Peavey Sanctuary SSE 26 User manual

Description
The new SSE enclosure series features high
power ratings with custom components, a
sleek look and a unique, snap-in metal
grille. The SSE 26 is a two-way system
featuring the highly acclaimed Pea ey 14XT
titanium compression dri er with a Sound
Guard IV tweeter protection network and
two maximum-performance 6.5" woofers. It
is rated at 300 Watts program and 600 Watts
peak. This lightweight speaker system is
ideal for smaller enues where space is at a
premium. Connections include a four-pin
Neutrik®Speakon®or a paralleled two-
position terminal block for additional
cabinets. The SSE Series is a ailable in
black, white and natural finishes.
Features
• Two-way sound reinforcement
enclosure
• Designed for permanent installations
• Two premium 6.5" woofers
• Pea ey 14XT™titanium compression
dri er
• Sound Guard™IV tweeter protection
network
• Mounting point for VersaMount™35
bracket
• A ailable in three finishes: black,
white or natural
• 300 Watts program/600 Watts peak
power handling
• 100 Hz to 17 kHz
• 94 dB at 1W/1m
• 8 Ohms
Frequency response, 1 meter on-axis,
swept-sine in anechoic environment:
100 Hz to 17 kHz (±3 dB)
Usable low frequency limit (-10 B
point):
80 Hz to 21 kHz
Power han ling:
Full Range:
300 W program
600 W peak
Soun pressure level, 1 Watt, 1 meter in
anechoic environment:
Full Range:
94.0 dB SPL (2.83 V input)
Maximum soun pressure level (1
meter):
Full Range:
115.8 dB SPL continuous
121.8 dB SPL peak
SPECIFICATIONS
SSE™26

2
Ra iation angle measure at -6 B
point of polar response:
500 Hz to 1.6 kHz:
Horiz. 135° +/- 50°
Vert. 75° +/- 35°
1.6 kHz to 5 kHz:
Horiz. 110° +/- 70°
Vert. 125° +/- 90°
5 kHz to 16 kHz:
Horiz. 80° +/- 20°
Vert. 80° +/- 20°
Directivity factor, Q (Mean):
7.70 +/- 4.99
Directivity in ex, Di (Mean):
7.69 dB +/- 3.49 dB
Trans ucer complement:
Low Frequency Section:
Two 6.5" premium Pea ey woofers+
High frequency section:
Pea ey 14XT™titanium compression dri er
on a 90° x 90° conical Horn
Box tuning frequency:
Low Frequency Section: 100 Hz
Harmonic istortion:
1% rated power
Second Harmonic:
100 Hz: 0.09%
1 kHz: 0.09%
Third Harmonic:
100 Hz: 1.19%
1 kHz: 0.14%
10% rated power
Second Harmonic:
100 Hz: 0.34%
1 kHz: 0.37%
Third Harmonic:
100 Hz: 1.67%
1 kHz: 0.22%
Crossover frequency (internal passive):
Low Frequency - High Frequency:
1.8 kHz
Impe ance (Z):
Full Range:
Nominal: 8.0 Ω
Minimum: 9.1 Ω
Input connections:
One four-pin Neutrik®Speakon®in parallel
with one two-position terminal strip
Enclosure materials & finish:
Trapezoidal, dado-joined 13 mm birch
finished with a textured acrylic
polyurethane, with a full-length metal grille
co ered with acoustical-grade grille cloth.
A ailable in black, white or natural finishes.
Mounting provisions:
(1) Mounting bracket and associated
hardware for attaching to SSE 26. This
bracket will allow for horizontal mounting to
walls and ceilings.
(4) 1/4"-20 threaded mounting points on
back to accommodate use of VersaMount™
35 adjustable mounting bracket
Dimensions (H x W x D):
Front:
23.25" x 9.93" x 9.47"
591 mm x 252 mm x 240 mm
Rear:
23.25" x 5.23" x 9.47"
591 mm x 133 mm x 240 mm
Net weight:
28 lbs. (12.7 kg)
Frequency response
This measurement is useful in determining
how accurately a gi en unit reproduces an
input signal. The frequency response of the
SSE 26 is measured at a distance of 1 meter
using a 1 Watt (into the nominal impedance)
swept-sine input signal. As shown in figure
1, the selected dri ers in the SSE 26 combine
to gi e a smooth frequency response from
100 Hz to 17 kHz.
Directivity
Beamwidth is deri ed from the -6 dB points
from the polar plots (see figure 3), which are
measured in a whole-space anechoic
en ironment. Q and Directi ity Index are
plotted for the on-axis measurement
position. These are specifications pro ide a
reference to the co erage characteristics of
the unit and pro ide insight into proper
placement and installation in the chosen
en ironment. The blending of the
components of the SSE 26 exhibit a
desirable beamwidth and directi ity (figures
3 & 4) suitable for sound reinforcement
applications.
Power han ling
There are many different approaches to
power handling ratings. Pea ey rates this
loudspeaker system's power handling using
a full-range form of the AES Standard 2-
1984. Using audio band 20 Hz to 20 kHz
pink noise with peaks of four times the RMS
le el, this strenuous test signal assures the
user that e ery portion of this system can
withstand today's high technology music.
This rating is contingent upon ha ing a
minimum of 3 dB a ailable amplifier
headroom.
Harmonic istortion
Second and third harmonic distortions s.
frequency are plotted in figures 5 & 6 for two
power le els. Ten percent (10%) of rated
input power and either one percent (1%) of
rated input power or 1 Watt, whiche er is
greater. Distortion is read from the graph as
the difference between the fundamental
signal (frequency response) and the desired
harmonic. As an example, a distortion cur e
that is down 40 dB from the fundamental is
equi alent to 1% distortion.
Mounting
Caution: Before attempting to mount this
speaker, consult a certified structural
engineer. The speaker may fall due to
improper installation, resulting in serious
injury and property damage. DO NOT
suspend or mount any other product or
de ice from this SSE 26 enclosure. The
maximum enclosure angle 45°. Use only
Grade 5 hardware or better. All associated
rigging is the responsibility of others.
Architectural & engineering
specifications
The loudspeaker system shall ha e an
operating bandwidth of 100 Hz to 17 kHz.
The nominal output le el shall be 94.0 dB
when measured at a distance of a meter with
an input of 1 Watt. The nominal impedance
shall be 8.0 ohms. The maximum program
power handling shall be 300 Watts, with a
peak power input of at least 600 Watts and a
minimum amplifier headroom of 3 dB. The
nominal radiation geometry shall be 115
degrees in the horizontal plane and 110
degrees in the ertical plane. The outside
dimensions shall be 23.25 inches high by
9.93 inches wide by 9.47 inches deep. The
weight shall be 28 lbs. The loudspeaker
system shall be a model SSE 26.
3 + 2 YEAR LIMITED WARRANTY
NNOOTTEE:: For details, refer to the warranty
statement. Copies of this statement may
be obtained by contacting Pea ey
Electronics Corporation, P.O. Box 2898,
Meridian, Mississippi 39301-2898.

SPECIFICATIONS
SSE™26
3
20 50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
40
50
60
70
80
90
100
110
dB SPL (re 20 Pa)
Amplitude Response (1W 1m On-Axis)
Figure 1
20 50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
1
10
100 Q & Directivity Index
Q
Figure 4
20
10
Di
0
20 50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
30
40
60
80
100
140
180
300
360
Beamwidth (Degrees)
Beamwidth
Vertical
Horizontal
Figure 3
20 50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
1
2
3
5
10
20
30
50
100 Impedance
Z
()
Figure 2

4
20 50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
40
50
60
70
80
90
100
110
dB SPL (re 20 Pa)
Harmonic Distortion : 1% Rated Power
Figure 6 3rd Harmonic
2nd Harmonic
20 50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
50
60
70
80
90
100
110
120
dB SPL (re 20 Pa)
Harmonic Distortion : 10% Rated Power
Figure 5 3rd Harmonic
2nd Harmonic

SPECIFICATIONS
SSE™26
5
Vertical Polar Patterns 6 dB per Division
0o
30o
60o
90o
-30o
-60o
-90o
50 Hz
0o
30o
60o
90o
-30o
-60o
-90o
80 Hz
0o
30o
60o
90o
-30o
-60o
-90o
125 Hz
0o
30o
60o
90o
-30o
-60o
-90o
200 Hz
0o
30o
60o
90o
-30o
-60o
-90o
315 Hz
0o
30o
60o
90o
-30o
-60o
-90o
250 Hz
0o
30o
60o
90o
-30o
-60o
-90o
400 Hz
0o
30o
60o
90o
-30o
-60o
-90o
630 Hz
0o
30o
60o
90o
-30o
-60o
-90o
500 Hz
0o
30o
60o
90o
-30o
-60o
-90o
63 Hz
0o
30o
60o
90o
-30o
-60o
-90o
100 Hz
0o
30o
60o
90o
-30o
-60o
-90o
160 Hz

Vertical Polar Patterns 6 dB per Division
0o
30o
60o
90o
-30o
-60o
-90o
800 Hz
0o
30o
60o
90o
-30o
-60o
-90o
1.25 kHz
0o
30o
60o
90o
-30o
-60o
-90o
2 kHz
0o
30o
60o
90o
-30o
-60o
-90o
3.15 kHz
0o
30o
60o
90o
-30o
-60o
-90o
5 kHz
0o
30o
60o
90o
-30o
-60o
-90o
4 kHz
0o
30o
60o
90o
-30o
-60o
-90o
6.3 kHz
0o
30o
60o
90o
-30o
-60o
-90o
10 kHz
0o
30o
60o
90o
-30o
-60o
-90o
8 kHz
0o
30o
60o
90o
-30o
-60o
-90o
1 kHz
0o
30o
60o
90o
-30o
-60o
-90o
1.6 kHz
0o
30o
60o
90o
-30o
-60o
-90o
2.5 kHz
6

SPECIFICATIONS
SSE™26
7
Vertical Polar Patterns 6 dB per Division
0o
30o
60o
90o
-30o
-60o
-90o
12.5 kHz
0o
30o
60o
90o
-30o
-60o
-90o
16 kHz

8
Horizontal Polar Patterns 6 dB per Division
-90o
-60o
-30o
0o
30o
60o
90o
50 Hz
-90o
-60o
-30o
0o
30o
60o
90o
80 Hz
-90o
-60o
-30o
0o
30o
60o
90o
125 Hz
-90o
-60o
-30o
0o
30o
60o
90o
200 Hz
-90o
-60o
-30o
0o
30o
60o
90o
315 Hz
-90o
-60o
-30o
0o
30o
60o
90o
250 Hz
-90o
-60o
-30o
0o
30o
60o
90o
400 Hz
-90o
-60o
-30o
0o
30o
60o
90o
630 Hz
-90o
-60o
-30o
0o
30o
60o
90o
500 Hz
-90o
-60o
-30o
0o
30o
60o
90o
63 Hz
-90o
-60o
-30o
0o
30o
60o
90o
100 Hz
-90o
-60o
-30o
0o
30o
60o
90o
160 Hz

SPECIFICATIONS
SSE™26
Horizontal Polar Patterns 6 dB per Division
9
-90o
-60o
-30o
0o
30o
60o
90o
800 Hz
-90o
-60o
-30o
0o
30o
60o
90o
1.25 kHz
-90o
-60o
-30o
0o
30o
60o
90o
2 kHz
-90o
-60o
-30o
0o
30o
60o
90o
3.15 kHz
-90o
-60o
-30o
0o
30o
60o
90o
5 kHz
-90o
-60o
-30o
0o
30o
60o
90o
4 kHz
-90o
-60o
-30o
0o
30o
60o
90o
6.3 kHz
-90o
-60o
-30o
0o
30o
60o
90o
10 kHz
-90o
-60o
-30o
0o
30o
60o
90o
8 kHz
-90o
-60o
-30o
0o
30o
60o
90o
1 kHz
-90o
-60o
-30o
0o
30o
60o
90o
1.6 kHz
-90o
-60o
-30o
0o
30o
60o
90o
2.5 kHz

10
Horizontal Polar Patterns 6 dB per Division
-90o
-60o
-30o
0o
30o
60o
90o
12.5 kHz
-90o
-60o
-30o
0o
30o
60o
90o
16 kHz

SPECIFICATIONS
SSE™26
Input Plate
11

www.sanctuary-series.com
80305314
Features and specifications subject to change without notice.
Pea ey Electronics Corporation 711 A Street Meridian, MS 39301 [phone] FAX [phone] ©2004 Printed in the U.S.A. 3/04