When using electrical appliances, basic safety precautions
should always be taken including the following:
1.
Read all instructions before using this appliance.
2.
Use fan only for purposes described in the instruction
manual.
3.
To protect against electrical shock do not immerse
unit,plugorcordinwateror spraywithliquidsand
plug the appliance directly into a 120V AC electrical
outlet.
4.
Close supervision is necessary when any appliance is
used by or near children.
5.
Unplug from outlet when not in use, when moving
fan from one location to another, before putting on
or taking off parts and before cleaning.
6.
Avoid contact with moving parts.
7.
Do not operate in the presence of explosive and/or
flammable fumes.
8.
To avoid fire hazard, NEVER place the cord under
rugs or any parts near an open flame, cooking or
other heating appliance.
9.
Do notoperate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
return to an authorized service facility for
examination and/or repair.
10.
Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
tripped over.
11.
The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
12.
Do notletthecordhangovertheedgeof atable,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
13.
Do not use outdoors.
14.
To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
15.
Always use on a dry, level surface.
16.
Do not operate fan until fully assembled with all
parts properly in place.
17.
This product is intended for household use ONLY and
not for commercial or industrial applications.
18.
WARNING: To reduce the riskof electrical shock
andinjury to persons, do notusein window.
19.
WARNING: To reduce the risk of fire or electric
shock, do not use this fan with any solid-state speed
control device.
20.
This product employs overload protection (fuse). A
blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product from
the outlet. Replace the fuse as per the user servicing
instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse
blows, a short circuit may be present and the product
shouldbediscardedor returnedtoanauthorized
service facility for examination and/orrepair.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Your fan comes fully assembled and is ready for use.
OPERATING INSTRUCTIONS
Patton
®
Air Circulators can beusedaloneor in conjunctionwith
anairconditionerunitto circulatealreadycooledairortoforce
it into other rooms. During summer days, the portable Patton
®
AirCirculatorcan beused asa hassock fan to pickup coolair
nearthefloorandcirculateit throughtheentireroom.
1.
To operate fan, turn the speed control knob, located
on the rear grill, to High “3”, Medium “2”, or Low
“1”. To turn the fan off, switch the speed control
knob to Off "
0
" position.
2.
It isnormal for the motor to feel warmto the touch
during operation. The motor is thermally protected
and will automatically shut off should it overheat for
any reason. If this happens, immediately disconnect
the fan from the power outlet.
TILT ADJUSTMENT INSTRUCTIONS
To adjust the angle of the fan simply use both hands to
adjust the fan head to the desired position.
CLEANING/MAINTENANCE INSTRUCTIONS
Follow these instructions to correctly and safely care for
your personal fan. Please remember:
REPLACEABLE FUSE
If your (2.5 Amp, 125 Volt) replaceable fuse blows,
please order a newfuse at1-800-333-1930. Follow the
below instructions to replace the fuse on the plug.
User Servicing Instructions
1.
Unplug your fan. Grasp plug and remove from the
receptacle or other outlet device. Do not unplug by
pulling on cord.
2.
Open fuse cover, located
on the top of the plug, by
using your thumb or a
flathead screwdriver to
slide the cover down
towards the prongs.
NOTE: Ensure that fuse
cover is completely open
before attempting to remove fuse.
3.
Remove fuse carefully by using a small screwdriver
to pry the fuse out of the compartment by the metal
ends of the fuse. (see Figure 1)
4.
Place plug on a solid, flat surface. Insert new 2.5
Amp, 125 Volt fuse into fuse compartment and use a
small screwdriver to secure the metal ends of the
fuse into the compartment. CAUTION: Risk of fire.
Replace fuse only with 2.5 Amp, 125 Volt fuse.
5.
Slide fuse cover closed completely. If fuse cover is
difficultto close,makesurefuseissecuredin place
completely by pressing downon metal ends of the fuse.
6.
Risk of fire. Do not replace attachment plug. Contains
a safety device (fuse) that should not be removed.
Discard product if the attachment plug is damaged.
FAN CLEANING
•
Alwaysunplugthefanbeforecleaningor disassembling.
•
Do notallowwatertodrip on orenterintofanhousing.
•
Be sure to use a soft cloth moistened with a mild
soap solution.
•
Do not use any of the following as a cleaner:
gasoline, thinner, or benzene.
Fan Blade Cleaning Instructions
1.
Unlock the clips around the perimeter of the front
grill and use a Phillips Head screwdriver to remove
the screw at the bottom of the grill.
2.
Remove the front grill.
3.
Clean the fan blade, grill, housing and base with a
soft, damp cloth. DO NOT ATTEMPT TO REMOVE THE
FAN BLADE. Please use caution around the motor
housing area. Do not allow the motor or other
electrical components to be exposed to water.
4.
Replace front grill onto rear grill and secure with the
clips and screw removed in the first step.
FAN STORAGE
When storing your fan in the off season, it is important to
keep it in a safe dry location. It is important to protect
the fan head from dust. We strongly recommend using
the original box from purchase.
