PEERLESS DS495 Guide

Model: DS495
3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
Installation and Assembly:
Custom Mac Mini PC Holder
NOTE: Read entire instruction sheet before you start installation and assembly.
• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarnings
containedinthisInstallationSheet.Ifyouhaveanyquestionsregardinganyoftheinstructionsorwarnings,please
callPeerlesscustomercareat1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Makesure that the supporting surface will safely support the combined load of the equipment and all attached hard-
wareand components.
• Neverexceed the Maximum LoadCapacity.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrews firmly,butdo not overtighten. Overtightening can damagetheitems, greatly reducing their holding
power.
WARNING
Maximum Load Capacity: 10 lb (4.5 kg)

2 of 5 ISSUED:03-05-09 SHEET#:125-9053-1
Before you begin, make sure all parts shown are included with your product.
Parts may appear slightly different than illustrated. A
C
BE
Parts may appear slightly different than illustrated.
D
Description Qty. Part #
Acomputer box 1 124-1139
Balternate support bracket 4 124-1141
Cbox cover 1 124-1140
D#10 x 1/2" TEK phillips screw 4 520-1320
EM4 x 10 mm serrated washer head socket pin screw 2 510-1060
F4mm security allen wrench 1 560-9646
Gcable tie 6 560-9711
HM5 x 10 mm type-F socket pin screw 8 520-1164
Parts List
FGH

3 of 5 ISSUED:03-05-09 SHEET #:125-9053-1
• Installermust verify that the supporting surface will safely support the combinedweightof all attached equipment and
hardware.
Hold back of computer box (A) against the back of PLCM-2 (not included). Line up locator hole of computer box (A)
with screw of PLCM-2 so that the head of screw is visible, as shown in fig. 1.1. Secure with four #10 x 1/2" TEK
phillips screws (D) as shown in fig. 1.2.
Skip to step 2.
1
DA
PLCM-2
(NOTINCLUDED)
A
fig. 1.1
fig. 1.2
PLCM-2
(NOTINCLUDED)
SCREW
LOCATER
HOLE
WARNING
Installation to PLCM-2 (Not Included)
EXTENSIONCOLUMN
(NOTINCLUDED)

4 of 5 ISSUED:03-05-09 SHEET #:125-9053-1
There are eight mounting places for the alternate support brackets (B) as shown in fig. 1.3. Determined the locations
foralternate support brackets (B) according to supporting surface. Using allen wrench (F), fasten two or four alternate
support brackets (B) to computer box (A) with two M5 x 10 mm type-F socket pin screws (H) for each alternate
support bracket (B). Use installer supplied screws/fasteners to attach alternate support brackets (B) to supporting
surface.
NOTE: For each alternate support brackets (B), two screws must be used for attachment to supporting surface.
1
Installation to Supporting Surface
fig. 1.3
• Installermust verify that the supporting surface will safely support the combinedweightof all attached equipment and
hardware.
WARNING
fig. 1.4
A
B
H
B
A

5 of 5 ISSUED:03-05-09 SHEET #:125-9053-1
Attach power supply and mini mac to computer box (A) using cable ties (G).
2
A
3Slide tabs of box cover (C) into slots of computer box (A). Using allen wrench (F), secure box cover (C) with two
M4 x 10 mm serrated washer head socket pin screws (E).
NOTE: Boxcover(C) can be oriented left or right.
E
A
C
G
POWER
SUPPLY
MINIMAC
©2007,PeerlessIndustries,Inc.Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.