PEERLESS SGLS01 Guide

Max Load Capacity:
150 lb (68 kg) screen
50 lb (22.7 kg) per shelf
3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 07-28-06 SHEET #: 202-9156-4 11-20-06
Installation and Assembly: 32" - 50" Flat Panel TV Stand
Model: SGLS01, SGLB01

2 of 30 ISSUED: 07-28-06 SHEET #: 202-9156-4 11-20-06
Note: Read entire instruction sheet before you start installation and assembly.
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
callPeerlesscustomercareat1-800-729-0307.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Makesure that the supportingsurface will safely supportthe combined load ofthe equipment and allattached hard-
wareandcomponents.
• NeverexceedtheMaximumLoadCapacity.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrewsfirmly,butdonotovertighten.Overtighteningcandamagetheitems,greatlyreducingtheirholding
power.
• The floor stand is not affixed or secured to the floor, and may therefore tip over and/or fall if screen and/or stand is
shaken or hit.Always monitor children and do not let children play alone around stand as they could get hurt by a
fallingscreen. Not recommended for usein areas with heavy traffic.
WARNING
Table of Contents
Parts List..........................................................................................................................................................................3, 4
AssemblingFloorStand........................................................................................................................................................4
AttachingScreenUsingUniversalPlatewithAdapterBrackets ................................................................................................7
AttachingScreen with VESA 100 Mounting Pattern...............................................................................................................10
Tools Needed for Assembly
•level
•phillipsscrewdriver

3 of 30 ISSUED: 07-28-06 SHEET #: 202-9156-4 11-20-06
Description Qty. Part # Part #
Ascreen mount bracket 1 201-4156 201-1156
Bhook plate 1 201-4157 201-1157
Cshelf support 1 201-4158 201-1158
Dshelf clamp bracket 1 201-4159 201-1159
Ebase 1 201-4168 201-1168
Funiversal plate 1 201-4109 201-1109
Gadapter bracket 2 200-0751 200-0750
Hupright 1 580-4180 580-1180
Iglass shelf 1 590-0208 590-0208
Jtop cover 1 590-4210 590-1210
Kbutton bumper 9 590-1209 590-1209
L1/4-20 x 12 mm decorative screw 12 520-1325 520-2325
M1/4-20 x 20 mm decorative screw 2 520-1326 520-2326
N1/4-20 nut 10 530-2022 530-1022
O5/16" flat washer 8 540-9446 540-9406
P 3/8-16 x 2.5" socket screw 3 520-9550 520-9550
Q7/32" allen wrench 1 560-9715 560-9715
R4 mm allen wrench 1 560-9646 560-9646
Sadhesive felt 1 570-0043 570-0043
TM10 x 15 mm socket screw 4 520-9262 520-9262
U6 mm allen wrench 1 560-9716 560-9716
Parts List
I
Some parts may appear slightly different than illustrated.
AB
C
D
E
G
F
H
J
QR
S
U
T
O
P
N
M
L
K
SGLS01 SGLB01

4 of 30 ISSUED: 07-28-06 SHEET #: 202-9156-4 11-20-06
M6 x 20 mm (4)
520-9402
M6 x 30 mm (4)
510-9109 multi-washer(6)
580-1036
M8 x 16 mm (6)
520-9257
M8 x 40 mm (4)
520-1136
M4 x 12 mm (6)
504-9013
Phillips Adapter Bracket Fasteners
M4 x 25 mm (4)
504-1015
M5 x 12 mm (4)
520-1027 M5 x 25 mm (4)
520-9543
M6 x 12 mm (4)
520-1128
M6 x 25 mm (4)
520-1208
I.D. 5.6 mm (4)
540-1057
M8 x 25 mm (4)
520-1031
I.D. 8.7 mm (4)
540-1059
1Cut adhesive felt (S) into four pieces as shown in figure 1.1 below and affix to bottom of base (E).
1-1 Attach upright (H) to base (E) using three 3/8-16 x 2.5" socket screws (P). Tighten screws using 7/32"
allenwrench(Q).
PE
H
S
1-2
CORDMANAGEMENTHOLE
CORDMANAGEMENTHOLE
Runcords through upright (H)using cord management holesas shown in figure 1.2.
fig 1.1 fig 1.2
H

5 of 30 ISSUED: 07-28-06 SHEET #: 202-9156-4 11-20-06
Insertthree button bumpers (K)into bottom of shelf
clamp bracket (D).
Attach shelf clamp bracket (D) to shelf support
(C) using two 1/4-20 x 20 mm screws (M) and
two1/4-20 nuts (N).
Insert six button bumpers (K) into shelf support (C).
2Loosely attach four 1/4-20 x 12 mm screws (L),
washers (O), and 1/4-20 nuts (N) to shelf
support(C).
LO
C
N
Slideshelf support (C) onto upright (H) so that 1/4-20
nuts (N) slide into slots of upright (H) as shown in
figure 3 and detail 1. Slide shelf support to desired
position, level, then tighten 1/4-20 x 12 mm screws
(L) using 4 mm allen wrench (R).
C
H
N
HSLOT
fig 3
DETAIL 1
3
I
K
C
4
4-1 Place glass shelf (I) on shelf support.
5
5-1
K
N
DM
C
L
NOTE: Maxof two shelves can be used
Max height of top shelf is 34" from base.
Max height of second shelf is 28" from base.
3-1

6 of 30 ISSUED: 07-28-06 SHEET #: 202-9156-4 11-20-06
Insert two 1/4-20 x 12 mm screws (L) into screen
mountbracket (A), leaving 1/8" of exposed thread as
shown in figure 9 and detail 3.
Loosely attach four 1/4-20 x 12 mm screws (L),
washers (O), and 1/4-20 nuts (N) to screen mount
bracket(A).
6
LOA
N
7Slide screen mount bracket (A) onto upright (H) so
that 1/4-20 nuts (N) slide into slots of upright (H) as
shown in figure 7 and detail 2. Slide screen mount
bracket to desired position, level, then tighten 1/4-20
x 12 mm screws (L) using 4 mm allen wrench (R).
A
H
SLOT
fig 7
L
8
J
H
Snaptop cover (J) onto upright (H). 9
1/8"
fig 9
DETAIL 3
L
A
DETAIL 2
N
H

7 of 30 ISSUED: 07-28-06 SHEET #: 202-9156-4 11-20-06
Attach universal plate (F) to hook plate (B) using four
M10 x 15 mm socket screws (T). Tighten screws
using 6 mm allen wrench (U).
10
F
B
T
Attaching Screen Using Universal Plate withAdapter Brackets
For attaching screens with VESA 100 hole pattern, skip to page 10.
11 Attach hook plate (B) to screen mount bracket (A).
B
A
12 Insert two 1/4-20 x 12 mm screws (L) into holes indicated below for desired screen orientation. Tighten all screws
using 4 mm allen wrench (R).
L
LL
2° Backward Tilt 5° Forward TiltNo Tilt

8 of 30 ISSUED: 07-28-06 SHEET #: 202-9156-4 11-20-06
Note: "X"dimensionsshouldbeequal.
• Tightenscrewsso adapter brackets are firmly
attached. Do not tighten with excessive force.
Overtighteningcancausestressdamageto
screws,greatlyreducingtheirholdingpowerand
possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.)
maximumtorque.
WARNING
Installing Adapter Brackets
Refer to Screen Compatibility Chart to determine the proper fasteners to use.
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place
screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.
Place adapter brackets (G) on back of screen, align to holes, and center on back of screen as shown in figure 13.1.
Attach the adapter brackets to the back of the screen using the appropriate combination of screws, multi-washers,
and spacers as shown in figure 13.3.
Note: Top and bottom holes must always be used.
Verify that all holes are properlyaligned,and then tighten screws using a phillipsscrewdriver.
• If screws don't get three complete turns in the screen
inserts or if screws bottom out and bracket is still not
tightly secured, damage may occur to screen or
productmay fail.
WARNING
MEDIUMHOLEFORM5SCREWS
SMALLHOLEFORM4SCREWS
LARGEHOLEFORM6SCREWS
fig. 13.2
G
CENTERBRACKETS
VERTICALLYONBACKOF
SCREEN
X
X
fig 13.1
Notes:
• Thenumberoffastenersusedwillvary,
dependinguponthetypeofscreen.
• Multi-washers and spacers may not be
used,dependinguponthe type of screen.
• Use the corresponding hole in the multi-
washer that matches your screw size as
showninfigure 13.2.
SCREWS
SPACERS
G
fig 13.3
MULTI-
WASHER
MULTI-WASHER
13

9 of 30 ISSUED: 07-28-06 SHEET #: 202-9156-4 11-20-06
Mounting and Removing Flat Panel Screen
Hook adapter brackets (G) onto universal plate (F), then slowly swing screen in as shown. Turnscrewsclockwiseat
leastsixtimes to prevent screen from being removed asshownin detail 4.
Note:Tightenusing4 mmallenwrench(R).
Screen can be adjusted horizontally if desired.
Note: It is important to lock screen down!To lock the screen down, tighten screws to adapter bracket as shown in
detail4.
Toremovescreenfrommount,loosenscrews,swingscreenawayfrommount,and liftscreenoffof mount.
14
G
DETAIL 4
SCREWS
F
G
• Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.
WARNING
F

10 of 30 ISSUED: 07-28-06 SHEET #: 202-9156-4 11-20-06
©2006PeerlessIndustries,Inc.Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
10
Attaching Screen with VESA100 Mounting Pattern
• If screws don't get three complete turns in the screen inserts or if screws bottom out and hook plate is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
Choose hole pattern as shown in figure 10. Attach
hook plate (B) to back of screen using four M4 x 12
mm screws. Tighten screws using a phillips screw-
driver.
M4X 12 MMSCREWS
fig 10
Attach hook plate (B) to screen mount bracket (A).
B
A
11
12 Insert two 1/4-20 x 12 mm screws (L) into holes indicated below for desired screen orientation. Tighten all screws
using 4 mm allen wrench (R).
L
LL
2° Backward Tilt 5° Forward TiltNo Tilt
B