Paradyne 3163 User manual

ACCULINK 3163 DSU/CSU
QUICK REFERENCE
Document No. 3163-A2-GL10-00

Copyright 1998 Paradyne Corporation.
All rights reserved.
Printed in U.S.A.
Notice
This publication is protected by federal copyright law. No part of this publication may be
copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated
into any human or computer language in any form or by any means, electronic,
mechanical, magnetic, manual or otherwise, or disclosed to third parties without the
express written permission of Paradyne Corporation, 8545 126th Ave. N., Largo,
FL 33773.
Paradyne Corporation makes no representation or warranties with respect to the
contents hereof and specifically disclaims any implied warranties of merchantability or
fitness for a particular purpose. Further, Paradyne Corporation reserves the right to
revise this publication and to make changes from time to time in the contents hereof
without obligation of Paradyne Corporation to notify any person of such revision or
changes.
Changes and enhancements to the product and to the information herein will be
documented and issued as a new release to this manual.
Warranty, Sales, and Service Information
Contact your local sales representative, service representative, or distributor directly for
any help needed. For additional information concerning warranty, sales, service, repair,
installation, documentation, training, distributor locations, or Paradyne worldwide office
locations, use one of the following methods:
Via the Internet: Visit the Paradyne World Wide Web site at
http://www.paradyne.com
Via Telephone: Call our automated call system to receive current information via
fax or to speak with a company representative.
— Within the U.S.A., call 1-800-870-2221
— Outside the U.S.A, call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail them
to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773,
or send e-mail to [email protected]. Include the number and title of this
document in your correspondence. Please include your name and phone number if you
are willing to provide additional clarification.
Trademarks
All products and services mentioned herein are the trademarks, service marks,
registered trademarks or registered service marks of their respective owners.

TM
1
ACCULINK 3163 DSU/CSU
Quick Reference
Document Number 3163-A2-GL10-00
December 1998
Product Documentation on the World Wide Web
We provide complete product documentation online. This lets you search the
documentation for specific topics and print only what you need, reducing the waste of
surplus printing. It also helps us maintain competitive prices for our products.
Complete documentation for this product is available at www.paradyne.com. Select
Service & Support → Technical Manuals → T1/E1 Digital Access Devices.
Select the following document:
Document No. 3163-A2-GB20
ACCULINK 3163 Data Service Unit/Channel Service Unit User’s Guide
To request a paper copy of a Paradyne document:
Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)
Outside the U.S.A., call 1-727-530-8623
Before installing the DSU/CSU, read the
Important Safety Instructions beginning on
page 13.
Quick Start Procedure
The following procedure is for experienced DSU/CSU users who are familiar with the
3163 DSU/CSU installation process and have no special requirements for their
application. See the
ACCULINK 3163 Data Service Unit/Channel Service Unit User’s
Guide
for more information.
1. If ac power is to be used, attach the power cord to the rear of the DSU/CSU and
the power transformer to a grounded 100 Vac power outlet. For information about
the optional dc power cable for a +24 Vdc or –48 Vdc power source, see the User’s
Guide.
2. Attach the 3163 DSU/CSU network connection to the T1 network using the
appropriate cable. Attach the 3163 DSU/CSU to the customer premises equipment
via the port connector.
3. Power on the DSU/CSU to perform the power-up self-test.
4. If you intend to use front panel emulation, connect the cable from the PC to the
COM port on the rear panel of the DSU/CSU.

2
5. The Factory 1 configuration for ESF framing format and B8ZS line coding format is
the default configuration and is appropriate for most networks. If this configuration
does not work for you, try the Factory 2 configuration for D4 framing format and
AMI line coding format. To further customize configuration options, refer to the
configuration option tables beginning on page 4.
6. During the power-up self-test, the FAIL LED flashes, then all LEDs blink twice.
When the test is complete, verify that the DSU/CSU is functional by observing that
the OK and NETWORK SIG LEDs are lit.
PORT 1 COM PORT MODEM
POWER NETWORK
CAUTION: AUX PORTOR COM PORT MUST NOT BE CONNECTED TO PSTN OR T1 NETWORK
NEC
PORT 1 COM PORT MODEM
POWER NETWORK
CAUTION: AUX PORTOR COM PORT MUST NOT BE CONNECTED TO PSTN OR T1 NETWORK
NEC
98-15941a
PSTN
Modem
Power
Modem
Power
Front
Panel
3163 DSU/CSU
3163
DSU/CSU
3163
DSU/CSU
Serial
Port
or
COM
Port Network Port
Modem
Port
COM
Port Network Port
Modem
Port
Network
Port
PC
T1 or Serial Connections
Dial Connections
Terminal
Terminal
or
T1 Network
Cabling Examples

3
Configuration Options
Configuration options are accessed from the Configuration branch of the front panel
menu.
DSU ESF
98-15943a
Stat
DevHS STest Perf TStat LED ID
T1 PrtnPrtnUserTelco
Cur 24Tot Intvl FarNear
Cur 8Tot Intvl
Load EditArea From:
Choose Function:
Activ Cust1 Cust2 Fact1 Fact2
User AlarmNETPort Chan Gen Mgmt
Gen
Save
Cust1Activ Cust2
Edit
Cnfig
Prt1ClearDsply
Ctrl
Rel ClrReg ResetCID PasswdDLCall
DiscDialPass ChDir
1 .. 5,A
(Directory)
1 .. 5,A
(Directory)
User Prt1
Test
Rlpbk Lpbk Ptrns Lamp
QRSS 511
Abort Mon
LLBUP
LLBDN
54UP
54DN
FT1UP
FT1DN
PLBRLB
LLB
Abort DCLB
DTLB
QRSS1in8 511
Send

4
Factory default configuration options are shown in boldface type in the following tables.
Table 1. Port Configuration Options (1 of 2)
Option Factory 1 Factory 2 Comments/Description
E530 E530
Port Type:
V.35 V.35 Selects the port t
y
pe: EIA-530A
,
Port Type: RS449 RS449
Selects
the
ort
ty e:
EIA
-
530A
,
V.35, RS449, or X.21.
X.21 X.21
Base Rate:
Nx64 Nx64 Enables the port to either Nx56 or
Base Rate: Nx56 Nx56
Enables
the
ort
to
either
Nx56
or
Nx64 rates.
Disab Disab
Net DCLB:
V.54 V.54 Network-initiated DCLB, allows
DCLB t b t ll d b i b d
Net DCLB: FT1 FT1 DCLB to be controlled by inband
V.54 or FT1 (ANSI) codes.
Both Both
Disab Disab
Port LB:
DTLB DTLB Port-initiated Loopbacks, allows
L b k t b i iti t d th h
Port LB: DCLB DCLB Loopbacks to be initiated through
the port by the external DTE.
Both Both
y
Disab Disab
All Ones:
DTR DTR All ones sent to network
(
DTE
)
T1
All Ones: RTS RTS
All
ones
sent
to
network
(DTE)
T1
when DTR or RTS interrupted.
Both Both
Rcv Yellow: None None Data port remains enabled, or is
di bl d i i Y ll
Rcv
Yellow:
(Received Yellow) Halt Halt disabled, on receiving Yellow on
network T1.
Tx Clock:
Int Int Selects whether the transmitted
d t l k i i t l (TXC)
Tx Clock: Ext Ext data clock is internal (TXC) or
external (XTXC).
InvertTxC: Enab Enab Selects phase inversion of the
InvertTxC:
(Invert Tx Clock) Disab Disab
Selects
hase
inversion
of
the
transmit clock (TXC).
InvertData:
Enab Enab Allows the data on the port to be
InvertData: Disab Disab
Allows
the
data
on
the
ort
to
be
inverted.

5
Table 2. Network Interface Configuration Options
Option Factory 1 Factory 2 Comments/Description
NET Framing:
D4 D4
Selects D4 or ESF framing format
NET Framing: ESF ESF Selects D4 or ESF framing format.
NET Coding:
AMI AMI Selects AMI or B8ZS line coding
NET Coding: B8ZS B8ZS
Selects
AMI
or
B8ZS
line
coding
format.
0.0 0.0
LBO:
–7.5 –7.5
Provides Line Build Out in dB
LBO: –15 –15 Provides Line Build Out in dB.
–22.5 –22.5
ANSI PRM:
Enab Enab Sends ANSI Performance Report
ANSI PRM: Disab Disab
Sends
ANSI
Performance
Re ort
Messages.
Mgmt Link:
Disab Disab Specifies whether the FDL’s
Mgmt Link: SNMP SNMP
S ecifies
whether
the
FDLs
Management Link is enabled.
NET LLB:
Enab Enab Network-initiatedLLB allows LLB to
NET LLB: Disab Disab
Network initiated
LLB
allows
LLB
to
be controlled by inband LLB codes.
NET PLB:
Enab Enab Network-initiated PLB allows PLB
to be controlled by FDL PLB
NET PLB: Disab Disab to be controlled by FDL PLB
messages.
62411 62411 Provides enforcement of ones
d i i AT&T TR
BitStuff: Part68 Part68 density protection per AT&T TR
62411, ANSI T1
-
403, and FCC
Disab Disab
62411
,
ANSI
T1
-
403
, an
d
FCC
Part 68 Technical Publication.
Circuit Ident: Edit Edit Specifies the transmission vendor’s
Circuit
Ident:
Clear Clear
S ecifies
the
transmission
vendor s
circuit identifier.

6
Table 3. Channel Configuration Options (1 of 2)
Option Factory 1 Factory 2 Comments/Description
Block Block
Determines how channels are
Assign By: ACAMI ACAMI Determines how channels are
assigned: contiguous blocks,
C
gy
Chan Chan
gg ,
ACAMI or individual channels.
Port Rate:
64 (56)
128 (112)
192 (168)
256 (224)
320 (280)
384 (336)
448 (392)
512 (448)
576 (504)
640 (560)
704 (616)
768 (672)
832 (728)
896 (784)
960 (840)
1024 (896)
1088 (952)
1152 (1008)
1216 (1064)
1280 (1120)
1344 (1176)
1408 (1232)
1472 (1288)
1536 (1344)
64 (56)
128 (112)
192 (168)
256 (224)
320 (280)
384 (336)
448 (392)
512 (448)
576 (504)
640 (560)
704 (616)
768 (672)
832 (728)
896 (784)
960 (840)
1024 (896)
1088 (952)
1152 (1008)
1216 (1064)
1280 (1120)
1344 (1176)
1408 (1232)
1472 (1288)
1536 (1344)
Selects the data rate for the port.
The possible rates depend on
whether the port is configured for
Nx56 or Nx64.
This configuration option only
appears if the “Assigned By”
configuration option is Block or
ACAMI.

7
Table 3. Channel Configuration Options (2 of 2)
Option Factory 1 Factory 2 Comments/Description
Clear Clear Clears (unassigns) channels for
this port.
Start At:
N1 (D1)
N2 (D2)
N3 (D3)
N4 (D4)
N5 (D5)
N6 (D6)
N7 (D7)
N8 (D8)
N9 (D9)
N10 (D10)
N11 (D11)
N12 (D12)
N13 (D13)
N14 (D14)
N15 (D15)
N16 (D16)
N17 (D17)
N18 (D18)
N19 (D19)
N20 (D20)
N21 (D21)
N22 (D22)
N23 (D23)
N24 (D24)
N1 (D1)
N2 (D2)
N3 (D3)
N4 (D4)
N5 (D5)
N6 (D6)
N7 (D7)
N8 (D8)
N9 (D9)
N10 (D10)
N11 (D11)
N12 (D12)
N13 (D13)
N14 (D14)
N15 (D15)
N16 (D16)
N17 (D17)
N18 (D18)
N19 (D19)
N20 (D20)
N21 (D21)
N22 (D22)
N23 (D23)
N24 (D24)
This configuration option appears if
the “Assigned By” configuration
option is Block or ACAMI.
Line 1 Displays: Line 2 Displays: Meaning Comments/Description
— Unassigned
N1 N2 N3 ...... N24: Prt1 Channel assigned
to port 1 This configuration option appears if
the “Assigned By” configuration
option is individual channels
N1
N2
N3
......
N24:
(If assigned to NET)
D1 D2 D3 ..... D24:
(If assigned to DTE)
D1, D2 ... D24 Channel assigned
to this DTE
channel
option is individual channels
(Chan).
Function key under the channel
(If
ass
i
gne
d
t
o
DTE)
N1, N2 ... N24 Channel assigned
to this NET
channel
Function
key
under
the
channel
(N1, N2 etc.) assigns (unassigns)
port (1, 2, 3, or 4) to that channel.

8
Table 4. General Configuration Options
Option Factory 1 Factory 2 Comments/Description
NET NET
Clock Src:
DTE DTE Selects the clock source to be
dth tlkfth
Clock Src: Prt1 Prt1 used as the master clock for the
DSU/CSU.
Int Int
SU/CSU
Tst Timeout
Enab Enab Specifies whether the durations of
i iti t d t t li it d b
Tst Timeout Disab Disab user-initiated tests are limited by
Tst Duration.
10 10
Tst Duration
Up Up Specifies the duration of
iii dl b k d
T
s
t
D
ura
ti
on
Down Down user-initiated loopback and pattern
tests.
Save Save
Table 5. User Configuration Options (1 of 3)
Option Factory 1 Factory 2 Comments/Description
Self Test:
Enab Enab Allows b
y
pass of self-test on
Self-Test: Disab Disab
Allows
by ass
of
self-test
on
initialization.
FP Access:
Enab Enab Controls whether front panel
FP Access: Disab Disab
Controls
whether
front
anel
access or display is allowed.
FP Pass:
Enab Enab Controls whether front panel
FP Pass: Disab Disab
Controls
whether
front
anel
pass-through is allowed.
Dial In:
Enab Enab Controls whether dial-in access is
Dial-In: Disab Disab
Controls
whether
dial-in
access
is
allowed.
None None
Password:
Com Com Controls whether a password is
Password: Modem Modem
Controls
whether
a
assword
is
required during a call setup.
Both Both
Mgmt Mgmt
Com Use: ASCII ASCII Controls how the COM port is
used.
Term Term
used
.
Com Ty
p
e:
Async Async Controls whether the COM port is
Com Type: Sync Sync
Controls
whether
the
COM
ort
is
synchronous or asynchronous.