Paramount Fitness EZ-AC User manual

INSTRUCTIONS
RISK OF PERSONAL INJURY –The EZ-AC is not designed to support the weight
of people or animals, DO NOT place children on the unit or attempt to use
this as a personal support. The EZ-AC is designed for the support of air
conditioner units only!
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY
RESULT IN DEATH, INJURY, OR SIGNIFICANT PROPERTY DAMAGE - For your
protection, read and follow these warnings and instructions carefully before
installing or maintaining this fixture. These instructions do not attempt to
cover all installation and maintenance situations. If you do not understand
these instructions or additional information is required, contact Paramount
Tool at 508-672-0844.
DELIVERY: Upon receipt of fixture and accessories (packed separately),
thoroughly inspect for any freight damage. All damage should be reported to
the delivery carrier. Do not install damaged EZ-AC units. ]
TROUBLESHOOTING CAUTION- If this fixture fails to operate properly, check
to make sure: •All fasteners are tightened sufficiently. • The support foot is
flat against your home •There are no broken or bent portions of the unit.
1. Find a clear area in which you can work.
2. Carefully review instructions prior to assembly.
3. Gather tools required:7/16” open-ended wrench, 7/16” socket
wrench.
4. Place your air conditioner on the floor within your working area
Save these instructions for future reference.

Completed Unit

Parts List
Included hardware- Bolts, Nuts, Washers, Adjustment Knob

Step One- Assembly ‘A’
-Using a wrench and a socket wrench, assemble Part A to
Part B using included 5” hex shoulder bolt, two washers and
a nylon lock-nut as shown above. (the assembly will need to
be adjusted once the entire EZ-AC is assembled.)
Step Two- Assembly B
-Using a wrench and a socket wrench, attach assembly A
(Step one) to Part C using 5” hex bolt, 2 washers and nylon
lock-nut as shown. Insert the plastic knob into assembly B
and screw in until secure.

Step 3- Assembly C
-Using a wrench and a socket wrench, attach part D (Step
one) to Part E using two 5” hex bolts, 2 washers and 2 nylon
lock-nuts as shown.
Step 4- Assembly D- (Consisting of assembly B&C)
-Using a wrench and a socket wrench, attach assembly B
(Step two) to assembly C by using two 5” hex bolts, 2
washers and 2 nylon lock-nuts as shown.

Step 4- Assembly E- Using Window as Gage
Incorrect Placement
Correct Placement
-To assemble the front portion of the EZ-AC you will need to
use the window you plan to install you’re A/C unit as a gage.
-Place parts F and G as shown in the photo above and slide
them away from each other to the base and sides of your
window frame as tight as possible. Using the 1” carriage bolt

place it through any hole out of the way of the center area
as shown in the photo. Remove the unit from the window
and apply a washer and nylon-lock nut to the underside and
tighten with a socket wrench.
Step 5-Assembly F- Consisting of Assembly D&E
-Attach assembly E to the relative center of assembly D
using a washer and nylon-lock nut. Tighten securely using a
socket wrench.

Step 6- Assembly G
-To assemble part H and I to the main assembly (F) you will
need to use your air-conditioner as a gage.
-Place parts H and I on the edges of your air-conditioner as
shown with threaded pem-studs facing up as shown above.
Be sure they are tight against your air-conditioner.
-Place assembly F onto the air-conditioner so that the center
support bracket is aligned with the center of the air-
conditioner as shown above.
-Apply 4 washers and 4 nylon lock-nuts and tighten securely
with a socket wrench.

Step 7- Installing the EZ-AC
-Insert the EZ-AC through the window as shown. Be sure the
EZ-AC is at a slight downwards angle as shown in the
example above.
-If the EZ-AC does not rest at the angle shown above,
remove it from your window- adjust the sliding assembly
(assembly A) and the adjustment knob and retry. Continue
this procedure until the EZ-AC rests firmly in your window
and the support leg (assembly A) is supported by your
home. Be sure the EZ-AC is secure and firm when pressure is
applied to the supporting base.
Incorrect Placement

Step 8- Installing your air conditioner
-Lift your air-conditioner and place onto the EZ-AC be sure
the edges of your air conditioner rest in between the tracks
(parts H and I). Extend the curtains and close your window
onto the EZ-AC.
Congratulations! The EZ-AC assembly and installation is now
complete! When you are ready to remove your air
conditioner simply, remove the EZ-AC afterwards and re-use
year after year no further set-up or adjustment is ever
needed! Be sure to check that all bolts and hex nuts are
secure before re-installing the EZ-AC.

The EZ-AC Assembly and Installation manual is proprietary to
Paramount Tool LLC and no ownership rights are hereby
transferred. No part of the Manual shall be used, reproduced,
translated, converted, adapted, stored in a retrieval system,
communicated or transmitted by any means, for any
commercial purpose, including without limitation, sale, resale,
license, rental or lease, without the prior express written
consent of Paramount Tool LLC.
Paramount Tool LLC does not make any representations,
warranties or guarantees express or implied, as to the
accuracy or completeness of this instruction manual. Users
must be aware that updates and amendments will be made
from time to time to the instruction manual. It is the user's
responsibility to determine whether there have been any such
updates or amendments. Neither Paramount Tool nor any of its
directors, officers, employees or agents shall be liable in
contract, tort or in any other manner whatsoever to any person
for any loss, damage, injury, liability, cost or expense of any
nature, including without limitation incidental, special, direct or
consequential damages arising out of or in connection with the
use of the instruction manual or the installation or assembly of
the EZ-AC.
Questions or Comments?
EZ-AC Group
Paramount Tool LLC
473 Pleasant St.
Fall River, MA
508-672-0844
[e-mail]