PEERLESS SF630P-S and assembly Guide

Max UL Load Capacity: 80 lb (36.3 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 04-18-05 SHEET #: 201-9427-6 02-06-07
Features:
• For 10" to 24" LCD flat panel screens
• Ultra-slim design holds the screen flat against the wall
Installation and Assembly:
SmartMount™ Universal Flat Wall Mount
for 10" - 24" LCD Flat Panel Screens
Models: SF 630P, SF 630P-S, SF 630, SF 630-S
This product is UL Listed. It must be
installed by a qualified professional
installer.
R

2 of 7 ISSUED: 04-18-05 SHEET #: 201-9427-6 02-06-07
Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
•studfinder("edgetoedge"studfinderisrecommended)
•phillipsscrewdriver
•drill
•1/4" bit for concrete and cinder block wall
•5/32" bit for wood stud wall
•level
Accessories
• Metal Stud Fastener Kit (ACC 215) (Not evalutated by UL)
• VideoConferencingShelf(ACC309)(Not evalutated byUL)
• Accessory Shelves (PM 600, PM 610) (Not evalutated by UL)
• Donot begin to install your Peerless product until you have read and understood the instructions andwarnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
callPeerless customer careat 1-800-865-2112.
• Thisproduct should only be installed bya qualified professional.
• Makesurethat the wall will safely support the combined load of the equipment and all attached hardware and compo-
nents.
• Neverexceed the Maximum UL Load Capacity of 80 lb (36.3 kg).
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edgeto edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrews firmly, butdonot overtighten. Overtightening candamage the items, greatly reducingtheir holding
power.
WARNING
Table of Contents
Parts List..............................................................................................................................................................................3
Installation to Single Wood Stud Wall...................................................................................................................................4
Installation to Solid Concrete or Cinder Block .......................................................................................................................5
Attaching Hook Bracket to Flat Panel Screen ......................................................................................................................6
InstallingandRemovingFlatPanelScreen ...........................................................................................................................7
Forcustomer care call [phone] or [phone].

3 of 7 ISSUED: 04-18-05 SHEET #: 201-9427-6 02-06-07
SF 630P SF 630P-S SF 630 SF 630-S
Description Qty Part # Part # Part # Part #
Awall plate 1 095-1320 095-4320 095-1320 095-4320
Bhook bracket 1 095-1321 095-4321 095-1321 095-4321
CM5 x 12 mm screw 2 520-1027 520-1027 520-1064 520-1064
DM4 x .7 x 10 mm phillips screw 4 504-9012 504-9012 504-9012 504-9012
EM4 x .7 x 20 mm phillips screw 4 504-9020 504-9020 504-9020 504-9020
F.198 ID x .313 OD x .437 H retaining spacer 4 590-5005 590-5005 590-5005 590-5005
G#14 x 2.5" hex head wood screw 2 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03
HAlligator® anchor 2 590-0097 590-0097 590-0097 590-0097
I4 mm allen wrench 1 560-1145 560-1145
Parts List
AB
D E G HFC
I

4 of 7 ISSUED: 04-18-05 SHEET #: 201-9427-6 02-06-07
Installation to Single Wood Stud Wall
1Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended. Based
on its edges, draw a vertical line down the stud’s center. Place wall plate (A) on wall as a template, making sure that
the two mounting holes are over the stud centerline. Level plate, and mark the center of the two holes. Drill two
5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate is level, secure it using two #14 x 2.5"
wood screws (G) as shown.
Skip to step 2 on page 6.
• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and
components.
WARNING
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highly recommended.
• Hardwareprovided is for attachment ofmount through standard thickness drywallor plaster into wood studs.Installers
areresponsible to providehardware for othertypes of mounting situations.
WARNING
G
A

5 of 7 ISSUED: 04-18-05 SHEET #: 201-9427-6 02-06-07
Installation to Solid Concrete or Cinder Block
1Make sure that wall plate (A) is level, use it as a
template to mark two mounting holes. Drill two 1/4"
(6 mm) dia. holes to a minimum depth of 2.5" (64
mm). Insert anchors (H) in holes flush with wall as
shown(right). Place wall plate over anchors and
secure with two #14 x 2.5" screws (G). Level, then
tightenall fasteners.
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to
avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware
and components.
WARNING
CUTAWAY VIEW
INCORRECT
concrete
surface
1
3
2
Drill holes and insert anchors (H).
CORRECT
Place plate (A)over anchors (H) and secure with screws (G).
Tighten all fasteners.
wall
plate
plaster/
drywall
concrete wall plate concrete
plaster/
drywall
• Always attach concrete expansion anchors directly to
load-bearingconcrete.
• Neverattach concrete expansionanchorsto concrete
coveredwith plaster,drywall, or otherfinishing mate-
rial.If mounting to concrete surfacescovered with a
finishingsurface isunavoidable, the finishingsurface
must be counterbored asshown below. Be sure
concreteanchors do not pull away from concrete
whentightening screws. If plaster/drywall is thicker
than 5/8", custom fasteners must be supplied by
installer.
WARNING
A
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
H
G
G
CINDERBLOCK
SOLID
CONCRETE
AH
H

6 of 7 ISSUED: 04-18-05 SHEET #: 201-9427-6 02-06-07
Attaching Hook Bracket to Flat Panel Screen
ThreadM5 phillips screws (C) to hook bracket(B)
making the screws flush with bracket as shown in
figures2.1and2.2.
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
F
*For screens with a hole
pattern in a pocket,
spacers (F) go between
hook bracket (B) and
screen.
D
FORVESA100MOUNTINGPATTERN:
Choosehole pattern as shown below. Attach hook
bracket (B) to back of screen using four M4 x 10 mm
screws(D)asshown below.
D
2
3FORVESA®75MOUNTINGPATTERN:
Choosehole pattern as shown below. Attach hook
bracket (B) to back of screen using four M4 x 10 mm
screws(D)asshown below.
*Note: If hole pattern is in a pocket, attach hook
bracket (B) to back of screen using four M4 x 20 mm
screws(E)and fourretaining spacers(F)asindicated
below.
B
CC
B
fig. 2.1 fig. 2.2
B
B

7 of 7 ISSUED: 04-18-05 SHEET #: 201-9427-6 02-06-07
Hookscreen onto wall plate (A) figure 4.1. Tighten
M5 x 12 mm screws (C), shown in figure 4.2 and
detail 1.
Note: For security models, tighten M5 x 12 mm
screws (C) using 4 mm allen wrench (I)
Toremove screen frommount,loosen screws (C)
and lift screen off of mount.
Installing and Removing Flat Panel Screen
4A
SCREEN
• Do not lift more weight than you can handle. Use
additionalman powerormechanical lifting equipment
to safely handle placement of the screen.
• Failure to lock hook bracket with screws (C) can
cause screen to come off mount if hit accidentally.
• Do not tighten screws with excessive force.
Overtighteningcan causedamage to mount. Tighten
screws to 20 in. • lb (2.26 N.M.) maximum torque.
CAUTION
WARNING
DETAIL 1
fig. 4.2
fig. 4.1
A
C
B
BA
C
©2007,PeerlessIndustries,Inc.Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.