PEERLESS Solid-Point PLCM 1 CP Guide

ISSUED:08-21-02 SHEET #: 200-9405-9 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
1 of 6
Read instruction sheet before you start installation and assembly.
Model:PLCM 1 CP,
PLCM UNL CP
Maximum Load Capacity:
225 lb (102.3 kg)
Installation and Assembly -Solid•Point™Flat Panel Straight
Column Ceiling Mount
R
This product is intended for use with UL
Listed products and must be installed by a
qualified professional installer.
TABLE OF CONTENTS
Installations
InstallingFlatPanelStraightColumnCeilingMount toceiling
pages 3-4
Applications
Installationofplasma screensand
30" or larger LCD screens ...........................................page 5
Installationof smallLCDscreens .................................page 6
• Installer must verify that the ceiling will safely support
thecombined weightofallattachedequipment and
hardware.
WARNING

ISSUED:08-21-02 SHEET #: 200-9405-9 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
2 of 6
D
F
A
Note: Some parts may not appear exactly as illustrated.
HI
C
E
G
J
Fasteners
B
K
L
M
PLCM 1 CP
PLCM UNL CP
Description Qty Part #
Aceiling arm box 1 201-1062
Btilt bracket 1 200-1552
C33" extension column 1 139-1088
Dretaining collar 1 1800-375
EM5 x .8 x 10 mm penta-pin™ screw 5 505-9010
F2.875 OD x 2.125 ID x .062 H fiber washer 1 540-9432
GM10 x 1.5 x 15 mm penta-pin screw 8 520-9263
HM10 x 2" penta-pin tool 1 520-9260
IM5 x 1" penta-pin tool 1 520-9249
JM5 x .8 x 8 mm phillips Type F screw 4 520-1167
Kceiling plate 1 128-1039
Lceiling plate end cap 2 2PT-22CA01D
M#14 x 2.5" hex head phillips wood screw 4 5S1-015-C03
Before you begin, make sure all parts shown are included with your product.
PARTS LIST

ISSUED:08-21-02 SHEET #: 200-9405-9 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
3 of 6
L
K
For Wood Joist Finished Ceiling, Exposed
Wood Joists, or Wood Beam Ceiling. Drill four
5/32" (4 mm) dia. holes to a minimum depth of
2.5"(64mm) INTOJOIST CENTERS. Attach
ceiling plate (K) with four #14 x 2.5" (6 mm x 65
mm) wood screws (M) using a 3/8"(10 mm) socket
wrench.Tighten woodscrews (M)soceiling plate
is firmly attached. Snap end caps (L) into place.
For Concrete Ceilings drillfour 5/16"(8 mm)
dia. holes to a minimum depth of 1 3/4" (45
mm). Attach ceiling plate (K) using concrete
expansionanchorsas shownin 1-1and 1-2.
Then snap end caps (L) into place.
Align hole in ceiling plate with hole in ceiling.
Gentlyhammerinconcreteanchor.
Use a 10 mm wrench to tighten concrete
anchor to 80 in • lb (9 N.M.) maximum torque
toexpand anchors.
FORPRODUCT SAFETYUSE ONLYRAWL™
#5005OR HILTI™HL814CONCRETE
ANCHORS.Order accessorykit #ACC 210
which contains four .312 x 1.625
(8 mm x 41 mm) concrete expansion
anchors.
L
K
M
CONCRETE
PLASTER/
DRYWALL
ACC210
• Tighten wood screws so that ceiling plate is firmly
attached,but donot overtighten.Overtightening can
damagescrews, greatlyreducing theirholding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the joists. The use of an "edge to edge" stud
finderis highlyrecommended.
WARNING
• Always attach concrete expansion anchors directly to
load-bearingconcrete.
• Neverattach concreteexpansion anchorstoconcrete
coveredwith plaster,drywall,orotherfinishingmaterial.
WARNING

ISSUED:08-21-02 SHEET #: 200-9405-9 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
4 of 6
Threadsupportpipe(C)intothreadedfittinginceilingplate(K).Tighten-fourorfivecompleteturns-leavingslot
aligned with one small hole in the side of the ceiling plate threaded fitting. Insert and tighten one M5 x .8 x 10 mm
penta-pin screw (E) as shown. Use the M5 penta-pin tool (I) to tighten screw. BY HAND, insert four M10 x 1.5 x
15 mm penta-pin screws (G)intothreaded holesinthe sidesof ceiling armbox (A). Leaveapproximately 1/4”of
exposedthread.Slideceilingarmbox (A)andfiberwasher(F)ontoend ofsupportpipe(C).Threadretainingcollar
(D)ontothreaded endof supportpipe(C). Tighten -four orfivecomplete turns. Slideceiling arm box(A) downso
that it is on top of retaining collar (D). Insert and tighten one M5 x .8 x 10 mm penta-pin screw (E) into retaining
collar (D) as shown. Insert one M5 penta-pin screw (E) through the tab on the back of ceiling arm box (A). Use
M5 penta-pin tool (I) to tighten screw just enough to stabilize support pipe (C).
E
C
C
A
F
D
G
1/4”
G
E
E
K
BACKOF CEILING
ARMBOX
D

ISSUED:08-21-02 SHEET #: 200-9405-9 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
5 of 6
Hang tilt bracket (B) onto ceiling arm box
(A).Adjust tilt as desired and tighten four
M10 x 1.5 x 15 mm penta-pin screws (G)
securelyusingM10penta-pintool (H).
B
A
G
Attach tilt bracket (B) to adapter plate using four M10 x 15 mm penta-pin screws (G)
inaccordance withappropriate drawingbelow. Tighten usingM10 penta-pintool (H).
G
B
Note: Refertoadapter plateinstruction sheetfor attachmentofadapter plateto plasma beforeproceeding with step3.
LANDSCAPE
LANDSCAPE
LANDSCAPE
B
A
G
B
G
ADAPTERPLATE
ADAPTERPLATE
PLASMASCREEN
PLASMASCREEN
Note: Screenand adapter
platemay appeardifferent
thanillustrated.
• For a safe assembly be sure to fully tighten four
screws(G).
WARNING
PORTRAIT
(Not to be used with UNL models)
PORTRAIT
(Not to be used with UNL models)
• Donot mountPLCMUNL-CPinportrait orientation.
MountingPLCM UNL-CPin portraitorientation may
resultin productfailure.
WARNING

ISSUED:08-21-02 SHEET #: 200-9405-9 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
6 of 6
ADAPTERBRACKET
B
J
Attach tilt bracket (B) to adapter bracket using four M5 x 8 mm phillips screws (J).
Note: Do not use M5 x 6 mm screws that are included with the adapter bracket.
Note: Refertoadapterbracketinstruction sheetfor attachmentof adapterbracket toLCDscreen before
proceedingwithstep3.
Hang tilt bracket (B) onto ceiling arm box (A).Adjust tilt as desired and tighten four
M10 x 1.5 x 15 mm penta-pin screws (G) securely using M10 penta-pin tool (H).
B
A
G
©2004PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries, Inc.
Solid•PointisatrademarkofPeerlessIndustries,Inc.
Allother brand and productnames are trademarks or registered trademarks oftheir respective owners.
Note:Screen andadapter
platemay appeardifferent
thanillustrated.
LCDSCREEN
• For a safe assembly be sure to fully tighten four
screws(G).
WARNING