Paradyne 9126 User manual

FrameSaver®SLV
9126, 9126-II, and 9128-II CSU/DSU,
and 9126-II Router
User’s Guide
Document No. 9128-A2-GB20-80
September 2002

ASeptember 2002 9128-A2-GB20-80
Copyright © 2002 Paradyne Corporation.
All rights reserved.
Printed in U.S.A.
Notice
This publication is protected by federal copyright law. No part of this publication may be copied or distributed,
transmitted, transcribed, stored in a retrievalsystem, or translated into any human or computer language in any form or
by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express
written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.
Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation
reserves the right to revise this publication and to make changes from time to time in the contents hereof without
obligation of Paradyne Corporation to notify any person of such revision or changes.
Changes and enhancements to the product and to the information herein will be documented and issued as a new
release to this manual.
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor directly for any help needed. For additional
information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or
Paradyne worldwide office locations, use one of the following methods:

Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at
www.paradyne.com/warranty.)

Telephone: Call our automated system to receive current information by fax or to speak with a company
representative.
—Within the U.S.A., call 1-800-870-2221
—Outside the U.S.A., call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail them to Technical Publications,
Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to [e-mail]. Include the
number and title of this document in your correspondence. Please include your name and phone number if you are
willing to provide additional clarification.
Trademarks
ACCULINK, COMSPHERE, FrameSaver, Hotwire, MVL, NextEDGE, OpenLane, and Performance Wizard are
registered trademarks of Paradyne Corporation.GranDSLAM, GrandVIEW, ReachDSL, and TruePut are trademarks of
Paradyne Corporation. All otherproducts and services mentioned herein are the trademarks, service marks, registered
trademarks, or registered service marks of their respective owners.
Patent Notification
FrameSaver products are protected by U.S. Patents: 5,550,700 and 5,654,966. Other patents are pending.

9128-A2-GB20-80 September 2002 i
Contents
About This Guide

Purpose and Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

Document Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

Product-Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii

Conventions Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
1 About the FrameSaver SLV

System Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
CSU/DSU-Specific Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Router-Specific Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

FrameSaver Diagnostic and SLM Feature Sets. . . . . . . . . . . . . . . . . . 1-4

FrameSaver Diagnostic Feature Set . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Additional FrameSaver SLV9126-II and 9128-II Features. . . . . . . 1-9
Additional FrameSaver SLV 9128-II Features. . . . . . . . . . . . . . . . 1-9

FrameSaver SLM Feature Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

OpenLane SLM System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

NetScout Manager Plus and NetScout Probes . . . . . . . . . . . . . . . . . . 1-12
2 User Interface and Basic Operation

Logging On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Screen Work Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Navigating the Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Keyboard Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Selecting from a Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Switching Between Screen Areas . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Selecting a Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Entering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Screen Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Navigating the Router’s CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
CLI Keyboard Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Contents
ii September 2002 9128-A2-GB20-80
3 Configuration Procedures

Basic Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Configuration Option Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Accessing and Displaying Configuration Options . . . . . . . . . . . . . 3-4
Changing Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Saving Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
4 Configuration Options

Using the Easy Install Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Using RIP with FrameSaver SLV CSU/DSUs . . . . . . . . . . . . . . . . . . . 4-4

Entering System Information and Setting the System Clock . . . . . . . . 4-5

Setting Up the Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Setting Up Call Directories for Trap Dial-Out. . . . . . . . . . . . . . . . . 4-6
Setting Up to Use the Modem PassThru Feature . . . . . . . . . . . . . 4-7

Setting Up Auto-Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Selecting a Frame Relay Discovery Mode. . . . . . . . . . . . . . . . . . . 4-9
Automatically Removing a Circuit . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Setting Up Dial Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Setting Up the DBM Physical Interface . . . . . . . . . . . . . . . . . . . . . 4-12
Setting Up Automatic Backup Configuration . . . . . . . . . . . . . . . . . 4-13
Modifying ISDN Link Profiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Restricting Automatic Backup and Configuring Backup Timers . . 4-17
Configuring the DBM Interface to Send SNMP Traps . . . . . . . . . . 4-18
Assigning DLCIs to a Backup Group. . . . . . . . . . . . . . . . . . . . . . . 4-18

PVC Backup Over the Network Interface. . . . . . . . . . . . . . . . . . . . . . . 4-19

Setting Up Back-to-Back Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
Changing Operating Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19

Configuration Option Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

Configuring the Overall System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
Configuring Frame Relay and LMI for the System (CSU/DSUs) . . 4-21
Configuring Class of Service Definitions . . . . . . . . . . . . . . . . . . . . 4-25
Code Point Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27
Configuring Service Level Verification Options . . . . . . . . . . . . . . . 4-28
Configuring General System Options . . . . . . . . . . . . . . . . . . . . . . 4-31

Configuring Physical Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34
Configuring the Network Interface. . . . . . . . . . . . . . . . . . . . . . . . . 4-34
Configuring a User Data Port (CSU/DSUs). . . . . . . . . . . . . . . . . . 4-38
Configuring the DSX-1 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . 4-43
Configuring the ISDN DBM Interface. . . . . . . . . . . . . . . . . . . . . . . 4-45
Setting Up ISDN Link Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-49

Contents
9128-A2-GB20-80 September 2002 iii

Assigning Time Slots/Cross Connections . . . . . . . . . . . . . . . . . . . . . . 4-51
Assigning Frame Relay Time Slots to the Network Interface . . . . 4-52
Assigning DSX-1 Time Slots to the Network Interface . . . . . . . . . 4-53
Assigning a Synchronous Data Port to Network or DSX-1
Time Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-59
Clearing Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-60

Configuring Frame Relay for an Interface . . . . . . . . . . . . . . . . . . . . . . 4-61

Manually Configuring DLCI Records . . . . . . . . . . . . . . . . . . . . . . . . . . 4-64

Configuring PVC Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-68

Configuring the IP Path List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-72

Setting Up Management and Communication Options . . . . . . . . . . . . 4-73
Configuring Node IP Information . . . . . . . . . . . . . . . . . . . . . . . . . . 4-74
Configuring Management PVCs . . . . . . . . . . . . . . . . . . . . . . . . . . 4-77
Configuring General SNMP Management . . . . . . . . . . . . . . . . . . . 4-83
Configuring Telnet and/or FTP Session Support. . . . . . . . . . . . . . 4-84
Configuring SNMP NMS Security . . . . . . . . . . . . . . . . . . . . . . . . . 4-87
Configuring SNMP Traps and Trap Dial-Out. . . . . . . . . . . . . . . . . 4-88
Configuring Ethernet Management . . . . . . . . . . . . . . . . . . . . . . . . 4-94
Configuring the Communication Port. . . . . . . . . . . . . . . . . . . . . . . 4-96
Configuring the Modem Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-100

Configuring the Criteria for Automatic Backup. . . . . . . . . . . . . . . . . . . 4-104
5 Configuring the FrameSaver SLV Router

FrameSaver SLV Router Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

IP Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Address Resolution Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Proxy ARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Interface Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Network Address Translation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
IP Options Processing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Applications Supported by NAT. . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
NAT Configuration Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Network Address Port Translation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
NAPT Configuration Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
NAT and NAPT Configuration Example. . . . . . . . . . . . . . . . . . . . . 5-10

Dynamic Host Configuration Protocol Server. . . . . . . . . . . . . . . . . . . . 5-11
DHCP Server with NAT Configuration Example . . . . . . . . . . . . . . 5-12
DHCP Server at Remote Site Configuration Example. . . . . . . . . . 5-13

DHCP Relay Agent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13

Contents
iv September 2002 9128-A2-GB20-80

Router Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
IP Router Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
Bridge Filtering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
IP Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
Land Bug Prevention. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
Smurf Attack Prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15

Provisioning the Router Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15

Configuring the Router Using Terminal Emulation. . . . . . . . . . . . . . . . 5-16
Uploading and Downloading the Router Configuration Via the CLI 5-16
6 Security and Logins

Limiting Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Controlling Asynchronous Terminal Access. . . . . . . . . . . . . . . . . . . . . 6-2

Limiting Dial-In Access via the Modem Port. . . . . . . . . . . . . . . . . . . . . 6-4

Controlling ISDN Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
ISDN Call Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Disabling ISDN Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Controlling Telnet or FTP Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Limiting Telnet Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Limiting FTP Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Limiting Telnet or FTP Access Over the TS Access Management
Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

Controlling SNMP Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Disabling SNMP Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Assigning SNMP Community Names and Access Levels. . . . . . . 6-10
Limiting SNMP Access Through IP Addresses . . . . . . . . . . . . . . . 6-11

Creating a Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12

Modifying a Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13

Deleting a Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13

Controlling Router CLI Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
Access Levels (Command Modes) . . . . . . . . . . . . . . . . . . . . . . . . 6-14
Changing Access Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15
7 Operation and Maintenance

Displaying System Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

Viewing LEDs and Control Leads . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
FrameSaver SLV 9126 LEDs and Control Leads . . . . . . . . . . . . . 7-5
FrameSaver SLV 9128-II LEDs and Control Leads. . . . . . . . . . . . 7-7
LED Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Control Lead Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11

Device Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12

Contents
9128-A2-GB20-80 September 2002 v

Status Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-18
System and Test Status Messages. . . . . . . . . . . . . . . . . . . . . . . . 7-19
Network LMI-Reported DLCIs Status . . . . . . . . . . . . . . . . . . . . . . 7-29
IP Path Connection Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-31
PVC Connection Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-33
Time Slot Assignment Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-36
DBM Interface Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-38

IP Routing Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-48

Performance Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-50
Clearing Performance Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . 7-51
Service Level Verification Performance Statistics . . . . . . . . . . . . . 7-52
DLCI Performance Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-57
Additional Performance Statistics for IP Enabled DLCI. . . . . . . . . 7-59
Frame Relay Performance Statistics. . . . . . . . . . . . . . . . . . . . . . . 7-60
ESF Line Performance Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . 7-64
DBM Call Performance Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . 7-67
Ethernet Performance Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . 7-68

Trap Event Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-69

Modem Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-70
Activating the Modem PassThru Feature . . . . . . . . . . . . . . . . . . . 7-70
Canceling Modem PassThru Operation. . . . . . . . . . . . . . . . . . . . . 7-70
Manually Disconnecting the Modem . . . . . . . . . . . . . . . . . . . . . . . 7-71
Verifying Modem Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-71

ISDN DBM Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-72
Forcing Backup (Disruptive) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-72
Placing a Test Call (Nondisruptive) . . . . . . . . . . . . . . . . . . . . . . . . 7-73
Verifying ISDN Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-74
Verifying That Backup Can Take Place. . . . . . . . . . . . . . . . . . . . . 7-74

FTP File Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-75
Upgrading System Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-77
Upgrading ISDN BRI DBM Software . . . . . . . . . . . . . . . . . . . . . . . 7-78
Determining Whether a Download Is Completed. . . . . . . . . . . . . . 7-79
Changing Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-79
Transferring Collected Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-80

Turning Off the System Alarm Relay . . . . . . . . . . . . . . . . . . . . . . . . . . 7-81
8 Troubleshooting

Problem Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

Resetting the Unit and Restoring Communication. . . . . . . . . . . . . . . . 8-3
Resetting the Unit from the Control Menu . . . . . . . . . . . . . . . . . . . 8-3
Resetting the Unit By Cycling the Power. . . . . . . . . . . . . . . . . . . . 8-3
Restoring Communication with an Improperly Configured Unit. . . 8-4

Contents
vi September 2002 9128-A2-GB20-80

Troubleshooting Management Link Feature . . . . . . . . . . . . . . . . . . . . 8-5

LMI Packet Capture Utility Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
Viewing Captured Packets from the Menu-Driven User Interface. 8-6

Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

Viewing the Trap Event Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14

Troubleshooting Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14
Device Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14
Frame Relay PVC Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
ISDN DBM Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17

Tests Available. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18
Test Timeout Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19
DBM Tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19

Starting and Stopping a Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20
Aborting All Tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21

PVC Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22
PVC Loopback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23
Send Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24
Monitor Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24
Connectivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-25
Test Call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-25

Physical Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26
Line Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-27
Payload Loopback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-28
Repeater Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-29
DTE Loopback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-30
Send Line Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-31
Data Channel Loopbacks on a Frame Relay Link. . . . . . . . . . . . . 8-32
Send Remote Line Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-33
Send and Monitor Pattern Tests . . . . . . . . . . . . . . . . . . . . . . . . . . 8-34

IP Ping Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-35
IP Ping Test –Procedure 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-39
IP Ping Test –Procedure 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-40

Lamp Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-40
9 Setting Up OpenLane for FrameSaver Devices and
Activating SLM Features

OpenLane Support of FrameSaver Devices . . . . . . . . . . . . . . . . . . . . 9-2

Setting Up the OpenLane SLM System . . . . . . . . . . . . . . . . . . . . . . . . 9-2

Setting Up FrameSaver Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

Ordering SLM Feature Set Activations. . . . . . . . . . . . . . . . . . . . . . . . . 9-4
To Find Your License Key Number . . . . . . . . . . . . . . . . . . . . . . . . 9-4
The Activation Certificate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

Contents
9128-A2-GB20-80 September 2002 vii

Administering and Managing SLM Activations. . . . . . . . . . . . . . . . . . . 9-6
Entering an Activation Certificate. . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Checking Activation Certificate Status. . . . . . . . . . . . . . . . . . . . . . 9-7
Scheduling Activations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Checking the Status of Scheduled Activations . . . . . . . . . . . . . . . 9-9
Canceling Scheduled Activations . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Accessing and Printing the Certificate Summary Report. . . . . . . . 9-9
10 Setting Up NetScout Manager Plus for FrameSaver Devices

Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

Configuring NetScout Manager Plus . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
Adding FrameSaver SLV Units to the NetScout Manager Plus
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4
Verifying Domains and Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5
Correcting Domains and Groups . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
Adding SLV Alarms Using a Template . . . . . . . . . . . . . . . . . . . . . 10-8
Editing Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9
Adding SLV Alarms Manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
Creating History Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-13
Installing the User-Defined History Files . . . . . . . . . . . . . . . . . . . . 10-15

Monitoring a DLCI’s History Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-16

Monitoring the Agent Using NetScout Manager Plus. . . . . . . . . . . . . . 10-18

Statistical Windows Supported. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20
11 Setting Up Network Health for FrameSaver Devices

Installation and Setup of Network Health. . . . . . . . . . . . . . . . . . . . . . . 11-2

Discovering FrameSaver Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3

Configuring the Discovered Elements . . . . . . . . . . . . . . . . . . . . . . . . . 11-4

Grouping Elements for Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5

Generating Reports for a Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6
About Service Level Reports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6
About At-a-Glance Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6
About Trend Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7
Printed Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7

Reports Applicable to SLV Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7
A Menu Hierarchy

Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Contents
viii September 2002 9128-A2-GB20-80
B SNMP MIBs and Traps, and RMON Alarm Defaults

MIB Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2

Downloading MIBs and SNMP Traps. . . . . . . . . . . . . . . . . . . . . . . . . . B-2

System Group (mib-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3
FrameSaver Unit’s sysDescr (system 1) . . . . . . . . . . . . . . . . . . . . B-3
FrameSaver Unit’s sysObjectID (system 2). . . . . . . . . . . . . . . . . . B-3

Interfaces Group (mib-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3
Paradyne Indexes to the Interface Table (ifTable). . . . . . . . . . . . . B-3
NetScout Indexes to the Interface Table (ifTable). . . . . . . . . . . . . B-6

Standards Compliance for SNMP Traps . . . . . . . . . . . . . . . . . . . . . . . B-8
Trap: warmStart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9
Trap: authenticationFailure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9
Traps: linkUp and linkDown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10
Traps: enterprise-Specific . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-13
Traps: RMON-Specific. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-16
Trap: dialControl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-17

RMON Alarm and Event Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-18
Physical Interface Alarm Defaults . . . . . . . . . . . . . . . . . . . . . . . . . B-19
Frame Relay Link Alarm Defaults . . . . . . . . . . . . . . . . . . . . . . . . . B-20
DLCI Alarm Defaults –Paradyne Area . . . . . . . . . . . . . . . . . . . . . B-22
DLCI Alarm Defaults –NetScout Area. . . . . . . . . . . . . . . . . . . . . . B-23

Object ID Cross-References (Numeric Order) . . . . . . . . . . . . . . . . . . . B-26
C Router CLI Commands, Codes, and Designations

CLI Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
Pager Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3
Access Control Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3
Configuration Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4
Interface Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
IP Routing Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8
Bridge Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-9
ARP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-11
NAT Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-12
DHCP Server Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-15
DHCP Relay Agent Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . C-18
Filter (access-list) Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . C-19
Diagnostic Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-23
Show Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-25

Ethernet Type Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-29

Contents
9128-A2-GB20-80 September 2002 ix

Protocol and Port Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-31
ICMP Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-31
TCP Port Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-33
UDP Port Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-34
D Router Command Line Summaries and Shortcuts

CLI Summaries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
Show Command Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2
Access Control and System Level Command Summary. . . . . . . . D-3
CLI Command Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-4
CLI Command Default Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . D-6
E Connectors, Cables, and Pin Assignments

Rear Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1

COM Port Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-4
COM Port for 9126 and 9128-II (25-Position) . . . . . . . . . . . . . . . . E-4
COM Port for 9126-II (9-Position) . . . . . . . . . . . . . . . . . . . . . . . . . E-4
COM Port for 9128-II Carrier Mount . . . . . . . . . . . . . . . . . . . . . . . E-5
COM Port-to-PC Cable (Feature No. 3100-F2-550) . . . . . . . . . . . E-5
COM Port-to-Terminal/Printer Cable (Feature No. 3100-F2-540) . E-6
COM Port-to-Router Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-7
Gender Adapter/Changer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-10
LAN Adapter Converter and Cable . . . . . . . . . . . . . . . . . . . . . . . . E-10

DTE Port Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-11
Standard V.35 Straight-through Cable. . . . . . . . . . . . . . . . . . . . . . E-12
Standard V.35 Crossover Cable . . . . . . . . . . . . . . . . . . . . . . . . . . E-12

DSX-1 Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-13
DSX-1 Port for 9126, 9126-II, and Carrier Mounted 9128-II
(8-Position) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-13
DSX-1 Adapter (Feature No. 9008-F1-560). . . . . . . . . . . . . . . . . . E-13
DSX-1 Port for 1-Slot 9128-II (15-Position) . . . . . . . . . . . . . . . . . . E-14

T1 Network Cable (Feature No. 3100-F1-500) . . . . . . . . . . . . . . . . . . E-15
T1 Mass Termination Cable (Feature No. 9007-F1-500). . . . . . . . E-15
Canadian T1 Line Interface Cable (Feature No. 3100-F1-510). . . E-16

Ethernet Port Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-16

Modem Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-17

ISDN DBM Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-17
ISDN Modular Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-17

Contents
xSeptember 2002 9128-A2-GB20-80
F Technical Specifications
G Equipment List

Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-1

Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-6
Index

9128-A2-GB20-80 September 2002 xi
About This Guide
Purpose and Intended Audience
This document contains information needed to properly set up, configure, and
verify operation of the FrameSaver SLV (Service Level Verifier) 9126, 9126-II, and
9128-II CSU/DSU, and 9126-II Router running firmware release 2.0.3 or above. It
is intended for system designers, engineers, administrators, and operators.
You must be familiar with the functional operation of digital data communications
equipment and frame relay networks.
Document Organization
Section Description
Chapter 1, About the FrameSaver
SLV
Identifies how the FrameSaver SLV 9126, 9126-II,
and 9128-II CSU/DSU, and 9126-II Router, fit into
Paradyne’s Service Level Management (SLM)
solution, and describes their features.
Chapter 2,
User Interface and
Basic Operation
Shows how to navigate the menu-driven user
interface.
Chapter 3,
Configuration
Procedures
Shows how to access and save configuration options.
Chapter 4,
Configuration Options Provides configuration information for the
FrameSaver SLV 9126, 9126-II, and 9128-II
CSU/DSU, and 9126-II Router.
Chapter 5,
Configuring the
FrameSaver SLV Router
Describes the router’s interfaces and features, and
shows typical setups and configurations.
Chapter 6,
Security and Logins Provides procedures for controlling access to the
FrameSaver SLV and setting up logins.
Chapter 7,
Operation and
Maintenance
Provides procedures to display unit identification
information and perform file transfers, as well as how
to display and interpret status and statistical
information.
Chapter 8,
Troubleshooting Provides device problem resolution, alarm, and other
information, as well as troubleshooting and test
procedures.

About This Guide
xii September 2002 9128-A2-GB20-80
A master glossary of terms and acronyms used in Paradyne documents is
available on the World Wide Web at www.paradyne.com. Select
Library
→
Technical Manuals
→
Technical Glossary
.
Chapter 9,
Setting Up OpenLane
for FrameSaver Devices and
Activating SLM Features
Identifies where installation and setup information is
located and how FrameSaver units are supported.
Chapter 10,
Setting Up NetScout
Manager Plus for FrameSaver
Devices
Describes setup of the NetScout Manager Plus
application so it supports FrameSaver units, and so
you can change alarm and history file defaults.
Chapter 11,
Setting Up Network
Health for FrameSaver Devices
Describes setup of Concord’s Network Health
application so reports can be created for FrameSaver
units, and identifies those reports that apply to
FrameSaver units.
Appendix A,
Menu Hierarchy
Contains a graphical representation of how the user
interface screens are organized.
Appendix B,
SNMP MIBs and
Traps, and RMON Alarm Defaults
Identifies the MIBs supported and how they can be
downloaded, describes the unit’s compliance with
SNMP format standards and with its special
operational trap features, and describes the
RMON-specific user history groups, and alarm and
event defaults.
Appendix C,
Router CLI
Commands, Codes, and
Designations
Describes the configuration options available for the
router, and the minimum access level for each
command.
Appendix D,
Router Command
Line Summaries and Shortcuts
Provides a summary of router CLI commands,
showing syntax and defaults.
Appendix E,
Connectors, Cables,
and Pin Assignments
Shows the rear panel, tells what cables are needed,
and provides pin assignments for interfaces and
cables.
Appendix F,
Technical
Specifications
Technical Specifications.
Appendix G,
Equipment List
Equipment List.
Index
Lists key terms, acronyms, concepts, and sections.
Section Description

About This Guide
9128-A2-GB20-80 September 2002 xiii
Product-Related Documents
Complete Paradyne documentation for this product is available at
www.paradyne.com. Select
Library
→
Technical Manuals.
To order a paper copy of this manual:

Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)

Outside the U.S.A., call 1-727-530-8623
Document
Number Document Title
Paradyne FrameSaver Documentation:
9000-A2-GN19
FrameSaver SLV ISDN Installation Instructions
9000-A2-GN1D
9000 Series Access Carrier Installation Instructions
9126-A2-GL10
FrameSaver SLV 9126 and 9126-II Quick Reference
9126-A2-GL12
FrameSaver SLV 9126-II Router Quick Reference
9126-A2-GN10
FrameSaver SLV 9126 1-Slot Unit Installation Instructions
9126-A2-GN11
FrameSaver SLV 9126-II 1-Slot Unit Installation Instructions
9126-A2-GN12
FrameSaver SLV 9126-II Router Installation Instructions
9128-A2-GL10
FrameSaver SLV 9128/9128-II Quick Reference
9128-A2-GN10
FrameSaver SLV 9128 1-Slot Housing-to-9000 Series Access
Carrier Upgrade Instructions
9128-A2-GN11
FrameSaver SLV 9128/9128-II Network Access Module (NAM)
Installation Instructions
9128-A2-GN12
FrameSaver SLV 9128/9128-II 1-Slot Unit Installation Instructions
Paradyne OpenLane NMS Documentation:
7800-A2-GB30
OpenLane SLM Reports Reference Guide
7800-A2-GB32
OpenLane SLM Administrator’s Guide
NetScout Documentation:
2930-170
NetScout Probe User Guide
2930-610
NetScout Manager/Plus User Guide
2930-620
NetScout Manager/Plus & NetScout Server Administrator Guide
2930-788
NetScout Manager Plus Set Up & Installation Guide
Concord Communications Documentation:
09-10010-005
Network Health User Guide
09-10020-005
Network Health Installation Guide
09-10050-002
Network Health –Traffic Accountant Reports Guide
09-10070-001
Network Health Reports Guide

About This Guide
xiv September 2002 9128-A2-GB20-80
Conventions Used
Convention Used When Used
Italic To indicate variable information (for example, DLCI nnnn ,
where
nnnn denotes a 4-digit number) .
Menu sequence: To provide an abbreviated method for indicating the
selections to be made from a menu or selections from within
a menu before performing a procedural step.
For example,
Main Menu
→
Status
→
System and Test Status indicates
that you should select Status from the Main Menu, then
select System and Test Status.
(Path:) To provide a check point that coincides with the menu path
shown at the top of the screen. Always shown within
parentheses so you can verify that you are referencing the
correct table (e.g., Path: main/config/alarm).
Brackets [ ] To indicate multiple selection choices when more than one
selection is available (e.g.,
Performance
Statistics
→
Status
→
[Network/Port-1 ]).
Text highlighted in blue To indicate a hyperlink to additional information when viewing
this manual online. Click on the highlighted text.

9128-A2-GB20-80 September 2002 1-1
1
About the FrameSaver SLV
This chapter includes the following:

System Overview
, below

FrameSaver Diagnostic and SLM Feature Sets
on page 1-4

FrameSaver Diagnostic Feature Set
on page 1-5

FrameSaver SLM Feature Set
on page 1-10

OpenLane SLM System
on page 1-11

NetScout Manager Plus and NetScout Probes
on page 1-12
System Overview
Our system solution consists of:

FrameSaver®SLV (Service Level Verifier) units

OpenLane®SLM (Service Level Management) system

NetScout Manager Plus application

Standalone NetScout Probes, if needed
This solution provides increased manageability, monitoring, and diagnostics so
customers can identify problems more efficiently, troubleshoot those problems
faster, and maximize their network to control costs. It is also compatible with
Concord Communication’s Network Health software.
The FrameSaver SLV 9126-II Router and 9126, 9126-II, and 9128-II CSU/DSUs
operate with other FrameSaver devices, and when teamed with internationally
based FrameSaver devices in multinational applications, provide a complete global
frame relay management solution.

1. About the FrameSaver SLV
1-2 September 2002 9128-A2-GB20-80
CSU/DSU-Specific Features
The following features only apply to the FrameSaver SLV 9126, 9126-II, and
9128-II CSU/DSUs:

Two Interfaces. Provides two interfaces for traffic:
—Synchronous DTE port for user data
—Ethernet Interface for management data

Upstream Pipelining. Provides pipelining capability into the Wide Area
Network (WAN) for reduced latency, where groups of bytes are transmitted as
soon as they are received, rather than waiting for the entire frame to be
collected before sending.

LMI Protocol Support. Automatically detects and initializes the Local
Management Interface (LMI) protocol type on the user data port.
Router-Specific Features
The following features only apply to the FrameSaver SLV 9126-II router:


Device Migration. The FrameSaver SLV 9126-II Router can be converted to a
FrameSaver SLV 9126-II CSU/DSU with a firmware download.

In-Band Router Management. Permits the router to be managed via
customer data PVCs and EDLCIs by assigning an IP address for router
management that is different from the IP address generally used for the
network interface.

Inverse ARP for User Data. Provides Inverse ARP (Address Resolution
Protocol) support for user data, as well as management data. The router
responds to Inverse ARP requests, and can acquire the IP address of a
FrameSaver device at the far end of a customer PVC. ARP information is
retained for both customer data and management data.

1. About the FrameSaver SLV
9128-A2-GB20-80 September 2002 1-3

CLI Access and Configuration. Provides a router Command Line Interface
(CLI), along with the menu-driven user interface, for configuring and managing
the router. It is accessed from the Main Menu via a direct COM port
connection or Telnet.
The following features are configurable using the CLI:
—NAT (Network Address Translation) support provides the means to bind IP
addresses in a private network to addresses in a public, or global, network
for transparent routing between the two domains on all PVCs. Up to 30
NAT pools are supported.
—Routing table configuration permits configuration of static routes. Up to
32 entries can be made.
—IP forwarding to forward multicast IP packets and customer datagrams.
—Filtering on the Ethernet and frame relay interfaces, configurable from the
CLI access list, allows the router to filter MAC frames and prevent
unwanted inbound connections. Two filter access lists are supported per
interface, one for the transmit and one for the receive direction.
The following protocol is supported:
—DHCP (Dynamic Host Configuration Protocol) support for dynamic
allocation of IP addresses and automatic cleanup when a subinterface is
deleted, as well as allowing multiple IP address ranges for DHCP deny
capability. The DHCP server and relay cannot be enabled at the same
time. Up to 253 DHCP clients can be supported. One DHCP pool of
addresses, and one IP address range per pool is supported.

1. About the FrameSaver SLV
1-4 September 2002 9128-A2-GB20-80
FrameSaver Diagnostic and SLM Feature Sets
Depending upon the model ordered, the FrameSaver unit has the basic
FrameSaver frame relay and diagnostic capability, or it is enhanced with additional
SLM (Service Level Management) reporting capability. These are referred to as
feature sets, which provide different levels of intelligence for monitoring, managing,
and reporting performance of the unit.
The two feature sets include:

Basic Diagnostic Feature Set. Models with this feature set provide basic
FrameSaver capabilities, which include:
—Leased Line mode for standard DSU installation and operation
—Device health and status
—Layer 1 (Physical) and Layer 2 (Frame Relay) performance statistics
—Basic physical testing and non-disruptive PVC diagnostics
—A troubleshooting DLCI (Data Link Connection Identifier) for service
provider use and remote management
—Limited RMON (Remote Monitoring) functionality
—Multiplexed management PVCs
See
FrameSaver Diagnostic Feature Set
on page 1-5 for other features and
additional information.

Advanced SLM Feature Set. Models with this feature set provide all the basic
diagnostic capability, plus advanced Service Level Management features.
When additional SLV data is collected and the unit is accessed from an
OpenLane SLM system, Web access to the following information is available:
—TruePut™Technology using Frame and Data Delivery Ratios (FDR and
DDR)
—Web browser access to all diagnostic and reporting functions
—Historical SLA (Service Level Agreement) verification and trend reports
—Real-time RMON (remote monitoring) alarms and configurable alarm
thresholds
—Real-time and historical network performance graphs
—Multiplexed customer PVCs
See
FrameSaver SLM Feature Set
on page 1-10 for more information about
the additional SLM capability.
If the unit does not have the SLM feature set, full SLM capability can be activated
at any time by ordering a Feature Activation Certificate. The OpenLane SLM
system Release 5.3 or above is required to schedule activation of advanced SLM
features in units, and to manage activations.