Pearl Eliminator Demon Drive P-3002D Installation guide

Quick Manual: Converting P-3002D to P-3002DL
The Modular Post System installed on Demon Drive Pedals enables you
to convert your P-3002D "right-footed" Double Pedal to a P-3002DL "left-
footed" Double Pedal. Follow the conversion instructions below and also
read the included Instruction Manual to thoroughly understand the
functions of your pedal.
1) Disconnect the Direct Link Connecting Bar from
the Direct Link Connecting Bracket by removing
the Key Bolt using the provided Multi-Function
Drum Key.
SUB PEDAL
Direct Link Connecting Bracket
Key Bolt
Direct Link Connecting Bar
Direct Link Connecting Bracket
Direct Link Connecting Bar

3) Turn the pedal over and remove the four Flat
Head Screws under the Post with the provided
Allen wrench and detach the Post.
2) Loosen the two Allen screws on the Direct Link
Connecting Bracket with the provided Allen
wrench.
Pull the bracket off from the Hexagonal Axle Shaft
as shown.
Loosen the two Allen Screws
Hexagonal Axle Shaft
Direct Link Connecting Bracket
Remove screws here
*Use Allen wrench

4) Reattach the Post to the left side of the pedal.
Rettach the Direct Link Connecting Bracket onto
the Hexagonal Axle Shaft as shown.
*Make sure that the top part of the Bracket is parallel with
the flat end of the Hexagonal Axle Shaft as shown.
*Also make sure that the Bracket is flush with the end of
the Hexagonal Axle Shaft as shown.
Direct Link Connecting Bracket
Hexagonal
Axle Shaft
Post
Flat End of the
Hexagonal Axle Shaft
Hexagonal
Axle Shaft
NOTE
When he pedal is completely assembled, it may be
necessay to move the Bracket slightly to the right or
left to allow maximum freedom of movement of the
Direct Link Connecting Bracket.

6) Unscrew the Key Bolts on both Beater Holder
Links using the provided Multi-Function Drum Key
and remove the Beater Holder Links from the Axle
Shafts.
5) Reconnect the Direct Link Connecting Bracket
to the Direct Link Connecting Bar with the Key
Bolt. Your Sub Pedal is now ready.
MAIN PEDAL
Beater Holder Link

8) Disconnect the Direct Link Connecting Bracket
from Post "B" per the instructions in Step 2.
9) Remove Post "B" and reattach to the left
position as shown.
7) Disconnect the Direct Link Connecting Bar from
the Direct Link Connecting Bracket by removing
the Key Bolt using the provided Multi-Function
Drum Key per instruction in Step 1.
Detach Post "A" per instruction in Step 3.
AB
B
BB
B
Direct Link Connecting
Bracket

10) Reattach the Direct Link Connecting Bracket
to the Axle Shaft of Post "B". Refer to Step 4 for
proper assembly.
Reconnect the Direct Link Connecting Bracket to
the Direct Link Connecting Bar with the Key Bolt.
11) Reattach Post "A" to the right side of the pedal
as shown.
Reattach the two Beater Holder Links onto the
Axle Shafts.
B
Direct Link
Connecting Bracket
Axle Shaft
B
Direct Link
Connecting Bracket
Direct Link
Connecting Bar
A
B
Beater Holder Link

12) Remove the Key Bolt and Nut from the Uni-
Lock Footboard Angle Cam on both posts.
Reinstall them so the head of the Key Bolt is
facing the player as shown.
Connect the Z-Link Drive Shaft and sub pedal to the main
pedal, install the beaters and you're ready to play.
Make sure that the screws are moderately tight and do not
over tighten.
Be careful not to misplace small parts during disassembly and
reassembly.
Remove Key Bolt & Nut
Reinstall Key Bolt & Nut