Paradox DGP-ACM12 User manual

Access Control Module V4.1
DGP-ACM12
Installation Instructions
paradox.com
Printed in Canada 09/2007 ACM12-EI01
Introduction
The Access Control Module (DGP-ACM12) is designed to be used with the
Digiplex EVO System control panels. Each DGP-ACM12 allows you to
connect a reader, a REX device, a door contact and a locking device to
control the access to one door. If desired, door contacts can also be assigned
to zones in the control panel to link the doors to the alarm system. This will
allow you to use the same door for the access control system and the alarm
system.
What’s New 4.1
• The backlight intensity defaults in sections [025] and [026] are now 003
What’s New 4.0
• Allows access with Card and Pin and Card or PIN when used with a
DGP-R915 or CR-R885-BL
• Allows arming with PIN or Card and PIN when used with a DGP-R915
• Transformer Sharing: Use one transformer to power multiple modules
with transformer sharing. Respect the maximum power output of the
transformer. See Figure 1 for more information.
Technical Specifications
Installation
The module is connected to the control panel’s combus as shown in Figure 1.
Please refer to the control panel’s Programming Guide for the maximum
installation distance. Devices connected to the PGM output must be
connected as shown in Figure 2. Refer to Figure 5 for connection drawings for
the REX device, reader, locking device and door contact.
The door contact follows the control panel’s EOL definition. When
EOL is enabled and the door contact is not used, place a 1k
9 resistor
across the CT and AUX- input terminals. If EOL is disabled, use a
jumper. If the REX device is not used, place a jumper across the REX
and AUX- terminals.
AC Power
Use a 16.5Vac (50/60 Hz) transformer with a minimum 20VA. as shown
in Figure 1. Do not use any switch-controlled outlets to power the
transformer.
Backup Battery
To power the module’s door lock relay during a power failure, connect a
12Vdc 4Ah rechargeable acid/lead or gell cell backup battery as shown in
Figure 1. Connect the battery after applying AC power.
Inverting the polarity when installing the battery will blow the battery
fuse.
Connecting the External Negative Trigger
The DGP-ACM12 comes with an external negative trigger. You can use a
PGM from the control panel or another module to release the access
control door lock. The external negative trigger can also be triggered
using a push-button. When the push button is pressed, the door will
unlock. The PGM or push-button must ground the negative trigger.
Connect the push-button as shown in Figure 2.
LED Display
AC (Green): On when receiving AC power.
BATT (Green): On when charging and during battery tests.
AUX (Yellow): On when auxiliary output is active.
ERROR (Red):Indicates a problem with the module.
RX (Green): Flashes when receiving information from the panel.
TX (Green): Flashes when transmitting information to the panel.
Connection Diagrams
Figure 1: Connecting the power and combus
Figure 2: Additional Connection Information
Figure 3: Connecting a 4-Wire Reader (DGP-R910 / DGP-R915)
Figure 4: Connecting a 7-Wire Routing Cable
Figure 5: Connecting Access Control Devices
Figure 6: Connecting for Firmware Upgrade (CONV4USB)
AC Power: 16Vac, 20/40VA, 50 - 60Hz
Aux. Power: 12Vdc, typical 600mA, 1A max.
Battery: 12Vdc, 4Ah minimum
No. of Outputs: 2; one 50mA PGM output, one form C relay rated at 5A/
28Vdc, N.O./N.C.
No. of Zones: 2 (Door Contact & REX device)
No. of Inputs: 2 (Negative Trigger & Tamper inputs)
Control Panel
Compatibility: Any DGP-848 control panel with access control
Any DGP-NE96 control panel
Any EVO control panel
Table 1: Special Display
Error RX TX Condition
ON OFF OFF Combus is shorted / No clock / No data
ON OFF ON Wrong data / Invalid Combus address
(Too many modules)
ON ON OFF Future Use
ON ON ON Combus lines reversed (YEL and
GRN)
Flash ---- ---- Combus power is too low
12Vdc
RechargeableBattery:
12V 4Ah min
Disconnect the battery before
replacing the fuse.
Combus
Digiplex/
Digiplex EVO
series control
panel
AUX switch:
Press to toggle the AUX output.
To metallic enclosure
Ground clamp
Cold water pipe
grounding
AWG #14 single
conductor solid
copper wire
From
transformer
Connect to another
module compatible with
transformer sharing
Transformer Sharing
Transformer Sharing: Use one transformer to power
multiple modules with transformer sharing.
And / Or
To PGM output
External Negative Trigger
External Tamper
Switch (N.C.)
PGM
Connected up to 300m
(1000ft) away.
If the DGP-ACM12 loses
communication with the
reader, it will show up as a
Module Fail to Com.
trouble.
DGP-R915
Reader ACM-12
1: RED to (+)
2: BLK to (-)
3: GRN to (D0)
4: YEL to (D1)
Only connect one reader per
DGP-ACM12
DGP-R910 (not shown) is connected the same way
If you use a routing cable, use a
shielded routing cable. Do not
connect the routing cable’s shield to
the reader’s shield. Only connect the
routing cable’s shield at the DGP-
ACM12.
Connect
Reader ACM-12
1: Red to (+)
2: Black to (-)
3: Green to (D0)
4: White to (D1)
5: Brown to (Beep)
6; Orange to (RED)
7: Yellow to (GREEN)
CR-R880-BL
Only connect one reader per
DGP-ACM12
CR-R885-BL (not shown) is connected the same way
Connected up to 152m
(500ft) away.
When connecting the diode to the door lock, be
sure to connect the cathode of the diode to the
positive (+) voltage and the anode to the negative
(-) voltage.
* = Follows control panel’s EOL definition.
** = If the door contact is not used, install a jumper or a
1k9resistor across the AUX-and CT terminals
depending on the control panel’s EOL definition.
*** = If the Request for Exit (REX) device is not used,
place a jumper across the AUX-and REX terminals.
Cathode
Anode
1N4007
Diode
*** REX device must be
connected to REX terminal
** Door contact
must be
connected to CT
terminal
No EOL required
on REX
CONV4USB
DGP-ACM12

U= Default setting
Only Event Groups 000 to 055, 062 and 063 can be used to program the module’s PGM.
Warranty
For complete warranty information onthis product please refer to the Limited Warranty Statement found on the website www.paradox.com/terms. Your use of the Paradox product signifies your acceptance of all
warranty terms and conditions.
We strongly advise that you review and take into consideration the “Limitations of Alarm Systems” document available on our website at http://paradox.com/Terms/.
© 2003-2007 Paradox Security Systems Ltd. All rights reserved. Specifications may changewithout prior notice. Oneor more of the following US patents may apply: 7046142, 6215399, 6111256, 6104319, 5920259,
5886632, 5721542, 5287111, 5119069, 5077549 and RE39406 and otherpending patentsmay apply. Canadian and internationalpatents may also apply.
Digiplex EVO is a trademark or registered trademark of Paradox Security Systems Ltd. or its affiliates in Canada, the United States and/or other countries.
Technical Support
For technical support in Canada or the U.S., call 1-800-791-1919, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST.
For technical support outside Canada and the U.S., call 00-1-450-491-7444, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST.
Please feel free to visit our website at www.paradox.com.
SECTION [001]: Partition Assignment SECTION [002]: General Options 1
Option OFF ON Option OFF ON
[1] Partition 1 NDisabled UEnabled [1] Tamper Input UDisabled NEnabled
[2] Partition 2 NDisabled UEnabled [2] Battery Charging Current U350mA N850mA
[3] Partition 3 NDisabled UEnabled [3] Reader’s red LED to follow partition’s
status NDisabled UEnabled
[4] Partition 4 NDisabled UEnabled [4] Reader’s beeping to follow partition’s
status when option [3] is ON NDisabled UEnabled
[5] Partition 5 NDisabled UEnabled [5] Card activates door unlocked schedule NDisabled UEnabled
[6] Partition 6 NDisabled UEnabled [6] Door will relock UImme-
diately NWhen
closed
[7] Partition 7 NDisabled UEnabled [7] Reader’s green LED for Access
Granted NDisabled UEnabled
[8] Partition 8 NDisabled UEnabled [8] Unlock on Request for Exit (REX) NDisabled UEnabled
SECTION [003]: General Options 2 SECTION [004]: PGM Options
Option OFF ON Option OFF ON
[1] Door Left Open Alarm UDisabled NEnabled [1] PGM Deactivation After U
Deactiva-
tion Event
N PGM Timer
[2] Door Left Open Pre-alarm NDisabled UEnabled [2] PGM Normal State UN.O. NN.C.
[3] Door Left Open Alarm NSilent UAudible [3] PGM Base Time U1 second N1 minute
[4] Door Left Open Alarm follows UAlarm
Restore NBeep
Timer [4] & [5] Special [4] [5]
[5] Door Forced Open Alarm UDisabled NEnabled NCard Only
NPIN Only
NCard and PIN
UCard or PIN
OFF
ON
OFF
ON
OFF
OFF
ON
ON
[6] Door Forced Alarm NSilent UAudible
[7] Door Forced Alarm follows UAlarm
Restore NBeep
Timer
[8] Reader Access Feedback NVisual UVisual &
audible [6] Reader Locate Feedback UVisual NVisual &
audible
[7] Unlock Door on Fire Alarm UDisabled NEnabled
[8] AC and Battery Supervision UEnabled NDisabled
Section Data Description Default
[005] __/__/__ (000 to 255 x 1 minute; 000 = Instant) AC failure report delay 030
[006] __/__/__ (001 to 255 seconds) Door Unlocked Period 005
[007] __/__/__ (001 to 255 seconds added to section [006]) Door Unlocked Period extension 015
[008] __/__/__ (001 to 255 seconds) Door Left Open Interval 060
[009] __/__/__ (001 to 255 seconds)
Time to start pre-alarm before alarm is triggered Door Left Open Pre-Alarm Timer 015
[010] __/__/__ (001 to 255 seconds) Beep timer for Door Left Open Alarm 005
[011] __/__/__ (001 to 255 seconds) Beep timer for Door Forced Open alarm 005
[012] __/__/__ (000 to 255; refer to option [3] in section [004]) PGM timer 005
[013] Door unlock schedule Start Time End Time S M T W T F S H
Schedule A: ___ ___ : ___ ___ ___ ___ : ___ ___ 1 2 3 4 5 6 7 8
Schedule B: ___ ___ : ___ ___ ___ ___ : ___ ___ 1 2 3 4 5 6 7 8
Event Group Feature Group Start # End #
Section Section Section Section
PGM Activation [014] __/__/__ [015] __/__/__ [016] __/__/__ [017] __/__/__
PGM Deactivation [018] __/__/__ [019] __/__/__ [020] __/__/__ [021] __/__/__
SECTION [022]: Safe Mode Options SECTION [031] PGM Options 2
Option OFF ON Option OFF ON
[1] Safe Mode NDisabled UEnabled [1] Flexible PGM Deactivation Option UPGM
Timer only
N Timer /
Deactivation
event
[2] Safe Mode Access NDisabled UEnabled [2] Reload Timer on Activation Event UDon’t
Reload NReload
Timer
[3] Reader Safe Mode Feedback UVisual N Visual &
audible [3] to [8] Future Use NN/A N N/A
[4] Unlock Door in Safe Mode UDisabled NEnabled
[5] Access Cards in Safe Mode USafe
Cards only NAny Cards
[6] to [8] Future Use NN/A N N/A
Section Data Description Default
[023] __/__/__ (001 to 024 hours; 000 = Disabled) Safe Mode Door Unlocked Period 000
[024] __/__/__ (001 to 255 seconds; 000 = Follow REX) REX Unlocked Period 000
[025] __/__/__ (000 to 003) Red LED Brightness 003
[026] __/__/__ (000 to 003) Green LED Brightness 003
[027] __/__/__ (000 to 003) Buzzer Frequency 001
[028] __/__/__ (000 to 255 minutes; 000 = instant) AC Restore Report Delay 005
[029] __/__/__ (000 to 255 minutes) Stay Lock Delay 000
[030] Test PGM: Activates the PGM for 8 seconds to verify if the PGM is functioning properly.
[032] __/__/__ (000 = steady, 001 to 254 = pulsed (increments of 8ms), 255 = pulsed fire) PGM Output type 000
[040] Access Card Serial Number Display: View an access card’s serial number displayed on any LCD or Grafica keypad on the combus.
When the DGP-ACM12 is in access card display mode, the door connected to the module cannot be accessed.
[061] Assign Safe Mode Access Card 1 (Present Card 3 Times)
[062] Assign Safe Mode Access Card 2 (Present Card 3 Times)
[063] Assign Safe Mode Access Card 3 (Present Card 3 Times)
[064] Assign Safe Mode Access Card 4 (Present Card 3 Times)
[070] Delete All Safe Mode Access Cards
[071] Delete Safe Mode Access Card 1
[072] Delete Safe Mode Access Card 2
[073] Delete Safe Mode Access Card 3
[074] Delete Safe Mode Access Card 4