Paradyne FrameSaver SLV 9664 User manual

FrameSaverSLV 9664
USER’S GUIDE
Document No. 9664-A2-GB20-00
March 2000

A 9664-A2-GB20-00
March 2000
Copyright E2000 Paradyne Corporation.
All rights reserved.
Printed in U.S.A.
Notice
This publication is protected by federal copyright law. No part of this publication may be copied or distributed,
transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form
or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the
express written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.
Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation
reserves the right to revise this publication and to make changes from time to time in the contents hereof without
obligation of Paradyne Corporation to notify any person of such revision or changes.
Changes and enhancements to the product and to the information herein will be documented and issued as a new
release to this manual.
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor directly for any help needed. For
additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor
locations, or Paradyne worldwide office locations, use one of the following methods:
HInternet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at
www.paradyne.com/warranty.)
HTelephone: Call our automated system to receive current information by fax or to speak with a company
representative.
— Within the U.S.A., call 1-800-870-2221
— Outside the U.S.A., call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail them to Technical Publications,
Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to [email protected]. Include
the number and title of this document in your correspondence. Please include your name and phone number if you
are willing to provide additional clarification.
Trademarks
ACCULINK, COMSPHERE, FrameSaver, and Hotwire are registered trademarks of Paradyne Corporation.
NextEDGE, MVL, OpenLane, Performance Wizard, and TruePut are trademarks of Paradyne Corporation. All other
products and services mentioned herein are the trademarks, service marks, registered trademarks, or registered
service marks of their respective owners.
Patent Notification
FrameSaver SLV products are protected by U.S. Patents: 5,550,700 and 5,654,966. Other patents are pending.

i
9664-A2-GB20-00 March 2000
Contents
About This Guide
HPurpose and Intended Audience vii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDocument Organization vii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HProduct-Related Documents ix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HConventions Used x. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 About the FrameSaver SLV 9664
HSLM Overview 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HFrameSaver SLV 9664 Features 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 User Interface and Basic Operation
HLogging On 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HMain Menu 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HScreen Work Areas 2-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HNavigating the Screens 2-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keyboard Keys 2-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function Keys 2-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting from a Menu 2-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching Between Screen Areas 2-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a Field 2-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entering Information 2-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents
ii 9664-A2-GB20-00
March 2000
3 Configuration
HBasic Configuration 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration Option Areas 3-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessing and Displaying Configuration Options 3-5. . . . . . . . . . . . . . . .
Changing Configuration Options 3-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving Configuration Options 3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minimal Configuration Before Deploying Remote Units 3-8. . . . . . . . . . .
HEntering System Information and Setting the System Clock 3-8. . . . . . . . . . .
HSetting Up for Trap Dial-Out 3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Up Call Directories for Trap Dial-Out 3-9. . . . . . . . . . . . . . . . . . . .
HSetting Up Auto-Configuration 3-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a Frame Relay Discovery Mode 3-11. . . . . . . . . . . . . . . . . . . . . .
Automatically Removing a Circuit 3-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HSetting Up Management 3-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Up Local Management at the Central Site 3-14. . . . . . . . . . . . . . . .
Setting Up So the Router Can Receive RIP 3-15. . . . . . . . . . . . . . . . . . . . .
Setting Up Service Provider Connectivity at the Central Site 3-15. . . . . . .
HSetting Up Back-to-Back Operation 3-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Operating Mode 3-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HConfiguration Option Tables 3-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HConfiguring the Overall System 3-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring Frame Relay and LMI for the System 3-18. . . . . . . . . . . . . . . .
Configuring Service Level Verification Options 3-20. . . . . . . . . . . . . . . . . . .
Configuring General System Options 3-22. . . . . . . . . . . . . . . . . . . . . . . . . . .
HConfiguring the Physical Interfaces 3-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the Network Interface 3-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the User Data Port 3-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HConfiguring Frame Relay for an Interface 3-26. . . . . . . . . . . . . . . . . . . . . . . . . .
HManually Configuring DLCI Records 3-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HConfiguring PVC Connections 3-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HSetting Up Management and Communication Options 3-33. . . . . . . . . . . . . . .
Configuring Node IP Information 3-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring Management PVCs 3-36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring General SNMP Management 3-39. . . . . . . . . . . . . . . . . . . . . . .
Configuring Telnet and/or FTP Session Support 3-40. . . . . . . . . . . . . . . . .
Configuring SNMP NMS Security Options 3-43. . . . . . . . . . . . . . . . . . . . . .
Configuring SNMP Traps and Trap Dial-Out 3-44. . . . . . . . . . . . . . . . . . . . .
Configuring the Communication Port 3-49. . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the COM Port to Support an External Modem 3-53. . . . . . . .

Contents
iii
9664-A2-GB20-00 March 2000
4 Security and Logins
HLimiting Access 4-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HControlling Asynchronous Terminal Access 4-2. . . . . . . . . . . . . . . . . . . . . . . . .
HControlling External COM Port Device Access 4-4. . . . . . . . . . . . . . . . . . . . . .
HControlling Telnet or FTP Access 4-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limiting Telnet Access 4-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limiting FTP Access 4-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limiting Telnet or FTP Access Over the TS Management Link 4-7. . . . .
HControlling SNMP Access 4-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disabling SNMP Access 4-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assigning SNMP Community Names and Access Levels 4-9. . . . . . . . .
Limiting SNMP Access Through IP Addresses 4-10. . . . . . . . . . . . . . . . . .
HCreating a Login 4-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HModifying a Login 4-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDeleting a Login 4-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Operation and Maintenance
HDisplaying System Information 5-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HViewing LEDs and Control Leads 5-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LED Descriptions 5-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Lead Descriptions 5-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDevice Messages 5-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HStatus Information 5-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System and Test Status Messages 5-12. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network LMI-Reported DLCIs Status 5-16. . . . . . . . . . . . . . . . . . . . . . . . . . .
PVC Connection Status 5-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Interface Status 5-20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HPerformance Statistics 5-22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clearing Performance Statistics 5-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Level Verification Performance Statistics 5-24. . . . . . . . . . . . . . . .
DLCI Performance Statistics 5-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frame Relay Performance Statistics 5-28. . . . . . . . . . . . . . . . . . . . . . . . . . .
HFTP File Transfers 5-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upgrading System Software 5-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Determining Whether a Download Is Completed 5-34. . . . . . . . . . . . . . . . .
Changing Software 5-34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transferring Collected Data 5-35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents
iv 9664-A2-GB20-00
March 2000
6 Troubleshooting
HProblem Indicators 6-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HResetting the Unit and Restoring Communication 6-3. . . . . . . . . . . . . . . . . . .
Resetting the Unit from the Control Menu 6-3. . . . . . . . . . . . . . . . . . . . . . .
Resetting the Unit By Cycling the Power 6-3. . . . . . . . . . . . . . . . . . . . . . . .
Restoring Communication with a Misconfigured Unit 6-4. . . . . . . . . . . . .
HTroubleshooting Management Link Feature 6-5. . . . . . . . . . . . . . . . . . . . . . . . .
HLMI Packet Capture Utility Feature 6-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing Captured Packets from the Menu-Driven User Interface 6-6. . .
HAlarms 6-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HTroubleshooting Tables 6-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Problems 6-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frame Relay PVC Problems 6-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HTests Available 6-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test Timeout Feature 6-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HStarting and Stopping a Test 6-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aborting All Tests 6-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HPVC Tests 6-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network or Port (Internal) PVC Loopback 6-15. . . . . . . . . . . . . . . . . . . . . .
Send Pattern 6-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitor Pattern 6-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connectivity 6-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HPhysical Tests 6-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTE Loopback 6-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HIP Ping Test 6-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HLamp Test 6-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 Setting Up OpenLane for FrameSaver Devices
HOpenLane Support of FrameSaver Devices 7-1. . . . . . . . . . . . . . . . . . . . . . . .
HSetting Up the OpenLane SLM System 7-2. . . . . . . . . . . . . . . . . . . . . . . . . . . .
HSetting Up FrameSaver SLV Support 7-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents
v
9664-A2-GB20-00 March 2000
8 Setting Up NetScout Manager Plus for FrameSaver Devices
HBefore Getting Started 8-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HConfiguring NetScout Manager Plus 8-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding FrameSaver SLV Units to the NetScout Manager
Plus Network 8-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Verifying Domains and Groups 8-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Correcting Domains and Groups 8-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding SLV Alarms Using a Template 8-8. . . . . . . . . . . . . . . . . . . . . . . . . .
Editing Alarms 8-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding SLV Alarms Manually 8-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating History Files 8-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the User-Defined History Files 8-15. . . . . . . . . . . . . . . . . . . . . . . .
HMonitoring a DLCI’s History Data 8-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HMonitoring the Agent Using NetScout Manager Plus 8-18. . . . . . . . . . . . . . . . .
HStatistical Windows Supported 8-20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 Setting Up Network Health for FrameSaver Devices
HInstallation and Setup of Network Health 9-2. . . . . . . . . . . . . . . . . . . . . . . . . . .
HDiscovering FrameSaver Elements 9-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HConfiguring the Discovered Elements 9-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HGrouping Elements for Reports 9-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HGenerating Reports for a Group 9-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About Service Level Reports 9-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About At-a-Glance Reports 9-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About Trend Reports 9-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printed Reports 9-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HReports Applicable to SLV Devices 9-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A Menu Hierarchy
HMenus A-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents
vi 9664-A2-GB20-00
March 2000
B SNMP MIBs and Traps, and RMON Alarm Defaults
HMIB Support B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDownloading MIBs and SNMP Traps B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HSystem Group (mib-2) B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FrameSaver Unit’s sysDescr (system 1) B-3. . . . . . . . . . . . . . . . . . . . . . . .
FrameSaver Unit’s sysObjectID (system 2) B-3. . . . . . . . . . . . . . . . . . . . .
HInterfaces Group (mib-2) B-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Paradyne Indexes to the Interface Table (ifTable) B-4. . . . . . . . . . . . . . . .
NetScout Indexes to the Interface Table (ifTable) B-5. . . . . . . . . . . . . . . .
HStandards Compliance for SNMP Traps B-6. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trap: warmStart B-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trap: authenticationFailure B-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Traps: linkUp and linkDown B-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Traps: enterprise-Specific B-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Traps: RMON-Specific B-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HRMON Alarm and Event Defaults B-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network ISDN S/T Physical Interface Alarm Defaults B-15. . . . . . . . . . . . .
Frame Relay Link Alarm Defaults B-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DLCI Alarm Defaults – Paradyne Area B-18. . . . . . . . . . . . . . . . . . . . . . . . .
DLCI Alarm Defaults – NetScout Area B-19. . . . . . . . . . . . . . . . . . . . . . . . . .
HObject ID Cross-References (Numeric Order) B-21. . . . . . . . . . . . . . . . . . . . . . .
C Connectors, Cables, and Pin Assignments
HRear Panel C-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HCOM Port Connector C-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COM Port-to-Terminal Cable (Feature No. 3100-F2-540) C-2. . . . . . . . .
LAN Adapter Converter and Cable C-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard EIA-232 Crossover Cable C-4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
HNetwork Connector C-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ISDN Modular Cable C-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HUser Data Port Connector C-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
X.21 DTE Adapter Cable (Feature No. 3100-F1-571) C-8. . . . . . . . . . . . .
V.35 DTE Adapter (Feature No. 3100-F1-570) C-9. . . . . . . . . . . . . . . . . . .
EIA-530 Straight-through Cable (Feature No. 9008-F1-523) C-11. . . . . . .
D Technical Specifications
E Equipment List
HEquipment E-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HCables E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index

vii
9664-A2-GB20-00 March 2000
About This Guide
Purpose and Intended Audience
This document contains information needed to properly set up, configure, and
verify operation of FrameSaver SLV 9664 units with Service Level Verifier (SLV)
functionality designed for ISDN leased line applications. The unit is intended for
use at sites where access is at either 64 kbps or 128 kbps.
This guide is intended for system designers, engineers, administrators, and
operators. You must be familiar with the functional operation of digital data
communications equipment and frame relay networks.
Document Organization
Section Description
Chapter 1 About the FrameSaver SLV 9664. Identifies how the
FrameSaver SLV unit fits into Paradyne’s SLM solution,
and describes the features of the unit.
Chapter 2
User Interface and Basic Operation. Shows how to
navigate the user interface.
Chapter 3
Configuration. Provides configuration information for the
FrameSaver SLV unit.
Chapter 4
Security and Logins. Provides procedures for controlling
access to the FrameSaver SLV and setting up logins.
Chapter 5
Operation and Maintenance. Provides procedures to
display unit identification information and perform file
transfers, as well as how to display and interpret status
and statistical information.
Chapter 6
Troubleshooting. Provides device problem resolution,
alarm, and other information, as well as troubleshooting
and test procedures.

About This Guide
viii 9664-A2-GB20-00
March 2000
Section Description
Chapter 7 Setting Up OpenLane for FrameSaver Devices. Identifies
where installation and setup information is located and how
FrameSaver units are supported.
Chapter 8
Setting Up NetScout Manager Plus for FrameSaver
Devices.
Describes setup of the NetScout Manager Plus
application so it supports FrameSaver units.
Chapter 9
Setting Up Network Health for FrameSaver Devices.
Describes setup of Concord’s Network Health application
so reports can be created for FrameSaver units, and
identifies those reports that apply to FrameSaver units.
Appendix A
Menu Hierarchy . Contains a graphical representation of
how the user interface screens are organized.
Appendix B
SNMP MIBs and Traps, and RMON Alarm Defaults.
Identifies the MIBs supported and how they can be
downloaded, describes the unit’s compliance with SNMP
format standards and with its special operational trap
features, and describes the RMON-specific user history
groups, and alarm and event defaults.
Appendix C
Connectors, Cables, and Pin Assignments. Shows the
rear panel, tells what cables are needed, and provides pin
assignments for interfaces and cables.
Appendix D
Technical Specifications.
Appendix E Equipment List.
Index Lists key terms, acronyms, concepts, and sections.
A master glossary of terms and acronyms used in Paradyne documents is
available on the World Wide Web at www.paradyne.com. Select
Library →
Technical Manuals → Technical Glossary .

About This Guide
ix
9664-A2-GB20-00 March 2000
Product-Related Documents
Document Number Document Title
Paradyne FrameSaver Documentation:
9664-A2-GL10 FrameSaver SLV 9664 Quick Reference
9664-A2-GN10 FrameSaver SLV 9664 Installation Instructions
Paradyne OpenLane NMS Documentation:
7800-A2-GZ41 OpenLane 5.x Service Level Management for UNIX
Quick Start Installation Instructions
7800-A2-GZ42 OpenLane 5.x Service Level Management for
Windows NT Quick Start Installation Instructions
NetScout Documentation:
2930-170 NetScout Probe User Guide
2930-610 NetScout Manager/Plus User Guide
2930-620 NetScout Manager/Plus & NetScout Server
Administrator Guide
2930-788 NetScout Manager Plus Set Up & Installation Guide
Concord Communications Documentation:
09-10010-005 Network Health User Guide
09-10020-005 Network Health Installation Guide
09-10050-002 Network Health – Traffic Accountant Reports Guide
09-10070-001 Network Health Reports Guide
Contact your sales or service representative to order product documentation.
Complete Paradyne documentation for this product is available at
www.paradyne.com. Select
Library → Technical Manuals.
To order a paper copy of this manual:
HWithin the U.S.A., call 1-800-PARADYNE (1-800-727-2396)
HOutside the U.S.A., call 1-727-530-8623

About This Guide
x 9664-A2-GB20-00
March 2000
Conventions Used
Convention Used When Used
Menu selection sequence To provide an abbreviated method for indicating
the selections to be made from a menu or
selections from within a menu before
performing a procedural step.
For example,
Main Menu → Status → System and Test Status
indicates that you should select Status from
the Main Menu, then select System and Test
Status.
(Path:) To provide a check point that coincides with the
menu path shown at the top of the screen.
Always shown within parentheses so you can
verify that you are referencing the correct table
(e.g., Path: main/config/alarm).
Brackets [ ] To indicate multiple selection choices when
multiple options can be displayed (e.g., Clear
[
Network/Port-1 ] Statistics).
Text highlighted in red To indicate a hyperlink to additional information
when viewing this manual online. Click on the
highlighted text.

1-1
9664-A2-GB20-00 March 2000
About the FrameSaver SLV 9664 1
This chapter includes the following:
H SLM Overview
H FrameSaver SLV 9664 Features
SLM Overview
The Service Level Management (SLM) Solution consists of:
HFrameSaverrSLV units
HOpenLanerSLM system
HNetScout Manager Plus application
HStandalone NetScout Probes, if needed
This solution provides increased manageability, monitoring, and diagnostics so
customers can identify problems more efficiently, troubleshoot those problems
faster, and maximize their network to control costs. It is also compatible with
Concord Communication’s Network Health software.
FrameSaver SLV (Service Level Verifier) 9664 units add superior diagnostic
capability, end-to-end visibility, accurate network performance reporting, and SLM
intelligence to frame relay network connections that use dedicated ISDN BRI
(Integrated Services Digital Network Basic Rate Interface) access. FrameSaver
SLV 9664 units are installed between a DTE (e.g., router) and any type of NT1
(Network Termination 1) device providing a standard ISDN S/T interface.

About the FrameSaver SLV 9664
1-2 9664-A2-GB20-00
March 2000
FrameSaver SLV 9664 Features
The FrameSaver SLV unit provides the following features:
HIntelligent Service Level Verification. Provides accurate throughput,
latency, and availability measurements to determine network performance
and whether service level agreements (SLAs) are being met, along with SLA
reporting. SLA parameter thresholds can be configured to provide proactive
notification of a developing network problem.
HSecurity. Provides multiple levels of security to prevent unauthorized access
to the unit.
HTruePuttTechnology. Using Frame Delivery Ratios (FDR) and Data
Delivery Ratios (DDR), throughput (within and above CIR, as well as between
CIR and EIR, and above EIR) can be measured precisely, eliminating
inaccuracies due to averaging. These ratios are available through OpenLane
SLV reports.
HFrame Relay Aware Management. Supports diagnostic and network
management features over the frame relay network using the Annex-A,
Annex-D, and Standard UNI (User Network Interface) LMI management
protocol. The unit’s frame relay capability also supports:
— Inband management channels over the frame relay network using
dedicated PVCs.
— Unique nondisruptive diagnostics.
— CIR monitoring on a PVC basis.
— Multiple PVCs on an interface.
— Multiplexing management PVCs with user data PVCs.
— Multiplexing multiple PVCs going to the same location onto a single
network PVC.
HAuto-Configuration. Provides the following automatic configuration features:
— Frame Relay Discovery – For automatic discovery of network DLCIs and
configuration of a user data port DLCI, the PVC connection, and a
management PVC, which is multiplexed with user data DLCIs.
— LMI Protocol Discovery – For automatic configuration of the protocol
being used by the network.
— DLCI Deletion – For automatic removal of configuration of unused DLCIs
from the unit’s configuration and statistical databases.
— CIR Determination – For automatic recalculation of the committed rate
measurement interval (Tc) and excess burst size (Be) when a DLCI’s CIR
changes.
Excess burst size (Be) and committed burst size (Bc) are recalculated
when Committed Burst Size Bc (Bits) is set to CIR. The committed rate
measurement interval (Tc) is recalculated when Committed Burst Size Bc
(Bits) is set to Other.

About the FrameSaver SLV 9664
1-3
9664-A2-GB20-00 March 2000
HRMON-Based User History Statistics Gathering. Provides everything
needed to monitor network service levels, plus throughput with accurate data
delivery, network latency, and LMI and PVC availability.
In addition, port bursting statistics are kept for all frame relay links. These
statistics are available real-time via the Enterprise MIB and historically as an
RMON2 User History object. In future releases of the OpenLane SLM
system, this will enable even more accurate calculations of utilization.
HNetwork User History Synchronization. Allows correlation of RMON2 User
History statistics among all SLV devices in a network for more accurate
OpenLane SLV reports. Using a central clock, called the network reference
time, all SLV device user history statistics are synchronized across the
network, further enhancing the accuracy of OpenLane SLV reports.
HExtensive Testing Capability. Provides a variety of tests to identify
and diagnose device, network, and other problems. These tests can be
commanded from the unit’s menu-driven user interface or the OpenLane
system (using its easy-to-use Diagnostic Troubleshooting feature).
These tests include V.54 or FT1-ANSI data channel loopback support so the
frame relay network service provider can perform a physical loopback from its
own switch without having to contact the leased line provider for loopback
activation.
HDedicated Troubleshooting PVC. Provides a troubleshooting management
link that helps service providers isolate problems within their network. This
feature can be configured from the menu-driven user interface.
HMaximum Number of PVCs and Management PVCs Supported.
Feature FrameSaver SLV 9664
Through Connections (PVCs) 16
Dedicated Management PVCs 2
HCLLM Protocol Support. Allows passing of CLLM (Consolidated Link Layer
Management) protocol messages so customer premises equipment (e.g., the
router) can cooperate with the network in managing congestion.
HRouter-Independence. Unique diagnostics, performance monitoring,
PVC-based in-band network management, and SNMP connectivity is not
dependent upon external routers, cables, or LAN adapters.
HInverse ARP and Standard RIP Support. Provides Inverse ARP (Address
Resolution Protocol) support so the frame relay router at one end of a
management PVC can acquire the IP address of a FrameSaver unit at the
other end of the PVC. Standard RIP (Routing Information Protocol) allows the
router to automatically learn the routes to all FrameSaver units connected to
that FrameSaver unit.
HLMI Packet Capture. Provides a way to upload data that has been captured
in a trace file so the data can be uploaded and transferred to a Network
Associates Sniffer for analysis, or viewed via the menu-driven user interface.
The 12 most recent LMI messages can be displayed from the menu-driven
user interface.

About the FrameSaver SLV 9664
1-4 9664-A2-GB20-00
March 2000
HATM VPI/VCI and DLCI Correlation. For networks with both ATM and frame
relay-access endpoints, allows the FrameSaver unit to report the originating
Virtual Path or Channel Identifier (VPI/VCI) in the far-end ATM-access
endpoint where the local DLCI is mapped so they can be correlated for
OpenLane SLV reports.
HBack-to-Back Operation. Allows two FrameSaver devices to be connected
via a leased-line network or simulation so a point-to-point configuration can
be implemented. When the unit is operating in this mode, the frame relay
operating rate is configurable and the unit assumes the network side
personality of the UNI.
HConfiguration Upload/Download and Software Download Capability.
Provides quick transfer of configuration options to and from nodes and
software downloads while the unit is running using the standard File Transfer
Protocol (FTP). Two software images can be stored.
HDual Flash Memory. Allows software upgrades while the unit is up and
running. Two software loads can be stored and implemented at the user’s
discretion.
HOpenLane Service Level Management Solution. Provides an
advanced, standards-based performance monitoring and management
application.
Being standards-based, the OpenLane SLM system can also be used with
other management applications like HP OpenView or IBM’s NetView.
OpenLane includes HP OpenView adapters for integrating OpenLane
features with the OpenView Web interface.
Being Web-based, the OpenLane system provides Web access to the data
contained in the database to provide anytime, anywhere access to this
information via a Web browser.
Some of the OpenLane SLM system’s features include:
— Real-time performance graphs provide exact performance measurement
details (not averages, which can skew performance results) of service
level agreement (SLA) parameters.
— Historical SLV graphs provide service level management historical
reports so frame relay SLAs can be verified.
— Diagnostic troubleshooting provides an easy-to-use tool for performing
tests, which include end-to-end, PVC loopback, connectivity, and physical
interface tests.
— Basic configuration allows you to configure FrameSaver devices, and set
RMON alarms and thresholds. Network DLCI Circuit IDs can also be
assigned.
— Automatic SLV device and PVC discovery allows all SLV devices with
their SLV Delivery Ratio configuration option enabled to be discovered
automatically, along with their PVCs.
— A FrameSaver unit can be reset from the OpenLane system.

About the FrameSaver SLV 9664
1-5
9664-A2-GB20-00 March 2000
— Firmware downloading provides an easy-to-use tool for downloading to
an entire network or a portion of the network.
— On-demand polling of FrameSaver devices, and SNMP polling and
reporting are available.
HNetScout Manager Plus and NetScout Probe Support. Provides complete
LAN and WAN traffic analysis and monitoring functions for FrameSaver SLV
devices. The following features are supported using this application:
— Thresholds for RMON 1 (Remote Monitoring, Version 1) alarms and
events can be configured.
— Performance monitoring can be performed using collected RMON 2
(Version 2) data. NetScout Manager Plus’s Protocol Directory and
Distribution functionality allows FrameSaver devices to measure up to
eleven network-layer protocols and report the amount of traffic generated
by each. Its IP Top Talkers and Listeners reporting identifies the devices
using network bandwidth for traffic and protocol analysis, identifying the
network’s top six users. In addition, it collects performance statistics from
FrameSaver devices. Up to 900 samples can be stored in 15-minute
buckets, with 96 buckets in a 24-hour period, for up to five days worth of
data.
— Optional standalone NetScout Probes can be used with FrameSaver
devices at sites where full 7-layer monitoring, an unlimited number of
protocols, and advanced frame capture and decode capabilities are
desired.

About the FrameSaver SLV 9664
1-6 9664-A2-GB20-00
March 2000
This page intentionally left blank.

2-1
9664-A2-GB20-00 March 2000
User Interface and
Basic Operation 2
This chapter tells you how to access, use, and navigate the menu-driven user
interface. It includes the following:
H
Logging On
H Main Menu
H Screen Work Areas
H Navigating the Screens
— Keyboard Keys
— Function Keys
— Selecting from a Menu
— Switching Between Screen Areas
— Selecting a Field
— Entering Information
What appears on the screens depends on:
HCurrent configuration – How your network is currently configured.
HSecurity access level – The security level set by the system administrator
for each user.
HData selection criteria – What you entered in previous screens.

User Interface and Basic Operation
2-2 9664-A2-GB20-00
March 2000
Logging On
Start a session using one of the following methods:
HTelnet session via:
— An in-band management channel through the frame relay network.
— A local in-band management channel configured on the DTE port
between the FrameSaver unit and the router.
HDirect terminal connection over the COM port.
When logging on, the User Interface Idle screen appears.
HIf no security was set up or security was disabled, the Main Menu screen
appears (see page 2-4). You can begin your session.
HIf security was set up and is enabled, you are prompted for a login. Enter
your login ID and password.
When the user interface has been idle, a session is automatically ended and the
screen goes blank when the unit times out. Press Enter to reactivate the
interface.
"Procedure
To log in when security is being enforced:
1. Type your assigned Login ID and press Enter.
2. Type your Password and press Enter.
— Valid characters – All printable ASCII characters
— Number of characters – Up to 10 characters can be entered in the
Login ID and Password fields
— Case-sensitive – Yes
An asterisk (*) appears in the password field for each character entered.
If your login was . . . Then the . . .
Valid Main Menu appears (see page 2-4). Begin your session.
Invalid Message, Invalid Password, appears on line 24, and
the Login screen is redisplayed.
After three unsuccessful attempts:
– A Telnet session is closed.
– The User Interface Idle screen appears for a directly
connected terminal.
– An SNMP trap is generated.
Access is denied.
See your system administrator to verify your login (Login
ID/Password combination).