Parkside 326566 1901 User manual

CORDLESS DRILL PABS 20-Li D4
CORDLESS DRILL
Translation of the original instructions
AKKU-BOHRSCHRAUBER
Originalbetriebsanleitung
ΕΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟ
ΔΡΑΠΑΝΟΚΑΤΣΑΒΙΔΟ
Μετάφραση των αυθεντικών οδηγιών λειτουργίας
IAN 326566_1901

GB/IE/NI/CY Translation of the original instructions Page 1
GR/CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 13
DE/AT / CH Originalbetriebsanleitung Seite 27
Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the
device.
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τις δυο σελίδες με τις εικόνες και εξοικειωθείτε με όλες τις
λειτουργίες της συσκευής.
Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend
mit allen Funktionen des Gerätes vertraut.

A

BATTERY COMPATIBLE WITH ALL DEVICES OF THE SERIES
„PARKSIDE X 20V TEAM“
20V max.
18V

B C
D E
F G

H I
J K
L

PABS 20-LI D4 GB│IE│NI│CY │ 1 ■
Contents
Introduction......................................................2
Intended use................................................................ 2
Features ................................................................... 2
Package contents ............................................................ 2
Technical details ............................................................. 2
General power tool safety warnings .................................3
1. Work area safety .......................................................... 3
2. Electrical safety ........................................................... 3
3. Personal safety............................................................ 4
4. Power tool use and care .................................................... 4
5. Battery tool use and care.................................................... 5
6. Service .................................................................. 5
Safety guidelines for cordless screw drivers........................................ 5
Safety guidelines for battery chargers ............................................ 6
Before use .......................................................6
Charging the battery pack (see fig. A)............................................ 6
Attaching/disconnecting the battery pack to/from the appliance....................... 6
Checking the battery charge level ............................................... 6
Changing tools.............................................................. 7
Torque selection ring/drill setting ................................................ 7
2 speed gearbox ............................................................ 7
Operation .......................................................7
Switching on and off ......................................................... 7
Adjusting the rotational speed .................................................. 7
Changing the direction of rotation ............................................... 7
Tips and tricks............................................................... 8
Maintenance and cleaning..........................................8
Kompernass Handels GmbH warranty ...............................9
Service .........................................................10
Importer.................................................................. 10
Disposal........................................................10
Translation of the original Conformity Declaration .....................11
Ordering a replacement battery....................................12
Telephone ordering .........................................................12

PABS 20-LI D4
■ 2 │ GB│IE│NI│CY
CORDLESS DRILL PABS 20-Li D4
Introduction
Congratulations on the purchase of your new ap-
pliance. You have selected a high-quality product.
The operating instructions are part of this product.
They contain important information about safety,
usage and disposal. Before using the product, please
familiarise yourself with all operating and safety
instructions. Use the product only as described and
for the range of applications specified. Please also
pass these operating instructions on to any future
owner.
Intended use
This appliance is designed for screwing and drill-
ing into wood, plastic and metal. Use this product
only as described and for the areas of applications
specified. Any other usage of or modification to the
appliance is deemed to be improper and carries a
significant risk of accidents. The manufacturer ac-
cepts no responsibility for damage(s) attributable
to misuse. This appliance is not intended for com-
mercial use.
Features
Gear selector
Bit holder (magnetic)
Rotational direction switch/lock
ON/OFF switch/speed control
Belt clip
Battery charge level button
Battery display LED
Battery pack
Release button for battery pack
LED work light
Chuck
Torque selection ring
High-speed charger
Red charge control LED
Green charge control LED
Package contents
1 cordless drill PABS 20-Li D4
1 high-speed battery charger PLG 20 A1
1 battery pack PAP 20 A1
1 bit PH2 50 mm
1 bit PH1 50 mm
1 carrying case
1 set of operating instructions
Technical details
Cordless drill: PABS 20-Li D4
Rated voltage: 20 V (DC)
Rated idle speed: 1st gear: n00–400 rpm
2nd gear: n00–1400 rpm
Chuck clamping
range : max. Ø 13 mm
Max. drill diameter: Steel: 13 mm
Wood: 30 mm
Battery: PAP 20 A1
Type: LITHIUM ION
Rated voltage: 20 V (DC)
Capacity: 2.0 Ah
Cells 5
High-speed battery charger: PLG 20 A1
INPUT:
Rated voltage: 230–240 V ~, 50 Hz
(AC)
Rated power
consumption: 65 W
Fuse (internal): 3.15 A T3.15A
OUTPUT:
Rated voltage: 21.5 V (DC)
Rated current: 2.4 A
Charging time: approx. 60min.
Protection class: II/ (double insulation)

PABS 20-LI D4 GB│IE│NI│CY │ 3 ■
Noise emission value:
Noise measurement value determined in accord-
ance with EN 62841. The A-rated noise level
of the power tool is typically as follows:
Sound pressure level: LpA = 68.5 dB(A)
Uncertainty K: KpA = 3 dB
Sound power level: LWA = 79.5 dB(A)
Uncertainty K: KWA = 3 dB
Vibration emission value:
Total vibration values (vector total of three directions)
determined in accordance with EN 62841:
Screwing: Vibration emission value
ah: 0.601 m/s2
Uncertainty K = 1.5 m/s2
Drilling in metal: Vibration emission value
ah,D : 1.070 m/s2
Uncertainty K = 1.5 m/s2
NOTE
► The vibration emission values and the noise
emission values given in these instructions
have been measured in accordance with
a standardised test procedure and can be
used for comparison of the power tool with
another tool.
► The specified total vibration values and the
noise emission values can also be used to
make a provisional load estimate.
WARNING!
► Depending on the manner in which the power
tool is being used, and in particular the kind of
workpiece that is being worked, the vibration
and noise emission values can deviate from
the values given in these instructions during
actual use of the power tool.
► Try to keep the load as low as possible.
Measures to reduce the vibration load are,
e.g. wearing gloves and limiting the working
time. Wherein all states of operation must be
included (e.g. times when the power tool is
switched off and times where the power tool is
switched on but running without load).
General power tool
safety warnings
WARNING!
►Read all safety warnings, instructions, il-
lustrations and specifications provided with
this power tool. Failure to follow all instruc-
tions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term „power tool“ in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flam-
mable liquids, gases or dust. Power tools cre-
ate sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or ground-
ed surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.

PABS 20-LI D4
■ 4 │ GB│IE│NI│CY
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising
power tools that have the switch on invites ac-
cidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
h) Do not let familiarity gained from frequent
use of tools allow you to become complacent
and ignore tool safety principles. A careless
action can cause severe injury within a fraction
of a second.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detach-
able, from the power tool before making any
adjustments, changing accessories, or storing
power tools. Such preventive safety measures
reduce the risk of starting the power tool ac-
cidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation. If
damaged, have the power tool repaired be-
fore use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.

PABS 20-LI D4 GB│IE│NI│CY │ 5 ■
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow
for safe handling and control of the tool in unex-
pected situations.
5. Battery tool use and care
a) Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of
fire when used with another battery pack.
b) Use power tools only with specifically desig-
nated battery packs. Use of any other battery
packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from
one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek medi-
cal help. Liquid ejected from the battery may
cause irritation or burns.
e) Do not use a battery pack or tool that is
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
f) Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire
or temperature above 130 °C (265°F) may
cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specified in the instruc-
tions. Charging improperly or at temperatures
outside the specified range may damage the
battery and increase the risk of fire.
CAUTION! RISK OF EXPLOSION!
Never charge non-rechargeable
batteries!
Protect the rechargeable battery from
heat, for example from continuous
exposure to sunlight, fire, water and
moisture. There is a risk of explosion.
6. Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by
the manufacturer or authorized service providers.
Safety guidelines for cordless screw
drivers
WARNING!
■Hold the power tool by insulated gripping
surfaces, when performing an operation
where the fastener may contact hidden wir-
ing. Fasteners contacting a “live” wire may
make exposed metal parts of the power tool
“live” and could give the operator an electric
shock.

PABS 20-LI D4
■ 6 │ GB│IE│NI│CY
Safety guidelines for battery chargers
■ This appliance may be used by chil-
dren aged 8 years and above and
by persons with limited physical,
sensory or mental capabilities or
lack of experience and knowledge,
provided that they are under super-
vision or have been told how to use
the appliance safely and are aware
of the potential risks. Children must
not play with the appliance. Clean-
ing and user maintenance tasks
may not be carried out by children
unless they are supervised.
The charger is suitable for in-
door use only.
WARNING!
■ To avoid potential risks, damaged mains cables
should be replaced by the manufacturer or
the manufacturer’s customer service depart-
ment or a similarly qualified person.
Before use
Charging the battery pack (see fig. A)
CAUTION!
► Always pull out the plug before you remove
the battery pack from or connect the
battery pack to the charger.
■ Never charge the battery pack when the
ambient temperature is below 10°C or above
40°C.
♦ Connect the battery pack to the rapid bat-
tery charger (see Fig. A).
♦ Insert the power plug into the socket. The con-
trol LED lights up red to indicate that the
appliance is charging.
♦ The green control LED indicates that the
charging process is complete and the battery
pack is ready.
♦ Insert the battery pack back into the appli-
ance (see Fig. B).
Attaching/disconnecting the battery
pack to/from the appliance
Inserting the battery pack:
♦ Push the rotation direction switch into the
middle position (lock) (see Fig. C). Allow the bat-
tery pack to click into the handle (see Fig. B).
Removing the battery pack:
♦ Press the release button and remove the bat-
tery pack (see Fig. D).
Checking the battery charge level
♦ Press the battery charge level button to check
the charge level of the battery (see Fig. E). The
status/remaining charge will be shown on the
battery display LED as follows:
♦ GREEN/RED/ORANGE = maximum charge/
performance
RED/ORANGE = medium charge/performance
RED = low charge – charge the battery

PABS 20-LI D4 GB│IE│NI│CY │ 7 ■
Changing tools
Your cordless drill has a fully automatic spindle
lock .
When the motor is stopped, the power train locks
so that the chuck can be opened by turning
it . After you have attached the desired tool
and tightened it by turning the chuck , you can
continue working (see Fig. F). The spindle lock is
automatically released when the motor starts (ON/
OFF switch pressed).
Torque selection ring/drill setting
You can set the torque using the torque selection
ring (see Fig. G).
♦ Select a low level for small screws or soft materials.
♦ Select a high level for large screws, hard materi-
als or removing screws.
♦ Select the drill setting for drilling work by adjust-
ing the torque selection ring to the position
(see Fig. H).
2 speed gearbox
CAUTION!
► Only operate the gear selection switch
when the appliance is at a standstill. Other-
wise the appliance can be damaged.
In first gear (gear selector switch in posi-
tion: 1) (see Fig. I)
you can reach a speed of approx. 400 rpm and a
high torque. This setting is suitable for all screwing
jobs.
In second gear (gear selector switch in
position: 2) (see Fig. J)
you can reach a speed of approx. 1400 rpm for
carrying out drilling work.
Operation
Switching on and off
Switching on:
♦ To start the appliance, press the ON/OFF
switch and keep it pressed in (see Fig. K).
The LED work light lights up when the ON/
OFF switch is depressed lightly or fully. This
allows for illumination of the work area in low
lighting.
Switching off:
♦ Release the appliance's ON/OFF switch to
switch off the appliance.
Adjusting the rotational speed
The ON/OFF switch has a variable speed con-
trol. Pressing the ON/OFF switch lightly yields a
low speed. Increasing pressure increases the speed
(see Fig. K).
NOTE
► The integrated motor brake ensures rapid
stoppage.
Changing the direction of rotation
♦ Change the direction of rotation by pressing the
rotational direction switch towards the left or
right (see Fig. L).

PABS 20-LI D4
■ 8 │ GB│IE│NI│CY
Tips and tricks
Tip! This symbol indicates proper be-
haviour!
♦ Before operation, check whether the screw or
drill bit is correctly positioned, i.e. centred in the
drill chuck.
♦ Screw bits are labelled according to their di-
mensions and their shape. If you are uncertain,
always check whether the bit fits tightly in the
screw head without any free play.
Torque:
♦ Smaller screws/bits can be damaged if you set
the torque or rotational speed too high.
Hard screw joints (in metal):
♦ Particularly high torques occur, for example, in
metal screw joints made using drive sockets.
Select a low rotational speed.
Soft screw joints (e.g. in soft wood):
♦ Again, use a low rotational speed, to avoid e.g.
damaging the surface of the wood upon contact
with the screw head. Use a countersink.
When drilling in wood, metal and other
materials, observe the following:
♦ Use a high speed for drill bits with small diameter
and a low speed for drill bits with large diameter.
♦ Select a low speed for hard materials and a
high speed for soft materials.
♦ Secure or fasten the workpiece in a clamp or
vice (if possible).
♦ Mark the spot where you want to drill using a
centre punch or nail. Select a low rotational
speed when starting.
♦ Pull the rotating drill bit from the hole repeatedly
to remove dust and chips and clear the hole.
Drilling in metal:
♦ Use a metal drill (HSS). For optimum results,
cool the drill bit with cutting oil. Metal drill bits
can also be used to drill into plastics. Start with
a 3 mm diameter drill bit and then increase the
size until the desired hole diameter is achieved.
Drilling in wood:
♦ Use a wood drill with a lathe centre; for deep
holes, use an auger bit; for large-diameter
holes, use a Forstner bit. Small screws can be
screwed directly into soft wood.
Maintenance and cleaning
WARNING! RISK OF INJURY! Always
switch the appliance off and remove
the battery before carrying out any
work on the appliance.
The cordless drill is maintenance-free.
■ The appliance must always be kept clean, dry
and free from oil or grease.
■ Never allow liquids to get into the appliance.
■ Use a soft, dry cloth to clean the housing.
Never use petrol, solvents or cleansers which
can damage plastic.
■ If a lithium-ion battery is to be stored for an
extended period, the charge level should be
checked regularly. The optimum charge level is
between 50% and 80%. The optimum storage
environment is cool and dry.
NOTE
► Replacement parts not listed (such as batter-
ies, switches) can be ordered via our service
hotline.

PABS 20-LI D4 GB│IE│NI│CY │ 9 ■
Kompernass Handels GmbH
warranty
Dear Customer,
This appliance has a 3-year warranty valid from
the date of purchase. If this product has any faults,
you, the buyer, have certain statutory rights. Your
statutory rights are not restricted in any way by the
warranty described below.
Warranty conditions
The warranty period starts on the date of purchase.
Please keep your receipt in a safe place. This will
be required as proof of purchase.
If any material or manufacturing fault occurs within
three years of the date of purchase of the product,
we will either repair or replace the product for you
or refund the purchase price (at our discretion).
This warranty service requires that you present the
defective appliance and the proof of purchase (re-
ceipt) within the three-year warranty period, along
with a brief written description of the fault and of
when it occurred.
If the defect is covered by the warranty, your prod-
uct will either be repaired or replaced by us. The
repair or replacement of a product does not signify
the beginning of a new warranty period.
Warranty period and statutory claims for
defects
The warranty period is not prolonged by repairs
effected under the warranty. This also applies to
replaced and repaired components. Any damage
and defects present at the time of purchase must
be reported immediately after unpacking. Repairs
carried out after expiry of the warranty period shall
be subject to a fee.
Scope of the warranty
This appliance has been manufactured in accord-
ance with strict quality guidelines and inspected
meticulously prior to delivery.
The warranty covers material faults or production
faults. The warranty does not extend to product parts
subject to normal wear and tear or to fragile parts
which could be considered as consumable parts
such as switches, batteries or parts made of glass.
The warranty does not apply if the product has
been damaged, improperly used or improp-
erly maintained. The directions in the operating
instructions for the product regarding proper use
of the product are to be strictly followed. Uses
and actions that are discouraged in the operating
instructions or which are warned against must be
avoided.
This product is intended solely for private use and
not for commercial purposes. The warranty shall
be deemed void in cases of misuse or improper
handling, use of force and modifications/repairs
which have not been carried out by one of our
authorised Service centres.
Warranty claim procedure
To ensure quick processing of your case, please
observe the following instructions:
■ Please have the till receipt and the item number
(e.g. IAN12345) available as proof of pur-
chase.
■ You will find the item number on the type plate
on the product, an engraving on the product,
on the front page of the operating instructions
(below left) or on the sticker on the rear or bot-
tom of the product.
■ If functional or other defects occur, please
contact the service department listed either by
telephone or by e-mail.
■ You can return a defective product to us free of
charge to the service address that will be pro-
vided to you. Ensure that you enclose the proof
of purchase (till receipt) and information about
what the defect is and when it occurred.
You can download these instructions
along with many other manuals,
product videos and installation
software at www.lidl-service.com.
This QR code will take you directly to
the Lidl service page (www.lidl-service.com) where
you can open your operating instructions
by entering the item number (IAN) 123456.

PABS 20-LI D4
■ 10 │ GB│IE│NI│CY
Service
WARNING!
►Have the power tool repaired by the Service
centre or a qualified electrician and only
using genuine replacement parts.This will
ensure that the safety of the appliance is
maintained.
►Always ensure that the power plug or
the mains cable is replaced only by the
manufacturer of the appliance or by an
approved customer service provider.This
will ensure that the safety of the appliance is
maintained.
Service Great Britain
Tel.: [phone]
E-Mail: [email protected]
Service Ireland
Tel.: [phone]
(0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak))
E-Mail: [email protected]
CY Service Cyprus
Tel.: [phone]
E-Mail: [email protected]
IAN 326566_1901
Importer
Please note that the following address is not the
service address. Please use the service address
provided in the operating instructions.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
DE-44867 BOCHUM
GERMANY
www.kompernass.com
Disposal
The packaging is made from environmen-
tally friendly material and can be dis-
posed of at your local recycling plant.
Do not dispose of power tools in
your normal household waste!
European Directive 2012/19/EU requires that
worn-out power tools be collected separately and
recycled in an environmentally compatible manner.
Do not dispose of batteries in your
normal domestic waste!
Defective or worn-out rechargeable batteries must
be recycled according to Directive 2006/66/EC.
Take the battery pack and/or appliance to a
nearby collection facility.
Please consult your local authorities regarding
suitable disposal of worn out power tools/battery
packs.
Dispose of the packaging in an
environmentally friendly manner.
Note the labelling on the packaging
and separate the packaging material
components for disposal if necessary.
The packaging material is labelled
with abbreviations (a) and numbers
(b) with the following meanings:
1–7: Plastics,
20–22: Paper and cardboard,
80–98: Composites
Your local community or municipal
authorities can provide information on
how to dispose of the worn-out
product.

PABS 20-LI D4 GB│IE│NI│CY │ 11 ■
Translation of the original Conformity Declaration
We, KOMPERNASS HANDELS GMBH, documents officer: Mr. Semi Uguzlu, BURGSTR. 21,
DE - 44867 BOCHUM, GERMANY, hereby declare that this product complies with the following
standards, normative documents and EC directives:
Machinery Directive
(2006/42/EC)
EMC (Electromagnetic Compatibility)
(2014/30/EU)
RoHS Directive
(2011/65/EU)*
*The manufacturer bears the full responsibility for compliance with this conformity declaration. The object
of the declaration described above complies with the requirements of the Directive 2011/65/EU of the
European Parliament and Council of 8 June 2011 on the limitations of use of certain dangerous sub-
stances in electrical and electronic appliances.
Applied harmonised standards:
EN 62841-1:2015
EN 62841-2-1:2018
EN 60335-1:2012/A13:2017
EN 60335-2-29:2004/A2:2010
EN 62233:2008
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 50581:2012
Type/appliance designation: Cordless drill PABS 20-Li D4
Year of manufacture: 03-2019
Serial number: IAN 326566
Bochum, 04/03/2019
Semi Uguzlu
- Quality Manager -
Subject to technical changes due to product development.

PABS 20-LI D4
■ 12 │ GB│IE│NI│CY
Ordering a replacement battery
If you want to order a replacement battery for your appliance, you can do so easily via the Internet on
www.kompernass.com or by telephone.
Due to limited stocks, this item may sell out in a relatively short time.
NOTE
► Online ordering of replacement parts is not possible in all countries. In this case, please contact the
Service hotline.
■ The promotion is limited to one battery per customer/appliance and also to a timeline of two months
after the promotion period. Thereafter, the replacement battery can be ordered as a replacement part
under other conditions.
Telephone ordering
Service Great Britain
Tel.: [phone]
E-Mail: [email protected]
Service Ireland
Tel.: [phone]
(0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak))
E-Mail: [email protected]
CY Service Cyprus
Tel.: [phone]
E-Mail: [email protected]
To ensure a fast processing of your order, have the article number of you appliance to hand
(e.g. IAN 326566) in case of questions. The article number can be found on the type plate or the title
page of these instructions.

PABS 20-Li D4 GR│CY │ 13 ■
Περιεχόμενα
Εισαγωγή.......................................................14
Προβλεπόμενη χρήση ....................................................... 14
Εξοπλισμός ...............................................................14
Παραδοτέος εξοπλισμός.....................................................14
Τεχνικά χαρακτηριστικά ...................................................... 14
Γενικές υποδείξεις ασφαλείας για ηλεκτρικά εργαλεία...................15
1. Ασφάλεια στο χώρο εργασίας...............................................16
2. Ηλεκτρική ασφάλεια....................................................... 16
3. Ασφάλεια ατόμων ........................................................16
4. Χρήση και χειρισμός του ηλεκτρικού εργαλείου ................................. 17
5. Χρήση και χειρισμός του επαναφορτιζόμενου εργαλείου ..........................17
6. Σέρβις ................................................................. 18
Υποδείξεις ασφαλείας για δραπανοκατσάβιδα ................................... 18
Υποδείξεις ασφαλείας για φορτιστές............................................ 18
Πριν από τη θέση σε λειτουργία.....................................18
Φόρτιση συστοιχίας συσσωρευτών (βλ. Εικ. Α)....................................18
Τοποθέτηση/Απομάκρυνση συστοιχίας συσσωρευτών στη/από τη συσκευή ............. 18
Έλεγχος κατάστασης συσσωρευτών............................................. 19
Αλλαγή εργαλείων ..........................................................19
Προεπιλογή ροπής στρέψης/Βαθμίδα διάτρησης ................................. 19
Μηχανισμός 2ης ταχύτητας ..................................................19
Θέση σε λειτουργία ...............................................19
Ενεργοποίηση/Απενεργοποίηση...............................................19
Ρύθμιση αριθμού στροφών ...................................................19
Εναλλαγή κατεύθυνσης περιστροφής ...........................................19
Υποδείξεις και τεχνάσματα.................................................... 20
Συντήρηση και καθαρισμός........................................20
Εγγύηση της Kompernass Handels GmbH ............................21
Σέρβις. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Εισαγωγέας .....................................................22
Απόρριψη ......................................................22
Μετάφραση της Πρωτότυπης Δήλωση συμμόρφωσης ...................23
Παραγγελία εφεδρικού συσσωρευτή ................................24
Τηλεφωνική παραγγελία ......................................................24

PABS 20-Li D4
■ 14 │ GR│CY
ΕΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟ
ΔΡΑΠΑΝΟΚΑΤΣΑΒΙΔΟ
PABS 20-Li D4
Εισαγωγή
Σας συγχαίρουμε για την αγορά της νέας σας συ-
σκευής. Αποφασίσατε έτσι για την απόκτηση ενός
προϊόντος υψηλής ποιότητας. Οι οδηγίες χρήσης
είναι τμήμα αυτού του προϊόντος. Περιέχουν σημα-
ντικές υποδείξεις για την ασφάλεια, τη χρήση και
την απόρριψη. Πριν από τη χρήση του προϊόντος,
εξοικειωθείτε με όλες τις υποδείξεις χειρισμού και
ασφάλειας. Χρησιμοποιείτε το προϊόν μόνο όπως
περιγράφεται και για τους αναφερόμενους τομείς
χρήσης. Παραδώστε όλα τα έγγραφα σε περίπτω-
ση παράδοσης του προϊόντος σε τρίτους.
Προβλεπόμενη χρήση
Αυτή η συσκευή προορίζεται για διάτρηση και
βίδωμα σε ξύλο, συνθετική ύλη και μέταλλο. Χρη-
σιμοποιείτε τη συσκευή μόνο όπως περιγράφεται
και για τους αναφερόμενους τομείς χρήσης. Κάθε
άλλη χρήση ή μετατροπή της συσκευής ισχύει ως
μη σύμφωνη με τους κανονισμούς και ενέχει σημα-
ντικούς κινδύνους ατυχημάτων. Για βλάβες από
χρήση μη σύμφωνη με τους κανονισμούς ο κατα-
σκευαστής δεν αναλαμβάνει καμία ευθύνη. Η συ-
σκευή δεν προορίζεται για επαγγελματική χρήση.
Εξοπλισμός
Διακόπτης επιλογής ταχύτητας
Υποδοχή για μύτες (μαγνητική)
Διακόπτης εναλλαγής κατεύθυνσης
περιστροφής/Φραγή
Διακόπτης ON/OFF / Ρύθμιση αριθμού
στροφών
Στήριγμα ζώνης
Πλήκτρο κατάστασης συσσωρευτή
LED ένδειξης συσσωρευτή
Συστοιχία συσσωρευτών
Πλήκτρο για την απασφάλιση της συστοιχίας
συσσωρευτών
LED λυχνίας εργασίας
Τσοκ
Προεπιλογή ροπής στρέψης
Ταχυφορτιστής
Κόκκινο LED ελέγχου φόρτισης
Πράσινο LED ελέγχου φόρτισης
Παραδοτέος εξοπλισμός
1 Επαναφορτιζόμενο δραπανοκατσάβιδο
PABS 20-Li D4
1 Ταχυφορτιστής συσσωρευτή PLG 20 A1
1 Συστοιχία συσσωρευτών PAP 20 A1
1 Μύτη PH2 50 mm
1 Μύτη PH1 50 mm
1 Βαλιτσάκι μεταφοράς
1 Οδηγίες χρήσης
Τεχνικά χαρακτηριστικά
Επαναφορτιζόμενο
δραπανοκατσάβιδο: PABS 20-Li D4
Τάση μέτρησης: 20 V (συνεχές ρεύμα)
Αριθμός στροφών
ρελαντί μέτρησης: 1η ταχύτητα:
n00 - 400 min-1
2η ταχύτητα:
n00 - 1400 min-1
Εύρος σύσφιξης
τσοκ : μέγ. Ø 13 mm
Μέγ. διάμετρος
διάτρησης: χάλυβας: 13 mm
Ξύλο: 30 mm
Συστοιχία συσσωρευτών: PAP 20 A1
Τύπος: ΛΙΘΙΟΥ-ΙΟΝΤΩΝ
Τάση μέτρησης: 20 V (συνεχές ρεύμα)
Απόδοση: 2,0 Ah
Στοιχεία 5
Ταχυφορτιστής συσσωρευτή: PLG 20 A1
ΕΙΣΟΔΟΣ/Input:
Τάση μέτρησης: 230 - 240 V ~, 50 Hz
(Εναλλασσόμενη τάση)
Κατανάλωση μέτρησης: 65 W
Ασφάλεια (εσωτερικά): 3,15 A T3.15A