Patton OnSite 2603 User manual

OnSite™ Model 2603 & 2620
WAN Access Router
Quick Start Guide
Important—This is a Class A device and is intended for use in a light
industrial environment. It is not intended nor approved for use in an
industrial or residential environment.
Part Number: 07M2620-QS, Rev. G
Revised: July 25, 2014
Sales Office: [phone]
Technical Support: [phone]
E-mail: [e-mail]
WWW: www.patton.com

2OnSite Model 2603 & 2620 Quick Start Guide
1.0 Power up the router
Your router comes with one of the following power supply options:
•External AC adapter with included power cord
•Internal AC power supply
•Internal DC power supply—no power accessories are included
• This device contains no user serviceable parts. The
equipment shall be returned to Patton Electronics for
repairs, or repaired by qualified service personnel.
• Mains Voltage: Do not open the case the when the
power cord is attached. Line voltages are present
within the power supply when the power cords are con-
nected. The mains outlet that is utilized to power the
devise shall be within 10 feet (3 meters) of the device,
shall be easily accessible, and protected by a circuit
breaker.
• For AC powered units, ensure that the power cable
used meets all applicable standards for the country in
which it is to be installed, and that it is connected to a
wall outlet which has earth ground.
• For units with an external power adapter, the adapter
shall be a listed Limited Power Source.
• Hazardous network voltages are present in WAN ports
regardless of whether power to the unit is ON or OFF.
To avoid electric shock, use caution when near WAN
ports. When detaching the cables, detach the end away
from the device first.
• Do not work on the system or connect or disconnect
cables during periods of lightning activity.
The interconnecting cables shall be acceptable for external
use and shall be rated for the proper application with
respect to voltage, current, anticipated temperature, flam-
mability, and mechanical serviceability.
Use only a 12V certified Limited Power Source external
power adapter marked LPS.
WARNING
CAUTION
CAUTION

OnSite Model 2603 & 2620 Quick Start Guide 3
1.1 Models with external AC adaptor
1. Connect female plug of the AC power cord to the AC adapter provided.
2. Connect the barrel-type connector of the AC adapter to the barrel-type Power jack
on the OnSite router.
3. Insert the male plug of the AC power cord into an AC power outlet (100–240
VAC).
1.2 Models with internal AC power supply
1. Insert the female end of the AC power cord into the internal power supply connec-
tor.
2. Connect the male end of the power cord into an AC power outlet (100–240 VAC).
1.3 Models with internal DC power supply
1. Strip insulation 1/4-inch from the electrical wires that will connect the DC power
source to the OnSite router.
2. Connect the positive (+) terminal from the power source to the positive (+) termi-
nal on the OnSite router.
3. Connect the ground terminal from the power source to the ground terminal (E) on
the OnSite router.
4. Connect the negative (-) terminal from the power source with to the negative (-)
terminal on the OnSite router.
Figure 1. Connecting the DC power supply
Note “+”, “E”, and “-” may be unlabeled.
1.4 Power-up indication
The Power LED blinks as the OnSite router is powering up. When the Power LED stops
blinking and remains lit, the router is ready for you to configure.
2.0 Configure the IP address
The OnSite router is shipped with a factory-configured IP address assigned to the
Ethernet LAN port (green outline). The address is 192.168.200.10/24. In most cases,
you must change the address to be on the same subnet as your PC, as described in the
+E-

4OnSite Model 2603 & 2620 Quick Start Guide
procedures below. If you are not sure which IP address to use for your installation,
contact your network administrator.
2.1 Connecting a PC and logging in
1. Using the included combination RS232/Ethernet cable and DB9-RJ45 adapter,
connect a PC’s serial port to the OnSite router’s Console port (see figure 2).
Figure 2. Connecting OnSite router to the PC’s serial port
2. Start a HyperTerminal session on the PC using the settings:
9600 bps, 8 data bits, 1 stop bit, no parity, no flow control
3. Log in to the OnSite router using the factory-default login and password:
Login: superuser
Password: superuser
Login successful
2.2 Modifying the IP address
1. Display current IP interface settings for the OnSite Ethernet LAN port.
ip list interfaces <enter>
IP Interfaces:
ID | Name | IP Address | DHCP | Transport
---|------|----------------|----------|--------------
1 | ip1 | 192.168.200.10 | disabled | <eth1>
----------------------------------------------------
2. Modify the IP address for the LAN port according to your network requirements.
ip set interface ip1 ipaddress 10.10.10.5 255.255.255.0
Note The above IP address (10.10.10.5/24) is only an example. You must
choose an IP address on the same subnet as your PC.
3. Verify the new address is correct and save it in system boot memory.
ip list interfaces <enter>
system config save <enter>
Link
Frame
TD
RD
Link
100M
Tx
Rx
WANEthernet
Power
Console
ipLinkGateway
High SpeedWANAccess Router
Model 2603
Connect to Console port
Serial port
PC with
terminal emulator

OnSite Model 2603 & 2620 Quick Start Guide 5

Now you can connect the OnSite router to your local IP network and complete the
remaining configuration from your PC using a standard web browser.
3.0 Connect to the local IP network
Connect the OnSite router’s (green) Ethernet port to the same Ethernet segment as your
PC (see figure 3).
Note The Model 2620 does not have an MDI-X switch, so you must use a
cable wired straight-through to connect the Model 2620’s Ethernet port
to the IP network.
If you have a Model 2603, press the MDI-X switch until the Ethernet Link LED turns on.
Figure 3. Connecting the OnSite to the local IP network (Model 2603/K shown)
You can check the network connection with the ping command. For example, you
would ping 10.10.10.5 from your PC.
4.0 Log onto the web management interface
You will now access the web management Graphical User Interface (GUI) to configure
the OnSite using a standard web browser (such as Internet Explorer or Netscape
browser).
1. At your PC, open a web browser and enter the IP address you assigned to the
OnSite router’s Ethernet LAN port in step 2 of section 2.2 “Modifying the IP
address” on page 4.
2. Log in to the web management home page using the username superuser and the
password superuser.
Crossover
10/100
EthernetWAN
Power
MDI-X
RXTX
Connect to
Ethernet port
Ethernet port
MDI-X switch
PC

6OnSite Model 2603 & 2620 Quick Start Guide
Figure 4. OnSite web management home page
3. Now you can use the OnSite router’s web management pages to complete your
configuration (see section 6.0 “Complete the installation” on page 7).
5.0 Connect the WAN port
The OnSite 2603/T, 2603/K, and 2620 come with a T1/E1 WAN interface (presented on
an RJ-48C connector with selectable line impedances of 100-ohms for T1 and 120-
ohms for E1 lines). The Model 2603 has one RJ-48C connector and the 2620 has two.
The Model 2603/K and 2620/KK also come with dual BNC connectors for alternate con-
nection to unbalanced 75-ohm E1 lines.
To connect the WAN port on a Model 2620 or Model 2603/T, or if you plan to use the
RJ-48C port on a 2603/K, refer to section “Connecting to the RJ-48C WAN port”. Oth-
erwise, refer to section “Connecting to the unbalanced 75-ohm TX and RX WAN ports
(Model 2603/K and 2620/KK only)” to install cables onto the BNC connectors on the
2603/K and 2620/KK models.
Connecting to the RJ-48C WAN port
1. Obtain a twisted-pair cable with an RJ-48C plug connector at each end.
2. Plug one end of the cable into the RJ-48C socket (labeled WAN) on the OnSite
Router.
3. Plug the other end of the cable into the T1/E1 device.
4. Repeat steps 1 through 3 to install the remaining WAN cables on a Model 2620
Connecting to the unbalanced 75-ohm TX and RX WAN ports
(Model 2603/K and 2620/KK only)
1. Obtain a coaxial cable with a BNC connector at each end.
2. Plug one end of the cable into the transmit socket (labeled TX) on the OnSite
Router. Plug the other end of the cable into the receive port of the E1 device.

OnSite Model 2603 & 2620 Quick Start Guide 7
3. Plug one end of the cable into the receive socket (labeled RX) on the OnSite
Router. Plug the other end of the cable into the transmit port of the E1 device.
6.0 Complete the installation
To finish configuring your OnSite, and for detailed information about installing, config-
uring, operating, and troubleshooting, refer to the Models 2603, 2621, and 2635 OnSite
Series High Speed Routers User Manual available online at www.patton.com/manuals/
2600SER.pdf.
A.0 Customer and Technical Support
Toll-Free VoIP support: call sip:[email protected] with a VoIP SIP phone
Online support: www.patton.com
E-mail support: [e-mail]—answered within 1 business day
Telephone support:
•Standard: [phone] (USA), Monday–Friday: 8:00 am to 5:00 pm EST
(1300 to
2200 UTC/GMT)
•Alternate: [phone] (Switzerland), Monday–Friday: 8:00 am to 5:00 pm
CET (0900 to 1800 UTC/GMT)
Fax: [phone] (USA) or [phone] (Switzerland)
B.0 Compliance Information
B.1 Compliance
EMC:
•FCC Part 15, Class A
•EN55022, Class A
•EN55024
Safety:
•UL60950-1/CSA C22.2 No. 60950-1
•IEC/EN 60950-1
•AS/NZS 60950-1
PSTN Regulatory:
•These devices are not intended for connection to the PSTN.

8OnSite Model 2603 & 2620 Quick Start Guide
B.2 Radio and TV Interference (FCC Part 15)
This equipment generates and uses radio frequency energy, and if not installed and
used properly—that is, in strict accordance with the manufacturer's instructions—may
cause interference to radio and television reception. This equipment has been tested
and found to comply with the limits for a Class A computing device in accordance with
the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide
reasonable protection from such interference in a commercial installation. However,
there is no guarantee that interference will not occur in a particular installation. If the
equipment causes interference to radio or television reception, which can be deter-
mined by disconnecting the cables, try to correct the interference by one or more of the
following measures: moving the computing equipment away from the receiver, re-ori-
enting the receiving antenna, and/or plugging the receiving equipment into a different
AC outlet (such that the computing equipment and receiver are on different branches).
B.3 CE Declaration of Conformity
Product Description: OnSite 2603, 2620
We certify that the apparatus described above conforms to the requirements of Council
Directive 2004/108/EC on the approximation of the laws of the member states relating
to electromagnetic compatibility; and Council Directive 2006/95/EC on the approxima-
tion of the laws of the member states relating to electrical equipment designed for use
within certain voltage limits.
The safety advice in the documentation accompanying this product shall be obeyed.
The conformity to the above directive is indicated by the CE sign on the device.
The signed Declaration of Conformity can be downloaded from www.patton.com/certi-
fications/.
B.4 Authorized European Representative
D R M Green
European Compliance Services Limited.
Avalon House, Marcham Road
Abingdon,
Oxon OX14 1UD, UK
The safety notices in the documentation accompanying the
products shall be obeyed. The conformity to the above direc-
tive is indicated by the CE sign on the device.

OnSite Model 2603 & 2620 Quick Start Guide 9
Copyright statement
Copyright © 2012, Patton Electronics Company. All rights reserved.
The information in this document is subject to change without notice. Patton Electron-
ics assumes no liability for errors that may appear in this document.
Trademarks statement
The term OnSite is a trademark of Patton Electronics Company. All other trademarks
presented in this document are the property of their respective owners.
Warranty, Trademark, & Compliance Information
For warranty, trademark and compliance information, refer to the Models 2603, 2621,
and 2635 OnSite Series High Speed Routers User Manual available online at www.pat-
ton.com/manuals/2600SER.pdf.
In accordance with the requirements of council directive
2002/96/EC on Waste of Electrical and Electronic Equip-
ment (WEEE), ensure that at end-of-life you separate this
product from other waste and scrap and deliver to the
WEEE collection system in your country for recycling.

10 OnSite Model 2603 & 2620 Quick Start Guide
NOTES
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________