Pegasus PFH-9210 Series User manual

INSTALLATION INSTRUCTIONS
PFH-9210-620-1/W Long Range Proximity Reader
—INTRODUCTION :
PFH-9210-620-1/W is one of the most secure indoor/outdoor longrange RFID reader which is an advanced RFID active reader
with smart design. It supplies with the top reliability and performance.
—SPECIFICATIONS :
Model N
o
.
PFH
-
9210
Card / Keytag PFH-620
Dimension 270 (L) x 270 (W) x 39 (H) mm
Mounting Surface Mount, waterproof
Reading Range Max. 6 meters
Operating Temperature -20°C ~60°C
Humidity 10% ~ 90%RH, non condensing
Directivity Omni-directional
Modulation Transmit coded –ASK, Receiving –Super Heterodyne
Operating Frequency 433.9 MHz
Output Format Wiegand output
Indications 3color LEDs( Red, Amber and Green )
Buzzer No (Built-in driver for external buzzer)
Operating Voltage / Current 15 VDC, 300 mA
Material ABS
Weight 2.00 Kgs ±5%
—INSTALLATION GUIDE :
1. Please select an appropriate place to install the reader and mark the locationof mounting holes through the screw holes of the
template.
2. When the reader is power on, the right LED will turn to Red; if the legal card is read, the left LED will turn to Green.
3. The card reading is valid only when the middle LED turn to Amber.
4. Please make sure15 VDC linear type (not switching type) power supply that is isolated from other devices.
5. Once you use a separate power supply for the reader, a common ground should be connected between the reader and control
system.
—WIRE CONFIGURATION :
Noted：1. The PIN C(green) or PIN D(blue) must be shorted to PIN B(black) DC V-to read the card.
2. The reader will only be powered when PIN G(Gray) is connected to +15V power supply (min. 300mA). The PIN
G(Gray) can be controlled by relay contacts which is controlled by timer delayed relay. After effective reading, it will be
disable for a few seconds during vehicle passes the gate. W-04-PFH9210-620-1-W/E
Pin No. Wire Color Function
ARed 15V DC +
BBlack DC V-
CGreen DC V-
DBlue --
EWhite Data 1
FYellow Data 0
GGray
Long Range Proximity reader
Model：PFH-9210-620-1/W
Ver.6.02
Vehicle loop detector

—FRONT PANEL：
—BACK :
W-04-PFH9210-620-1-W/E
LED
：
Red
（Power On）
LED
：
Green
（Legal Access）
163mm
270mm
270mm
Screw hole
(#8
＊
1
-
1/2)
Screw hole
(#8
＊
1
-
3/4)
Screw hole
Dig out hole
Dig out hole
41.5mm ?PACKAGE CONTENTS
DESCRIPTION Q’TY
Screw
Screw (M5X20)
Screw nut
Washer
Switching Power supply 15VDC
Sticker
Manual
2pcs
2pcs
2pcs
2pcs
1pc
2pcs
1pc
?TimerTable:
456Stop
Time
OFF OFF OFF 0.5s
ONOFF OFF 1s
OFF ON OFF 2s
ON ON OFF 3s
OFF OFF ON 5s
ON OFF ON 7s
OFF ON ON 10s
ON ON ON 18s
Default Value
LED
：
Amber
(Standby)
●SW1 definition
SW Function ON OFF
SW#1 Loop sensorcheck Check Entry/Exit sensor Not check Entry/Exit sensor
SW#2 Operation mode Time mode Automatic mode
SW#3 Double reading check NO YES
SW#4~#6 Time selection Refer to timer table
●Example A: Automatic mode ( “?”: means don’t care ) Send signal one time only
123456Function
ON OFF ON
???●Reading the card only one time
●Example B: Timer mode (Periodically send signal by timer)
123456Function
ON ON ON OFF OFF ON ●Periodically send signal every 5
seconds
Screw hole
for bracket
Optional accessory: the bracket for PFH-9210 series: (Model no. : PGV-BRACKET/L205)

—Installation of Parking Controls:
Install of two PFH-9210-620 at different place individually
Installation Location:
1. Leave over 6m between entrance and exit reader to avoid the both frequencies interfering with each other.
2. Install Reader at the left side of vehicle lane,and place the Tag at the left top windshield of car.
Install Two PFH-9210-620
Installation Location:
1. Leave over 6m between entrance and exit reader to avoid the both frequencies interfering with each other.
2. Install Reader at the right side of vehicle lane, and place the Tag at the right top windshield of car.
W-04-PFH9210-620-1-W/E

IR Sensor Vehicle loop detector
FCC Statement
—Federal Communication Commission Interference Statement
This equipment hasbeen tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
. Consult the dealer or an experienced radio/TVtechnician for help.
—FCC Caution :
To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment. (Example-use only shielded interface cables when connecting to
computer or peripheral devices).
Specifications are subject to change without any notice for further modification.
W-04-PFH9210-620-1-W/E

+15V
PP-2752 Connecting Diagram Of Long Range Hand Free Vehicle
Access Control System
Ver.5.02
PP-2752 Controller 4 PIN Wiegand port (white)-JC、JD PFH-9210-620-1/W Receiver 7PIN wire
1.(Red) -- 1.A(Red)—+15V Input Entry sensor
2.(Yellow) --Data 1 2.B(Black)—DC GND-
3.(Green) --Data 0 3.C(Green)
4.(Black) –Ground 4.D(Blue) Exit sensor
5.E (White) —Data 1
6.F(Yellow)—Data 0
7.G(Gray) —Power for reader
Noted：1. The PIN C(green) or PIN D(blue) must be shorted to PIN B(black) DC Ground to read the card.
2. The reader will only be powered when PIN G(Gray) is connected to +15V power supply (min. 300mA). The PIN
G(Gray) can be controlled by relay contacts which is controlled by timer delayed relay. After effective reading, it will be
disable for a few seconds during vehicle passes the gate.
PP-2752 Controller 9 PIN connector JA (blue) Controller 8PIN connector JB (white)
1.(Red)—+12V A.(Brown)
2.(Black)—GND B.(Red)
3.(Brown)—Common COM C.(Orange)
4.(Orange)—Common(FORM A) N.O. D.(Yellow)
5.(Yellow)—Common(FORM B) N.C. E.(Green)—COM
6.(Green) F.(Blue) —N.O.
7.(Blue)—Exit push button G.(Purple)
8.(Purple)—Door monitoring H.(Gray)
9.(Gray)—Printer output
Remarks: 1. you could use sensor coil controller or IRF sensor to compatible with entry / exit sensor.
2. sensor contact：it’s a dry contact, when the vehicle reach it becomes short output which is outputted by coil
sensor or IRF sensor.
3. The PP-2752 could parallel many PFH-9210-620-1/W receiver boxes at the same time, but the distance of
receiver box and receiver box has to be kept min. 2 meters.
The max. distance of PP-2752 &
PFH-9210-620-1/W is 30 meters. ( vehicle loop detector or
IR sensor)
}Barrier 2
}Barrier 1

PFH-620
PFH-9210-620-1/W
PFH-9210-620-1/W
PC Host
PP
-
2
PCP832
-
2
-
AZ
Sensor Coil
2C steel-cored cable
Sensor Coil controller
2C 24AWB
PFH-9210-620-1/W
6C 24AWG UL2464
PP-2752
4C 10C
Barrier PC
6C
Push button
* When a car passes a sensor coil, the
sensor coil controller will start
PFH-9210-620-1/W to receive signal of
PFH-620 hand free card. If the PFH-620 card
is legal, the PFH-9210-620-1/W will place an
order to open the barrier and store all access
records in PP-2752, you also could connect
PP-2752 to PC and upload all access
records to PC.
* Push button is used in emergency.
*The distance of PP-2752 and
PFH-9210-620-1/W can’t exceed 30 meters.
* Our PP-2752 has Anti-pass back function,
please follow below points and decide
whether use the function or not.
1. It’s a better environment when entrance
and exit is not a same lane.
2. If entrance and exit is a same lane, you
could install coil sensor or IRF sensor to
assist our system to judge the direction
of cards. Nevertheless, below
situations may happen wrong
judgment.
a. Two-way lane has cards
b. Another card follow closely front
card.
Software
PFH-620
Push Button
Optional installation