peerAir HDS-WHDI100 User manual

12017-08-21 #:180-9111-3 (2017-10-17)
WIRELESS HD MULTIMEDIA SYSTEM
MODEL: HDS-WHDI100
User Guide
®

22017-08-21 #:180-9111-3 (2017-10-17)
GENERAL SAFETY PRECAUTIONS
RISK OF ELECTRICAL SHOCK
To reduce the risk of electric shock, do not disassemble the unit under any circumstances. No user serviceable
parts inside. All product services should be done by the Peerless-AV certified service personnel.
WARNING
Read before operating equipment
Thank you for purchasing our product. Before using it, please read this user manual carefully and follow the
instructions correctly for safe operation. Please keep this manual handy for future reference. Also, please be sure
to always include this user manual in the packaging when transferring or transporting this product to a different
location.
Batteries Installed Warning
CAUTION - Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type.
The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION:
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do
NOT perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
• Power to the units must be switched off before any work is undertaken, such as anyAV device connection or
TV connection.
• To prevent electric shock, make sure to use the supplied DC adapters as power supply to the Transmitter and
Receiver.
• Be sure the power cord is routed so that it will not be stepped on or pinched by heavy items.
• Avoid overloading electrical outlets or extension cords which otherwise could result in electric shock or fire.
• Disconnect the product from the power source if it is left unattended for an extended period of time, and to
protect the product from lightning.
• To reduce the risk of electric shocks or fire, always disconnect the power cord from the power outlet when you
are not using your device for an extended period of time.
• This product should not be exposed to dripping or splashing liquids. No object filled with liquids, such as
vases, should be placed on the product.
• To avoid electric shock, never stick anything in the slots on the case or remove the cover.
• Place Transmitter and Receiver on a flat, hard and stable surface.
• Do NOT block the ventilation slots on the Transmitter or Receiver or place any heavy object on the top cover.
Blocking the airflow could damage the Transmitter or Receiver. Arrange components so that air can flow
freely around the Transmitter and Receiver. Ensure that there is adequate ventilation if the Transmitter and/
or Receiver is placed in a cabinet. Put the Transmitter and Receiver in a properly ventilated area, away from
direct sunlight or any source of heat.
• To reduce the risk of fire or electric shock, do NOT expose the Transmitter and/or Receiver to water or
moisture.
• This product is intended for indoor use only.

32017-08-21 #:180-9111-3 (2017-10-17)
Symbols
ENG
WARNING
ENG Do not overtighten screws.
ENG
1
2
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
4
+1/2
3
Tools Needed for Assembly.
ENG
ENG - Before installing make sure the supporting surface will support the combined load of the equipment and
hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to
product failure or personal injury. For support please call customer care at 1-800-865-2112.
WARNING

42017-08-21 #:180-9111-3 (2017-10-17)
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter
Radiation Exposure Statement (Transmitter):
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equip-
ment should be installed and operated with minimum distance 20cm between the radiator & your body.
Radiation Exposure Statement (Receiver):
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equip-
ment should be installed and operated with minimum distance 20cm between the radiator & your body
Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation,
all WiFi product marketed in US must fixed to US operation channels only

52017-08-21 #:180-9111-3 (2017-10-17)
Industry Canada Statement
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including in-
terference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:(1) le dispositif ne doit
pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouil-
lage susceptible de provoquer un fonctionnement indésirable.
Caution: (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for
harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be
such that the equipment still complies with the e.i.r.p. limit;
(iii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment
still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and
(iv) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the
bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-
LAN devices.
Avertissement: Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur
les restrictions susmentionnées, notamment:
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à
l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les
mêmes canaux;
(ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5250 à 5350 MHz et de 5470 à 5725
MHz doit être conforme à la limite de la p.i.r.e;
(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 à 5850 MHz) doit être conforme
à la limite de la p.i.r.e. spécifiée pour l'exploitation point à point et l’exploitation non point à point, selon le cas;
(iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont dé-
signés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et
que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits set forth for an un-
controlled environment. This equipment should be installed and operated with minimum distance 20cm between the
radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de ray-
onnement et votre corps.

62017-08-21 #:180-9111-3 (2017-10-17)
Important Information
• The PeerAir™ Wireless HD Multimedia System delivers Full HD 1080p content to your existing HDTV set
wirelessly.
• This system operates in the 5GHz RF band and creates an 802.11n AdHoc network for communication
between transmitter and receiver. With dual external omnidirectional antennas, this system transmits Full HD
1080p content up to 100ft (30m) away line of sight.
• Never use this product in an aircraft or a medical facility as it can cause interference or an undesirable effect.
• The use of this product in the following locations may result in abnormal video and audio output (noise,
blocked image... etc,).
• When the product is placed near a large appliance or metal structure.
• A cluttered room where the wireless signals may be blocked.
• This product has been tested and manufactured to comply with each country’s safety rules. However, there
is no guarantee that interference will not occur in some installations. If interference happens, decrease the
distance between the Transmitter and Receiver.
• This product may interfere with 5GHz wireless devices.
• Optimal use of this product is for in-room/multi-room applications with a range of up to 100 ft. (30m) away line
of sight.
• Any changes or modifications not expressly approved by the manufacturer of this device could void the
product warranty.
• This equipment must be installed and operated in accordance with the provided instructions. The Transmitter
must be installed to provide a separation distance of at least 8” (20cm) from all persons and must not be
operating near or in conjunction with any other Transmitter. End users and installers must be provided with
installation instructions and Transmitter operating conditions for satisfying RF exposure compliance.
• This device should be used only as specified within this manual to meet RF exposure requirements. Use of
this device in a manner inconsistent with this manual could lead to excessive RF exposure conditions.
• CEC/ HDMI Control - The HDS-WHDI100 does not support CEC/HDMI Control. Please ensure that CEC/
HDMI Control is disabled on all connected source equipment and displays. Instructions for this process can be
found in the User Manuals for the connected devices.
Care Of The Unit
To clean, use a soft, dry cloth only. Do not use water or other cleaning products as they may cause electrical failure
or damage the surface of the product.

72017-08-21 #:180-9111-3 (2017-10-17)
Parts List
Description Qty
Atransmitter 1
Breceiver 1
Cantenna 2
Dremote control 1
EDC power adaptor 2
FIR blaster 1
GIR extender 1
B (1)
receiver C (2) antenna
A (1)
transmitter
D (1)
remote control E (2) DC power adaptor
12
HDMI Wireless Extender
G (1)
IR extender
F (1)
IR blaster
IR OUT
IR IN

82017-08-21 #:180-9111-3 (2017-10-17)
AB
CC
2
1
ENG - When installing Peerless media devices directly to gypsum board (drywall), verify that the gypsum board
(drywall) has a minimum depth of 5/16” (8mm).
WARNING
Level. Use dimensions below to
mark mount holes.
ENG
2-1
A,B
2.71"
(69mm)
6.27"
(159mm)
.295"
(7.5mm) .177" (4.5mm)

92017-08-21 #:180-9111-3 (2017-10-17)
2-2
screw
length
Drill mounting holes into supporting surface
(minimum depth = screw length).
ENG
Mounting hardware not
supplied.
ENG
Insert anchor flush to drywall.
ENG
2-3

10 2017-08-21 #:180-9111-3 (2017-10-17)
A,B
2-4
2-5
Install.
ENG
Mounting hardware not
supplied.
ENG
1/6"
(4mm)

11 2017-08-21 #:180-9111-3 (2017-10-17)
12
HDMI Wireless Extender
12
HDMI Wireless Extender
1 2 3
The remote control is powered by one CR2025 battery.
1. To remove the battery cover of the remote control,
pinch then pull out battery cover.
2. Insert new CR2025 battery into the battery module
with positive side facing up.
3. Slide the battery cover back into the remote control.
Incorrect usage of batteries can result in leaks or
bursting. Peerless-AV recommends the following
battery use:
• Remove dead batteries immediately to prevent
battery acid from leaking into the battery
compartment.
• Do not touch exposed battery acid as it may
injure skin.
• Remove the batteries if you do not intend to use
the remote control for a long period of time.
CAUTION
Remote Control Battery Installation And Replacement
Using the Remote Control
Positive side faces up
Power
• Toggles transmitter and receiver to standby
mode
1• Switches input to HDMI 1
2• Switches input to HDMI 2

12 2017-08-21 #:180-9111-3 (2017-10-17)
Transmitter Connection Panel
SOURCE IR21
OUTPUT ONINPUT
DC IN RESET HDMI 2 HDMI 1 HDMI IR OUT OFF
Antenna Jack Antenna Jack Power Switch IR OUT HDMI 1 HDMI 2 HDMI OUT Reset Button DC IN
IR Receiver Eye
Source Button Indicator Lights Indicator Lights
Antenna Jack
• Connects antenna to transmitter
Power Switch
• Toggles power on/off
IR OUT
• Connects IR blaster to the transmitter for
remote control of AV devices that are
connected to the transmitter (e.g. Blu-ray
player, DVD, STB, stc.)
HDMI OUT
• HDMI pass-through output port
HDMI 1
• HDMI 1 input port
HDMI 2
• HDMI 2 input port
Reset Button
• Re-establishes connection with the receiver
DC IN
• 5V DC power input port
IR Receiver Eye
• Accepts commands from Peerless-AV
remote only
Source Button
• Toggles AV device inputs
Indicator Lights
• Indicates power, connection, signal and
source

13 2017-08-21 #:180-9111-3 (2017-10-17)
SOURCE IR21
OUTPUT
DC IN RESET HDMI IR IN
ON
OFF
IR Receiver Eye
Source Button Indicator Lights
Receiver Connection Panel
Antenna Jack
• Connects antenna to receiver
Power Switch
• Toggles power on/off
IR IN
• Allows IR commands to be sent to the
system and source equipment remotely
when IR extender is connected
HDMI OUT
• HDMI output port
Reset Button
• Re-establishes connection with the
transmitter
DC IN
• 5V DC power input port
IR Receiver Eye
• Accepts commands from Peerless-AV
remote only. For control of source
equipment the IR extender must
be connected to the IR in port of the
receiver
Source Button
• Toggles AV device inputs
Indicator Lights
• Indicates power, connection, signal and
source
Antenna Jack Antenna Jack Power Switch IR IN HDMI OUT Reset Button DC IN

14 2017-08-21 #:180-9111-3 (2017-10-17)
Transmitter Setup
Receiver Setup
1. Connect HDMI cable (not included) from source device's HDMI OUT port to Transmitter's HDMI 1 port. Repeat for
HDMI 2 port if a second source device is to be connected.
2. (Optional) If connecting to digital display device using wired connection, plug HDMI cable (not included) from
Transmitter's HDMI OUT port to digital display device's HDMI IN port.
3. Plug DC Power Adapter into power outlet.
1. Connect HDMI cable from Receiver's HDMI OUT port to digital display device's HDMI IN port.
2. Plug DC power adapter into a power outlet.
OUTPUT
DC IN RESET HDMI IR IN
ON
OFF
HDMI IN
HD projector
OUTPUT ONINPUT
DC IN RESET HDMI 2 HDMI 1 HDMI IR OUT OFF
set
top box
blu-ray player
HD projector
digital display
device
HDMI INHDMI OUT
A
E
E
B
digital display
device

15 2017-08-21 #:180-9111-3 (2017-10-17)
OUTPUT ONINPUT
DC IN RESET HDMI 2 HDMI 1 HDMI IR OUT OFF
OUTPUT
DC IN RESET HDMI IR IN
ON
OFF
System Operation
IR Blaster and Extender Setup
Connect the IR Blaster into the IR OUT port of the Transmitter. Place the IR Blaster near the IR window of the
source devices and adhere the IR Blaster in place, so that it does not move.
Connect the IR Extender into the IR IN port of the Receiver. Adhere the IR Extender Eye in a location that is
unobstructed. The IR Extender Eye is where the remote should be aimed for source or system control
When the IR Blaster and IR Extender are connected, source devices can be controlled from Receiver location.
Note: The IR extender supports 20KHz - 60KHz carrier frequencies.
1. Power on the transmitter, receiver and the display that you would like to view content on.
2. During boot-up, the connection indicator light will slowly blink orange until the signal link between the Transmitter
and Receiver is established, between 60 - 70 seconds. Once the transmitter and receiver have established a
connection the orange connection indicator light will begin to blink rapidly.
OUTPUT ONINPUT
DC IN RESET HDMI 2 HDMI 1 HDMI IR OUT OFF
OUTPUT
DC IN RESET HDMI IR IN
ON
OFF
Power On Power On
SOURCE IR21 SOURCE IR21
A
AB
B
AB
FG
12

16 2017-08-21 #:180-9111-3 (2017-10-17)
SOURCE IR21 SOURCE IR21
12
HDMI Wireless Extender
3. Check that your digital display device is turned on and set to the proper HDMI input.
4. Press the desired HDMI input on the remote control, or the SOURCE button on the front of the Transmitter or
Receiver, to select the desired AV source input.
Source Source
OUTPUT
DC IN RESET HDMI IR IN
ON
OFF
Y/Pb/Pr
Video
HDMI
RGB
S-Video
5. Under normal operation the Power indicator light will be illuminated solid blue, the orange connection light will
rapidly blink orange, the signal detection light will illuminate solid green, the selected source indicator light will be
solid blue and the unselected source light will not be illuminated.
System Operation
AB
1212

17 2017-08-21 #:180-9111-3 (2017-10-17)
Troubleshooting
Power indicator
light does not
light up
• Check the power connections on the transmitter and receiver to ensure they are
properly inserted into a functioning power outlet.
• Ensure the power switch is in the ON position.
No video is
displayed on
screen
• Verify that the proper cables have been selected and installed between the Transmitter
input and your source device output.
• On the digital display device's side (connected to the Receiver), select the HDMI port
that the receiver is connected to as the input source.
• Ensure the transmission range between the Transmitter and Receiver is NOT over 100
ft. (30m) line of sight (LOS)
• Move the Transmitter closer to the Receiver.
"Please check
TX input signal"
displayed on
screen
• Ensure your video resolution and frame rate is supported and within the transmission
range.
• Connect the source device to your digital display device to check and modify the video
format compatibility.
• Check that the resolution of your source device is set to 1080p, 1080i, 720p, 576p,
576i, 480p, or 480i. Refer to the Supported Resolution section.
• Ensure the proper cables are connected between the Transmitter and your source
devices.
• Ensure your source devices connected to the Transmitter are powered on.
No signal
displayed on
screen
• Ensure the proper cables are connected between receiver and digital display device.
Poor picture
quality or
intermittent video
• Check that the resolution of your device is set to 1080p, 1080i, 720p, 576p, 576i, 480p,
or 480i. Please refer to the Supported Resolution section.
• Ensure the transmission distance is less than 100 ft. (30m) line of sight (LOS).
No audio • Check your digital display device's volume is properly set and not set to "MUTE" mode.
• Check if your source device’s audio volume has been turned up.
IR Blaster cannot
control AV device • Ensure that the IR extender is plugged into the IR IN port on the Receiver and that the source remote is being aimed at the extender.
• Check the location and position of the IR Blaster on the AV device. Refer to IR Blaster
Setup in the Setup and System Operation section of this manual.

18 2017-08-21 #:180-9111-3 (2017-10-17)
Supported Resolutions
Audio Bit Rate Support
Video Format Timings Resolution Support
Primary CEA Video Timing
720x480i @ 60Hz 480i YES
720x480p @ 60Hz 480p YES
720x576i @ 50Hz 576i YES
720x576p @ 50Hz 576p YES
1280x720p @ 50Hz 720p YES
1280x720p @ 60Hz YES
1920x1080i @ 50Hz 1080i YES
1920x1080p @ 50Hz 1080p YES
1920x1080p @ 60Hz YES
Secondary CEA Video Timing
1920x1080p @ 24Hz
1080P / 24
YES
1920x1080p @ 25Hz YES
1920x1080p @ 30Hz YES
PC Resolutions
800x600p @60Hz 600p YES
1280x720p @60Hz 720p YES
1360x765p @60Hz 765p YES
1024x768p @60Hz
768p
YES
1280x768p @60Hz YES
1366x768p @60Hz YES
1280x800p @60Hz 800p YES
1440x900p @60Hz 900p YES
1280x1024p @60Hz 1024p YES
1440x1050p @60Hz 1050p YES
1680x1050p @60Hz YES
1920x1080p @60Hz 1080p YES
2 Channel PCM 32 - 192 KHz
16 bits YES
24 bits YES
• 2-channel PCM: 16 - 24 bits audio sampling with 32 - 192KHz sampling rate as below:

19 2017-08-21 #:180-9111-3 (2017-10-17)
HDS-WHDI100
Supported Video Resolutions HDMI Input 1080p, 10080i, 720p, 576p, 576i, 480p, 480i
Supported Audio Resolutions Digital Audio LPCM, PCM
Transmission Distance Up to 100 feet line of sight
Antenna 4x omnidirectional (external)
Operating Frequencies 5.745GHz (Channel 149)
Power Supply 100-240V AC in, 5V DC power adaptor
Operating Temperature 32° F - 140° F (0° C - 60° C)
Operating Relative Humidity 10% - 90%
Interface Transmitter Receiver
Dimensions (W x H x D) 6.85" x 1.41" x 5.43" (174 x 36 x 138mm) 6.85" x 1.41" x 5.43" (174 x 36 x 138mm)
Product Specifications
* Transmission distance will depend on actual environment. Distance based on line-of-sight. Structures constructed
of steel, wood, concrete, or/and brick may decrease transmission distance.

The Product is warrantied to be free from defects in material and workmanship, given normal use and care, for 1 Year from the
original purchase date with proof of purchase. Please retain a copy of your receipt as you will need this to obtain warranty work. We
will repair or replace the product which fails as a result of such a defect during the warranty period. The accessories are not covered
by this warranty.
This warranty is the customers’ exclusive remedy for product defect and does not apply to:
• Any modifications made to the product in any way by the consumer
• Attachments to the product by the consumer that causes product damage
• Any product which the seals/and or serial numbers and/or logos have been broken, removed or tampered with, defaced, or
altered in any manner
• Damage caused by abuse, misuse, accident, water, or theft
• Physical damage
• Loss of the Accessories
Except as stated above, Peerless Industries, Inc. makes no express or implied warranties as to any product, in Particular, makes
no warranty of merchantability or fitness for any particular purpose. Peerless Industries, Inc. shall not be liable for consequential or
incidental damages arising from any product defect. Our liability is limited to replacement of any defective product as stipulated under
the warranty conditions. Peerless Industries, Inc. expressly disclaims all warranties not satisfied in this limited warranty. Any implied
warranties that may be imposed by law are limited to the terms of this limited warranty.
ONE YEAR LIMITED WARRANTY
Peerless-AV Europe
Unit 3 Watford Interchange,
Colonial Way, Watford, Herts,
WD24 4WP, United Kingdom
Customer Care
[phone]
www.peerless-av.com
© 2017, Peerless Industries, Inc.
Peerless-AV de Mexico
Ave de las Industrias 413
Parque Industrial Escobedo
Escobedo N.L Mexico 66062
Servicio al Cliente
[phone]
www.peerless-av.com
© 2017, Peerless Industries, Inc.
Peerless-AV
2300 White Oak Circle
Aurora, IL 60502
Ph: [phone]
Fax: [phone]
www.peerless-av.com
© 2017, Peerless Industries, Inc.