Patton SmartNode 2290 Series User manual

SmartNode 2290 Series
Leased-Line Extenders over IP
Quick Start Guide
Important —This is a Class A device and is intended for use in a light industrial environment. It is not
intended nor approved for use in an industrial or residential environment.
Part Number: 07M2292-QS, Rev. B
Revised: February 9, 2012
Sales Office: [phone]
Technical Support: [phone]
E-mail: [e-mail]
WWW: www.patton.com

2SmartNode 2290 Series Quick Start Guide
1.0 Installing the SmartNode extender
1.1 Mounting the SmartNode extender
Place the extender on a desktop or similar sturdy, flat surface that offers easy access to the cables. The extender
should be installed in a dry environment with sufficient space to allow air circulation for cooling.
For proper ventilation, leave at least 2 inches (5 cm) to the left, right, front, and rear of the SmartNode
extender.
1.2 Connecting cables
Install the cables in the following order:
1. Installing the RJ-11 voice port cable or cables
(see 1.3 “Installing an interface cable on the extender’s voice ports” on page 3)
• This device contains no user serviceable parts. The equipment shall be
returned to Patton Electronics for repairs, or repaired by qualified
service personnel.
• Mains Voltage: Do not open the case when the power cord is con-
nected. For systems without a power switch, line voltages are
present within the power supply when the power cord is connected.
• The external power adapter shall be a listed Limited Power Source.
Ensure that the power cable used meets all applicable standards for
the country in which it is to be installed, and that it is connected to a
wall outlet which has earth ground. The mains outlet that is utilized
to power the devise shall be within 10 feet (3 meters) of the device,
shall be easily accessible, and protected by a circuit breaker.
• Hazardous network voltages are present in WAN ports regardless of
whether power to the SmartNode is ON or OFF. To avoid electric
shock, use caution when near WAN ports. When detaching cables,
detach the end away from the SmartNode first.
• Do not work on the system or connect or disconnect cables during
periods of lightning activity.
• Before opening the chassis, disconnect the telephone network cables
to avoid contact with telephone line voltages.
• Do not work on the system or connect or disconnect cables during
periods of lightning activity.
• The Interconnecting cables shall be acceptable for external use and
shall be rated for the proper application with respect to voltage, cur-
rent, anticipated temperature, flammability, and mechanical service-
ability.
WARNING
WARNING

SmartNode 2290 Series Quick Start Guide 3
2. Installing the 10/100 Ethernet port cable or cables
(see 1.4 “Installing the Ethernet cable” on page 5)
3. Installing the power input
(see 1.5 “Connecting to external power source” on page 6)
1.3 Installing an interface cable on the extender’s voice ports
The SmartNode extender comes with at least two voice ports (see figure 1) located on the back of the extender.
The voice ports are connected to analog devices via cables (see figure 2 and figure 3) terminated with RJ-11 con-
nectors (see figure 4 and Table 1 on page 4 for pin-out information).
Figure 1. Rear view showing location of Ethernet connectors and voice ports (SmartNode 2294 shown)
Figure 2. FXS connection
, 1.25A Reset
Port
s
ETH 0/1 ETH 0/0
Ethernet connectors Voice ports
RJ-11, male RJ-11, male
, 1.25A Reset
Ports
ETH 0/1 ETH 0/0

4SmartNode 2290 Series Quick Start Guide
Figure 3. FXO connection
Figure 4. RJ-11 pinout diagram
Note Unit must not connect directly to telecom network voltage (TNV).
Table 1. RJ-11 socket
Pin Signal
3Ring(-)
4Tip(+)
RJ-11, male RJ-11, male
PSTN
wall plate
, 1.25A Reset
Ports
ETH 0/1 ETH 0/0
Socket
654321
Plug
123456
Link
100M
Activity
0/00/10/20/3
Enet 0 Ports
Power
Console
Leased-Line Extender Over IP
SmartNode 2294
Run
VoIP Link
Link
100M
Activity
Enet 1

SmartNode 2290 Series Quick Start Guide 5
1.4 Installing the Ethernet cable
The SmartNode 2292 Series has automatic MDX (auto-cross-over) detection and configuration on the Ethernet
ports. Any of the two ports can be connected to a host or hub/switch with a straight-through wired cable (see
figure 5). Ethernet devices (10Base-T or 100Base-T) are connected to the SmartNode’s Ethernet ports (see
table 2 for port pin-out listing) via a cable terminated with RJ-45 plugs. Because the SmartNode 2294 Series
does not have the MDX feature, a cross-over cable is required when connecting SmartNode 2294 Series devices
to a host (see figure 6).
Note Pins not listed are not used.
Figure 5. Connecting a SmartNode 2294 Series device to a hub
Table 2. Ethernet 10/100Base-T (RJ-45) port pin-outs (SmartNode 2294 Series)
Pin Signal
1TX+
2TX-
3RX+
6RX-
Hub
Straight-through cable
RJ-45, male
Tx+
Tx-
Rx+
Rx-
1
2
3
6
RJ-45, male
1 Rx+
2 Rx-
3 Tx+
6 Tx-
, 1.25A Reset
Ports
ETH 0/1 ETH 0/0

6SmartNode 2290 Series Quick Start Guide
Figure 6. Connecting to a host
1.5 Connecting to external power source
The extender comes with an external power supply. This section describes installing the power cord into the
extender. Do the following:
Note Do not connect the power cord to the power outlet at this time.
1. Insert the barrel type connector end of the AC power cord into the external power supply connector.
2. Verify that the AC power cord included with your extender is compatible with local standards. If it is not,
contact Patton to find out how to replace it with a compatible power cord.
3. Connect the male end of the power cord to an appropriate power outlet.
4. Verify that the green Power LED is lit.
2.0 Configuring the SmartNode extender
Patton SmartNodes can be used for a wide variety of IP-based network applications. To support and ease the
configuration of the SmartNodes configuration, templates for the most important applications are available on
the Patton server at www.patton.com/voip.
The main steps for setting up a new SmartNode are shown in figure 7.
The extender power supply automatically adjusts to accept an input voltage from 100
to 240 VAC (50/60 Hz).
Verify that the proper voltage is present before plugging the power cord into the
receptacle. Failure to do so could result in equipment damage.
Host
Cross-over cable
RJ-45, male
Tx+
Tx-
Rx+
Rx-
1
2
3
6
RJ-45, male
1 TX+
2 TX-
3 RX+
6 RX-
Twisted pair 1
Twisted pair 2
, 1.25A Reset
Ports
ETH 0/1 ETH 0/0
CAUTION

SmartNode 2290 Series Quick Start Guide 7
Figure 7. Steps for setting up a new SmartNode
2.1 Configure the IP address
Power connection and default configuration
First the SmartNode must be connected to the mains power supply with the power cable. Wait until the 'Run' LED
stops blinking and lights constantly. Now the SmartNode is ready.
The factory default configuration for the Ethernet interface IP addresses and network masks are listed in table 3.
Both Ethernet interfaces are activated upon power-up.
Table 3. Factory default IP address and network mask configuration
IP Address Network Mask
Interface Ethernet 0 (ETH0) DHCP DHCP
Interface Ethernet 1 (ETH1) 192.168.1.1 255.255.255.0
1
Configure IP address
2
Connect the SmartNode to the network
3
Load configuration
Console port
Serial
interface
PC or workstation
with VT-100
emulation terminal
Ethernet interface
ETH0 PC or workstation
or VT-100 emulation
terminal
2. Modify configuration
Internet
3. Load configuration
1. Download configuration example
Patton Web server
with configuration examples
Note You can manually configure the
SmartNode. You do not have to load a
configuration file.
Link
100M
Activity
0/00/10/20/3
Enet0Ports
Power
Console
Leased-Line Extender Over IP
SmartNode 2294
Run
VoIPLink
Link
100M
Activity
Enet1
Link
100M
Activity
0/00/10/20/3
Enet0Ports
Power
Console
Leased-Line Extender Over IP
SmartNode 2294
Run
VoIPLink
Link
100M
Activity
Enet1
Link
100M
Activity
0/00/10/20/3
Enet0Ports
Power
Console
Leased-Line Extender Over IP
SmartNode 2294
Run
VoIPLink
Link
100M
Activity
Enet1

8SmartNode 2290 Series Quick Start Guide
Connect with the serial interface
The Console port is wired as an EIA-561, RS-232 port. Use the included Model 16F-561 adapter and cable (see
figure 8) between the SmartNode’s Console port and a PC or workstation’s RS-232 serial interface. Activate the
terminal emulation program on the PC or workstation that supports the serial interface (e.g. HyperTerm).
Figure 8. Connecting to the terminal
Terminal emulation program settings:
• 9600 baud
• no parity
• 8 bit
• 1 stop bit
• 1 start bit
• No flow control
Serial Terminal
Note A Patton Model 16F-561 RJ45 to DB-9 adapter is included with
each SmartNode Series device
Link
100M
Activity
0/00/10/20/3
Enet0Ports
Power
Console
Leased-Line Extender Over IP
SmartNode 2294
Run
VoIP Link
Link
100M
Activity
Enet1

SmartNode 2290 Series Quick Start Guide 9
2.2 Login
1. Accessing your SmartNode via the local console port (or via a Telnet session) causes the login screen to
display. Type the factory default login: administrator and leave the password empty. Press the Enter key
after the password prompt.
login:administrator
password: <Enter>
172.16.40.1>
2. After you have successfully logged in you are in the operator execution mode, indicated by > as com-
mand line prompt. With the commands enable and configure you enter the configuration mode.
172.16.40.1>enable
172.16.40.1#configure
172.16.40.1(cfg)#
3. Enter the following commands for the first SmartNode 229x device in the pair:
Copy nvram:a-side-config startup-config
Copy running-config startup-config
4. Follow the same procedure for the other SmartNode 229x device in the pair:
Copy nvram:b-side-config startup-config
Copy running-config startup-config
Note The configuration above is only a sample configuration that you may use as an example. You should
specify your own parameters such as your IP address and other related information as required. For
detailed information on all configuration parameters, refer to the SmartWare Software Configuration
Guide available online at www.patton.com/smartnode.
5. Reboot both units and connect them back-to-back through their Ethernet 0/1 ports. Voice connections will
automatically be set up between the units.
The steps above will configure the IP addresses as well as the required configurations for voice connections.

10 SmartNode 2290 Series Quick Start Guide
3.0 Additional Information
For detailed information about configuring and operating guidance, set up procedures, and troubleshooting,
refer to the SmartNode 2290 Series User Manual available online at www.patton.com/manuals/
SN2290.pdf and the SmartWare Software Configuration Guide available online at www.patton.com/
smartnode.
A.0 Customer and Technical Support
Toll-Free VoIP support: call sip:[e-mail] with a VoIP SIP client
Online support: www.patton.com
E-mail support: suppor[email protected]—answered within 1 business day
Telephone support:
• Standard: [phone] (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to
2200 UTC/GMT)
• Alternate: [phone] (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800
UTC/GMT)
Fax: [phone] (USA) or [phone] (Switzerland)

SmartNode 2290 Series Quick Start Guide 11
B.0 Compliance Information
B.1 Compliance
EMC Compliance:
• EN55022, Class A
• EN55024
Safety Compliance:
• EN60950
B.2 CE Declaration of Conformity
This equipment conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws
of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual recognition
of their conformity.
The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the above
directive is indicated by CE sign on the device.
The signed Declaration of Conformity can be downloaded at www.patton.com/certifications.

12 SmartNode 2290 Series Quick Start Guide
Copyright statement
Copyright © 2012, Patton Electronics Company. All rights reserved.
The information in this document is subject to change without notice. Patton Electronics assumes no
liability for errors that may appear in this document.
Trademarks statement
The term SmartNode is a trademark of Patton Electronics Company. All other trademarks presented in this docu-
ment are the property of their respective owners.
Warranty
For warranty, trademark and compliance information, refer to the SmartNode 2290 Series User Manual located
online at www.patton.com/manuals.
In accordance with the requirements of council directive 2002/96/EC on Waste of
Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate
this product from other waste and scrap and deliver to the WEEE collection system in
your country for recycling.