Patton OnSite OS3300 User manual

OnSite™ Model 3300
EFM Router
Quick Start Guide
Important—This is a Class A device and is not intended nor approved
for use in an industrial or residential environment.
Part Number: 07MOS3300-QS, Rev. B
Revised: May 18, 2018
Sales Office: [phone]
Technical Support: [phone]
E-mail: [e-mail]
WWW: www.patton.com

2OnSite OS3300 Quick Start Guide
•Do not open the device when the power cord is connected. For sys-
tems without a power switch and without an external power
adapter, line voltages are present within the device when the power
cord is connected.
•For devices with an external power adapter, the power adapter shall
be a listed Limited Power Source. The mains outlet that is utilized
to power the device shall be within 10 feet (3 meters) of the device,
shall be easily accessible, and protected by a circuit breaker in
compliance with local regulatory requirements.
•For AC powered devices, ensure that the power cable used meets
all applicable standards for the country in which it is to be
installed.
•For AC powered devices which have 3 conductor power plugs (L1,
L2 & GND or Hot, Neutral & Safety/Protective Ground), the wall out-
let (or socket) must have an earth ground.
•For DC powered devices, ensure that the interconnecting cables are
rated for proper voltage, current, anticipated temperature, flamma-
bility, and mechanical serviceability.
•WAN, LAN & PSTN ports (connections) may have hazardous volt-
ages present regardless of whether the device is powered ON or
OFF. PSTN relates to interfaces such as telephone lines, FXS, FXO,
DSL, xDSL, T1, E1, ISDN, Voice, etc. These are known as ?hazard-
ous network voltages? and to avoid electric shock use caution when
workin3g near these ports. When disconnecting cables for these
ports, detach the far end connection first.
•Do not work on the device or connect or disconnect cables during
periods of lightning activity.
This device contains no user serviceable parts. This device can only
be repaired by qualified service personnel.
This device is NOT intended nor approved for connection to the PSTN.
It is intended only for connection to customer premise equipment.
WARNING
WARNING
WARNING

OnSite OS3300 Quick Start Guide 3
1.0 Hardware Installation
1.1 Contents of Package
•OS3300 EFM Router
•External power supply for OnSite Model 3300
•Ethernet cable with RJ45 plugs on each end (included)
1.2 What you will need
•Default unit IP address: 192.168.200.10
•Default username: admin
•Default password: (no password)
•PC Computer
1.3 Identify the connector and attach the cables
All connectors are on the rear panel of the OS3300 Router.
Figure 1. OS3300 EFM Router rear panel connectors
Connect the DSL Interface
To function properly, the OS3300 must be connected using a twisted-pair, uncondi-
tioned, dry, metal wire, between 19 (0.9mm) and 26 AWG (0.4mm). Leased circuits that
run through signal equalization equipment are not acceptable.
The EFM Router is equipped with a RJ-45 interface jack (DSL), which conforms to the
T568B standard. Any standard Category 5e cable can be used to directly connect two
routers. Depending on the router model, it will have a two-wire, four-wire or eight-wire
interface. Observe the signal/pin relationship on the OS3300’s DSL interface jack for
each pair in figure 2 on page 4. Figure 4 on page 4 shows the proper way to wire a
cable with a RJ-45 jack on one end and four RJ-11jacks on the other.

4OnSite OS3300 Quick Start Guide
Figure 2. OS3300 (RJ-45) twisted pair DSL interface
Figure 3. OnSite Pinout for two devices
Figure 4. RJ-45 to RJ-11 cable

OnSite OS3300 Quick Start Guide 5
2.0 Connecting Interfaces
2.1 Connecting Console Interface
Install the supplied RJ-45-to-RJ-45 cable with the DB9-RJ45 adapter between the
OS3300 RS-232 port and an open serial port on your computer. If you need to assem-
ble your own cable, refer to the pinout diagram in figure 5.
Figure 5. DB-9-to-RJ-45 cable diagram
2.2 Connect the Ethernet Interface
The EFM Router has four unshielded RJ-45 auto-MDIX10/100Base-T interfaces. These
are designed to connect directly to a 10/100Base-TX network. Figure 6 shows the sig-
nal/pin relationships on this interface. You may connect this port to a hub or PC using a
straight through or crossover cable that is up to 328 ft long.
Figure 6. OS330010/100Base-T RJ-45 Connector Pinout
2.3 Connect the Power Source
The EFM Router does not have a power switch; it powers on once the device is plugged
in. The power connection is made via the barrel jack on the rear panel of the OS3300.
No configuration is necessary for the power supply.
6 DSR
1 CD
4 DTR
5 SG
2 RD (driven by access server)
3 TD (received by access server)
8 CTS (driven by access server)
7 RTS (received by access server)
1
2
3
4
5
6
7
8
Wired together
(No other electrical
connection)
RJ-45 Jack Signal NameDB-9
1 TX+ (data output)
2 TX- (data output)
3 RX+ (data input)
4 (no connection)
5 (no connection)
6 RX- (data input)
7 (no connection)
8 (no connection)
1
2
3
4
5
6
7
8

6OnSite OS3300 Quick Start Guide
2.4 Router/Bridge Status LEDs
The LEDs indicate the status of power, the WAN (OnSite), and Ethernet connections.
Note When powered down, the LED indicators are clear; when powered on, the LED
indicators are yellow.
Figure 7. OS3300 front panel
3.0 CLI Operation and Configuration
You can connect a PC to configure the OnSite 3300 using the CLI. The 3300 EFM
Router comes equipped with an password protected (easy to use) Command Line
Interface. You can connect directly to the unit and make changes immediately by using
the Console Connection or a SSH connection to the default IP address:
192.168.200.10/24. SSH is enabled by default, Telnet is disabled by default for security
reasons. In this section you can see how easy it is to change IP address, username and
save your configuration. On page 9 you can see a sample configuration for easy con-
nections to Central EFM DSLAM or EFM Peer Router.
3.1 Connect with SSH
1. Connect the Ethernet cable.
2. Connect the power supply.
Table 1. OS3300 front panel LEDs
LED Name LED Function Description
Power ON Indicates power is applied.
ROFF
ON
WAN is configured as CO.
WAN is configured as CPE.
OnSite Pair
(one LED for each
port [1 on OS3301,
2 on OS3302, 4 on
OS3304])
OFF
ON
SLOW BLINK
FAST BLINK
Port is configured as DOWN.
Port is in data mode.
Port is in handshake mode (looking for a CPE
signal).
Port is in training mode (active communica-
tion with CPE).
Ethernet
(0/0 - 0/3)
ON
OFF
Port is linked.
Data is passing over the port.

OnSite OS3300 Quick Start Guide 7
3. Connect via SSH to the extender through CPE or CO IP addresses
— Default CPE IP address: 192.168.200.10
4. Log in with the default username admin and no password.
3.2 Connect with Console
1. Connect the RS232 Console cable. (8-N-1 19200)
2. Connect the power supply.
3. Log in with the default username admin and no password.
3.3 Change the IP address (default: 192.168.200.10)
Follow the command sequence below:
node~>enable
node~#configure
node~(cfg)#context ip ROUTER
node~(ctx-ip)[router]#interface LAN
node~(if-ip)[router.LAN]#no ipaddress 192.168.200.10/24
node~(if-ip)[router.LAN]#ipaddress <new address>/<new
mask>
3.4 Change the default username
The default username will be removed once a new one is created.
Follow the command sequence below:
node~>enable
node~#configure
node~(cfg)#superuser <username> password <password>
3.5 Save the Configuration
Follow the command sequence below:
node~>enable
node~#configure
node~(cfg)#copy running-config startup-config
3.6 OnSite DSL Commands
CO and CPE: This will set the EFM Router as CO or CPE. CO is typically used at the
network, CPE is typically used at the CPE device or CPE network.
node(prt-DSL)# mode {CO|CPE}
Annex Type: Please consult support before changing this setting.
node~(prt-DSL)[<name>]# annex-type { b-g | a-f }

8OnSite OS3300 Quick Start Guide
DSL Rate Configuration: This will increase the DSL rate of the OS3300. Your OnSite
3300 is defaulted to automatically select the optimal rate based on the distance (adaptive).
node(prt-DSL)[0/0]# payload-rate {adaptive [max
<192..15296>] | <192..15296>}
Modulation Scheme: Note higher TC-PAM rates will increase maximum payload rates
available but will decrease distance. Your OnSite 3300 is defaulted to automatically
select the optimal setting. Please consult manual for the rate reach chart to determine
your optimal setting if you choose to hard set this value. Higher TC-PAM rates are ideal
for shorter cable runs offering max symmetrical (upstream/downstream) speeds of
11.4 Mbps (TCPAM64) and 15.3 Mbps (TCPAM128) per pair.
node(prt-DSL)[0/0]# tcpam {auto(16/32) | auto(64/128) | 16
| 32 | 64 | 128}
OnSite Ports: The configurations below are used to configure various aspects of the
OnSite port(s):
node~(prt-DSL)# port dsl 0 0
Signal to Noise Ratio: Configures the acceptable noise margin for adaptive rate. SNR
is the relative strength of the DSL signal to Noise ratio. 6dB is generally the lowest dB
recommended in order for the modem to synch. As overall bandwidth increases, your
signal to noise ratio decreases; the higher the number the better. Your OS3300 is
defaulted at 6 giving you the highest likelihood to connect.
node(prt-DSL)[0/0]# snr-margin <-10..22>
Description: This is the description of the port/DSL (OnSite connection). (Ex: "This
DSL goes to building 4") When entering a description with spaces in the text, the
description must be in quotations.
node~(prt-DSL)[0/0]# description <description>
Use Profile: Configures the acceptable noise margin for adaptive rate. SNR is the rela-
tive strength of the DSL signal to Noise ratio. 6dB is generally the lowest dB recom-
mended in order for the modem to synch.
node~(prt-dsl)[0/0]# use profile <name>
Service Mode: Configures the number of pairs (wires) you want to use. The OS3300
will default to the maximum number of wires available on your version of the OnSite.
OS3301 (2-wire); OS3302 (4-wire); OS3304 (8-wire).
node~(prt-DSL)[0/0]# service-mode { 2-wire | 4-wire | 6-
wire | 8-wire }
Below 6dB bad
6dB-10dB fair
11dB-20dB good

OnSite OS3300 Quick Start Guide 9
Shutdown: Disables or Enables OnSite port(s).
node~(prt-DSL)[0/0]# [no] shutdown
Exit: Return to parent mode.
node~(prt-DSL)[0/0]# exit
Show: Displays all the configured options of the OS3300 OnSite port(s).
node(cfg)# show prt-DSL 0 0
3.7 Sample configuration
Below is a sample setup configuration for a typical CPE EFM Router. This unit is config-
ured as a DHCP Client on the WAN (EFM) side and DHCP Server on the LAN side. It is a
simple connection configured to route all default traffic out the DSL WAN port.
#--------------------------------#
# Sample Configuration #
# Patton Electronics Company #
# OS3304 #
# Release: 3.4.2 2014/03/26 #
# Generated configuration file #
# #
#--------------------------------#
cli version 4.00
no clock CO default-offset
switch mode groups
profile aaa DEFAULT
method 1 CO continue-on-reject
console
use profile aaa DEFAULT
telnet-server
use profile aaa DEFAULT
shutdown
ssh-server
use profile aaa DEFAULT
no shutdown
snmp-server
shutdown
web-server http
use profile aaa DEFAULT
no shutdown
ntp shutdown

10 OnSite OS3300 Quick Start Guide
profile napt CO
profile dhcp-server LAN-POOL
network 192.168.200.0/24
lease 24 hours
default-router 192.168.200.10
domain-name-server 8.8.8.8
domain-name-server 8.8.8.4
include 192.168.200.50
192.168.200.100
profile tls DEFAULT
no authentication incoming
no authentication outgoing
private-key pki:private-key/
DEFAULT
own-certificate 1 pki:own-cer-
tificate/DEFAULT
context ip ROUTER
interface LAN
ipaddress LAN 192.168.200.10/
24
ipaddress DHCP
interface DSL
ipaddress DHCP
use profile napt CO DHCP
routing-table DEFAULT
context ip ROUTER
use profile dhcp-server LAN-POOL
Context IP
An abstract section of the OS300
EFM Router configuration that is
dedicated to the IP and Routing
Layer of Patton Device
profile ppp DEFAULT
context bridge Context Bridge
An abstract section of the OS3300
EFM Router configuration that is
dedicated to the bridging protocol at
the CPU layer of the Patton Device.
bridge-group LAN
no shutdown
bind interface ROUTERLAN
Bridge Group
context switch-group DEFAULT
bind bridge-group LAN
no shutdown
Context Switch Group
An abstract section of the OS3300
EFM Router configuration that is
dedicated to the MAC protocol of the
Hardware and Switching layer of the
Patton Device.