
aires des circulation et où il ne sera pas Trébucher
NE PAS RETIRER LE PRESENT TAG
This WARNING label is stuck on the power cord.
IMPORTANT LABELS
3

When using this heater, basic safety precautions should always be followed
to reduce the risk of fire, electric shock, and injury to persons, including the
following:
1. Read all manual before using this heater.
2. WARNING: Risk of Fire-Keep combustible material away from front of heater.
3. WARNING: Risk of Fire-Keep combustible material such as furniture, papers,
clothes, and curtains at least 3 feet (0.9M) from the front of the heater and
away from the sides and rear.
4. Always plug heater directly into a wall outlet/receptacle. Never use with an
extension cord or relocatable power tap (outlet/power strip).
5. Check your heater cord and plug connections. A loose fitting outlet can
cause the plug to overheat and/or cause a fire. Be sure plug fits snugly in
the outlet. Check frequently during use to make sure plug and outlet are not
hot. If so, discontinue using heater and have outlet replaced by a qualified
electrician.
Note: Heater draw more current than small appliances, overheating of the
outlet may occur even if it has not occurred with the other appliances.
6. Always unplug the heater when not in use.
7. Do not operate heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner. Discard heater
or return to an authorized service facility for examination and/or repair.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners,
or similar coverings. Do not route cord under furniture of appliances. Keep
cord away from high traffic areas so it will not be tripped over.
9. Do not try to open or repair the heater yourself.
10. The surfaces of the heater may get hot when in use. To avoid burns, do not
touch the hot surfaces.
11. Close supervision is necessary when this unit is used by or near children,
invalids or disabled persons.
12. Do not use outdoors.
13. For Household Use Only.
14. Do not touch the control panel or plug with a wet hand.
15. Keep heater away from heated surfaces.
16. Plug must be plugged into an appropriate socket or outlet that is properly
installed. Improper connection can result in the risk of electric hazard.
17. To disconnect, turn all controls to the off position, then remove plug from outlet.
18. Always unplug the heater before moving or cleaning.
19. Always use the unit on a dry and level surface.
CAUTION: Read all instructions carefully before operating this
product. Retain this Owner’s Manual for future reference.
SAFETY PRECAUTIONS
4

PART DRAWING
5
8
9
10
11
12 12
16
16
12
19
18
18
20
21
7
17
15
15
12
14
13
16
22 23
1
23
4
5
6
21
20
11
16

PART LIST
6
No. Description Qty No. Description Qty
001 Remote Control 1 013 Remote Control Store Case 1
1etalPogoL4101etalPmunimulAlortnoC200
451x4MKtloB5101lenaPlortnoC300
618x3AWPtloB6101draoBlortnoCrewoP400
1hctiwSrewoPretsaM7101xoBlateM500
821x4MWPtloB8101teltuOriA600
121x4AWPtloB9101retaeHCTP700
6101x3AKtloB0201revoCraeRlateM800
2leehWretsaCraeR1201retliFriA900
1dnalGelbaC2201tenibaCdooW010
1droCrewoP3202leehWretsaCtnorF110
616x3MKtloB210

OPERATING INSTRUCTIONS
7
A: Control button layout
B: Temperature setting:
C: Time Setting: 0~ 8 hours
D: Operation:
Plug the power cord into an appropriate socket or outlet. Then press the
Master Power Switch to “ON” position on the rear of the heater and the
Power LED will light up on the control panel.
“Power (ON/OFF)” Button:
Power ON: Press and hold the Power (ON/OFF) button for 2-3 second to
turn on the power of the heater. The heater works on default setting of the
high temperature level performance.
Power OFF: Press the Power (ON/OFF) button to turn off the power of the
heater. All LED lights are off except the Power LED light. Then turn off the
master power switch on the rear of the heater.
“Mode” Button:
Press the Mode button to select Low Temperature Level Mode (I), Time Mode
(Time), Sleep Mode (Sleep), or High Temperature Level Mode (II).
Low Temperature Level Mode (I): Press the Mode button to select Low
Temperature Level Mode (I) when “I” LED lights up. The LED display will
“▲” or “▼” button to set the temperature. If no buttons are pressed for 3
seconds, it will switch to the current ambient temperature. Once you have set
the desired temperature, the heater will remain on until the ambient
temperature increases to the temperature that you set. The heater will off
automatically to maintain the desired ambient temperature. (Note: If the
current ambient temperature is greater than the set temperature, the function
will not operate.)
39 - 80 °F (4 - 27 °C)
show the default value of temperature as 80 °F (27 °C). You may press the

OPERATING INSTRUCTIONS
Time Mode (Time):Press the Mode button to select Time Mode (Time) when
“Time” LED lights up. The LED display will show the time that can be set.
You may press the “▲” or “▼” button to set the time. Each time you press
the “▲” or “▼” button, the time will increase or decrease by 1 Hr. If no
buttons are pressed for 3 seconds, it will switch to the current ambient
temperature. When pre-set time counts down to 0. The heater will off
automatically.
Sleep Mode (Sleep): Press the Mode button to select Sleep Mode (Sleep)
when “Sleep” LED lights up. The LED display will show the default value of
▲” or
“▼” button. If no buttons are pressed for 3 seconds, it will switch to the
current ambient temperature.
High Temperature Level Mode (II): Press the Mode button to select High
Temperature Level Mode (II) when “II” LED lights up. The LED display will
“▲” or “▼” button to set the temperature. If no buttons are pressed for 3
seconds, it will switch to the current ambient temperature. Once you have set
the desired temperature, the heater will remain on until the ambient
temperature increases to the temperature that you set. The heater will off
automatically to maintain the desired ambient temperature. (Note: If the
current ambient temperature is greater than the set temperature, the function
will not operate.)
Error codes on LED display:
E1: Temperature sensor is on short-circuit.
E2: Temperature sensor is on open-circuit.
E3:
Remote Control Button Instructions:
Power: Press Power button to turn on or off the
power of the heater.
Time increase and decrease: Used for setting
time.
TEMP increase and decrease: Used for setting
temperature.
High: Displays High Temperature Level Mode
(II).
Low: Displays Low Temperature Level Mode (I).
Sleep: Displays Sleep Mode (Sleep).
Button for alternating between Fahrenheit
and Celsius.
80 °F (27 °C)
130 °F
°F / °C
77 °F
8

Cleaning the Air Filter
The heater comes equipped with a washable air filter. It is easy to be cleaned.
We recommend the air filter to be cleaned once a month or if it appears to be
blocking airflow. To do this, please follow the below steps.
1. Loosen the bolt and remove it.
2. Gently remove the air filter from the rear of the
heater.
3. Clean the filter by running clean water on the opposite direction of the air
filter. You can also soak the air filter in water mixed with a small amount
of mild dish soap. Then rinse with water after soaking.
4. Please allow it to drip dry completely before reinstalling.
5. Do not use heater with without air filter assembly in place.
Storage
Store the heater in a clean and dry location when not in use.
MAINTENANCE
9
1. Press the Power (ON/OFF) button on the control panel to turn off the
power of the heater.
2. Turn off the master power switch on the rear of the heater.
3. Unplug the unit and wait until it is completely cool before clean.
4. To clean the heater, the outer surfaces of the heater may be cleaned with
a soft, damp cloth and any mild detergent if necessary. After cleaning,
dry the heater with a soft cloth.
CAUTION: Do not let liquid enter the heater.
5. Do not use abrasives or solvents to clean the heater. This may cause
damage to the surface of the heater.
6. Do not drop the heater in water.
7. Wait until the heater is completely dry before use.

Ordering Replacement Parts
Replacement parts can be ordered by calling or emailing our
customer service department
[e-mail]
1-866-924-1688
Monday through Friday, 8:00 AM - 5:00 PM (PST).
When ordering replacement parts please have the following
information ready:
1. Owner’s Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase
WARRANTY
10
Paradigm Health & Wellness, Inc. warrants to the original purchaser
that this product is free from defects in material and workmanship
when used for the purpose intended, under the conditions that it has
been installed and operated in according to Paradigm Health &
Wellness, Inc.’s Owner’s Manual. Paradigm Health & Wellness,
Inc.’s obligation under this warranty is limited to replacing free of
charge, any parts which may prove to be defective under normal
home use. This warranty does not include any damage caused by
improper operation, misuse or commercial application. From the
date of purchase, the product is warranted to be free from defects for
3 (three) years. Proof of purchase is required. This warranty is
offered only to the original owner and is not transferable.

Paradigm Health & Wellness, Inc.
PARTS REQUEST FAX FORM
Please fax this form to (1-626-810-2166)
OR YOU CAN EMAIL CUSTOMER SERVICE REQUESTS TO
[e-mail]
NAME: _______________________________________________________
ADDRESS: ____________________________________________________
CITY ______________ STATE ______________ ZIP ___________________
TELEPHONE: (Day) _____________________________________________
(Night) ____________________________________________
(Email Address) ____________________________________
SERIAL#: __________________________________________
MODEL#: __________________________________________
PURCHASE DATE: ______________________________________________
PURCHASE FROM: ______________________________________________
“YOUR ORDER WILL BE PROCESSED WITHIN 3 BUSINESS DAYS”
PART # DESCRIPTION QTY
OFFICIAL USE ONLY
SHIP DATE: ___________________________________________
TRK #: _______________________________________________
BACK ORDER: ________________________________________
FAX FORM
11