peitel PTCarPhone 5 Series User manual

CAUTION: Non-compliance with these instructions can cause damage to the device
and to the vehicle.
Qualied installation personnel
The device must only be installed in the vehicle and serviced by qualied specialists.
Consequences of incorrect installation
Incorrect installation can cause damage to the vehicle. Incorrect assembly or ser-
vice can have hazardous consequences and can void the warranty and possibly the
operating permit of your vehicle.
Airbag
With vehicles that are equipped with an airbag, remember that the airbag lls with
a strong force. Do not install any components in the area impacted by the lled
airbag.
Antennas
Before start-up of the device, the GSM or UMTS antenna and the GPS antenna, for a
device with integrated GPS module, must be connected (antennas are not included
in the scope of supply). The device must not be operated without antenna(s), since
this can lead to the destruction of the device.
Connection to the power supply of the vehicle
In some cases settings must be done in modern vehicles after attaching the bat-
tery. Absolutely be sure to refer to the operating manual of your vehicle for this.
Environmental inuences: Water and dust
The PTCarPhone and all accessories are neither dustproof nor waterproof. Make
sure that the PTCarPhone is always protected from moisture and from water pene-
trating the vehicle. Prevent penetration of dust particles in the housing by cleaning
regularly.
More information is available in “PTCarPhone 5Series Operating Manual” at:
http://www.ptcarphone.de/en/downloads
!
Precautionary Measures during Installation
Article number: 6053-085-014-00 - 02/2017
Setting up the PTCarPhone
Inserting the SIM card
A valid and activated SIM card is required
to operate the device. This is available
from your mobile phone provider. It saves
all the important data of your connection.
To open the SIM card holder, push the
round button in the housing with a point-
ed object. Place the SIM card in the holder
and push it back in the electronics box.
NOTE:
Insert the SIM card only if the device
and the vehicle ignition are turned off.
Make sure to insert the SIM card hold-
er in the correct position. Closing does
not require strong force.
If a piece of plastic remains on the
edge of the SIM card when taking it
out, it is necessary to remove this
before inserting the SIM card.
Inputting PIN
If a PIN is required it will be requested
with an appropriate message when start-
ing the device.
Enter the PIN using the input keys and
conrm with the OK function key. Correc-
tions can be made with the Delete function
key.
PIN input is shown with asterisks so that
it cannot be seen. The subsequent
registration in the network can take a few
seconds.
After entering an incorrect PIN three
times the SIM card is blocked. The PUK is
requested for unblocking.
Setting the delay time
After turning off the ignition the device
runs for the set delay time and then turns
off.
Use the following menu path to set the
delay time:
System > Conguration > device code
input > Delay timer
The device code at delivery is: 0000
Software update
Software updates for the handset and
PTCarPhone are done via the Internet
access of the mobile network. Therefore,
Internet access must be set up before-
hand.
System > Device info > Update > device
code input > Update process
The device code at delivery is: 0000
Turning on virtual ignition
In modern vehicles without ignition wiring
it is recommended to activate the Virtual
ignition function.
System > Conguration > device code
input > Virtual ignition
The device code at delivery is: 0000
Technical details of the connections
Line-out connection
To connect to the vehicle audio system.
Galvanically isolated
Can be extended as needed
I/O connections
The TPU has six freely programmable
inputs and outputs:
Model: Open-Drain output (wired
ground) with recovery diode / input
with 15 kOhm pull-up resistor against
the device operating voltage
Only ohmic and inductive loads are
allowed (no capacitive loads!)
Maximum current carrying capacity:
150 mA per connection
Dielectric strength smaller than/equal
to the connected device operating
voltage (however, max. 32 V)
Recovery diode for relay (inductive
loads) included; use of device-specic
power supply (pins 4, 5, 6) is required
for this
Radio mute output
Model: Open-Drain output (wired
ground)
Only ohmic loads allowed!
Maximum current carrying capacity:
50 mA
Maximum dielectric strength against
ground: +32 V
Imprint
© 2017 pei tel Communications GmbH. All rights reserved.
pei tel Communications GmbH, Rheinstr. 15 A, 14513 Teltow, Germany
pei tel reserves the right to modify these instructions at any time, to correct typing mistakes or to add new functions in the course of technical progress or further develop-
ment. Every current version of these instructions can be found on the Internet at http://www.ptcarphone.de/en/downloads.
Legal notices
pei tel accepts no liability for maintaining settings, data or text messages saved on the PTCarPhone. Some of the services, company names and trademarks given in these
instructions are the property of the respective trademark owners.
Installation Instructions
PTCarPhone 5 Series
The professional car phone with hands-free
equipment for permanent installation
ENGLISH
www.ptcarphone.de
A member of the peiker group

CAUTION: Non-compliance with these instructions can cause damage to the device
and to the vehicle.
Qualied installation personnel
The device must only be installed in the vehicle and serviced by qualied specialists.
Consequences of incorrect installation
Incorrect installation can cause damage to the vehicle. Incorrect assembly or ser-
vice can have hazardous consequences and can void the warranty and possibly the
operating permit of your vehicle.
Airbag
With vehicles that are equipped with an airbag, remember that the airbag lls with
a strong force. Do not install any components in the area impacted by the lled
airbag.
Antennas
Before start-up of the device, the GSM or UMTS antenna and the GPS antenna, for a
device with integrated GPS module, must be connected (antennas are not included
in the scope of supply). The device must not be operated without antenna(s), since
this can lead to the destruction of the device.
Connection to the power supply of the vehicle
In some cases settings must be done in modern vehicles after attaching the bat-
tery. Absolutely be sure to refer to the operating manual of your vehicle for this.
Environmental inuences: Water and dust
The PTCarPhone and all accessories are neither dustproof nor waterproof. Make
sure that the PTCarPhone is always protected from moisture and from water pene-
trating the vehicle. Prevent penetration of dust particles in the housing by cleaning
regularly.
More information is available in “PTCarPhone 5Series Operating Manual” at:
http://www.ptcarphone.de/en/downloads
!
Precautionary Measures during Installation
Article number: 6053-085-014-00 - 02/2017
Setting up the PTCarPhone
Inserting the SIM card
A valid and activated SIM card is required
to operate the device. This is available
from your mobile phone provider. It saves
all the important data of your connection.
To open the SIM card holder, push the
round button in the housing with a point-
ed object. Place the SIM card in the holder
and push it back in the electronics box.
NOTE:
Insert the SIM card only if the device
and the vehicle ignition are turned off.
Make sure to insert the SIM card hold-
er in the correct position. Closing does
not require strong force.
If a piece of plastic remains on the
edge of the SIM card when taking it
out, it is necessary to remove this
before inserting the SIM card.
Inputting PIN
If a PIN is required it will be requested
with an appropriate message when start-
ing the device.
Enter the PIN using the input keys and
conrm with the OK function key. Correc-
tions can be made with the Delete function
key.
PIN input is shown with asterisks so that
it cannot be seen. The subsequent
registration in the network can take a few
seconds.
After entering an incorrect PIN three
times the SIM card is blocked. The PUK is
requested for unblocking.
Setting the delay time
After turning off the ignition the device
runs for the set delay time and then turns
off.
Use the following menu path to set the
delay time:
System > Conguration > device code
input > Delay timer
The device code at delivery is: 0000
Software update
Software updates for the handset and
PTCarPhone are done via the Internet
access of the mobile network. Therefore,
Internet access must be set up before-
hand.
System > Device info > Update > device
code input > Update process
The device code at delivery is: 0000
Turning on virtual ignition
In modern vehicles without ignition wiring
it is recommended to activate the Virtual
ignition function.
System > Conguration > device code
input > Virtual ignition
The device code at delivery is: 0000
Technical details of the connections
Line-out connection
To connect to the vehicle audio system.
Galvanically isolated
Can be extended as needed
I/O connections
The TPU has six freely programmable
inputs and outputs:
Model: Open-Drain output (wired
ground) with recovery diode / input
with 15 kOhm pull-up resistor against
the device operating voltage
Only ohmic and inductive loads are
allowed (no capacitive loads!)
Maximum current carrying capacity:
150 mA per connection
Dielectric strength smaller than/equal
to the connected device operating
voltage (however, max. 32 V)
Recovery diode for relay (inductive
loads) included; use of device-specic
power supply (pins 4, 5, 6) is required
for this
Radio mute output
Model: Open-Drain output (wired
ground)
Only ohmic loads allowed!
Maximum current carrying capacity:
50 mA
Maximum dielectric strength against
ground: +32 V
Imprint
© 2017 pei tel Communications GmbH. All rights reserved.
pei tel Communications GmbH, Rheinstr. 15 A, 14513 Teltow, Germany
pei tel reserves the right to modify these instructions at any time, to correct typing mistakes or to add new functions in the course of technical progress or further develop-
ment. Every current version of these instructions can be found on the Internet at http://www.ptcarphone.de/en/downloads.
Legal notices
pei tel accepts no liability for maintaining settings, data or text messages saved on the PTCarPhone. Some of the services, company names and trademarks given in these
instructions are the property of the respective trademark owners.
Installation Instructions
PTCarPhone 5 Series
The professional car phone with hands-free
equipment for permanent installation
ENGLISH
www.ptcarphone.de
A member of the peiker group

Connection Diagram and Assembly
Provider
System Speed D.
10:26
GPS antenna
(only for models with GPS module,
not in scope of supply)
GSM or UMTS antenna
(not in scope of supply)
I/O connections
Hands-free
microphone
Cable
set
Handset HA59
Connection for second handset
(not in scope of supply)
Electronics
box (TPU)
SIM card
holder
(SIM card not in
scope of supply)
Loudspeaker
Mini-USB
connection
(only for service
purposes)
Unlock key
Assembly Sequence
1. Become familiar with the connections. Disconnect the
negative terminal of the vehicle battery while follow-
ing the safety instructions of the vehicle manufacturer.
2. Select the installation locations for the electronics
box, handset, loudspeaker, hands-free microphone and
the antenna(s), paying attention to the cable lengths
and installation instructions and mount the compo-
nents.
When drilling holes make sure that the vehicle is not
damaged. Use cable bushings on sharp-edged holes.
3. Install the included hands-free microphone.
Make sure that air ow from the vents is not in the
direction of the microphone. Also refer to “Mounting
locations for the microphone” below.
Then install the loudspeaker (a good location is the
passenger footwell). During installation of the micro-
phone and loudspeaker make sure of sufciently large
spatial separation, to avoid acoustic feedback.
4. Connect the power supply cable (red) on the perma-
nent positive and the ignition input (yellow/black) to
the ignition *, if present. Do not connect the ignition
input (yellow/black) onto permanent positive, since
this limits the scope of function of the device.
Connection of the ground cable is done directly to
the vehicle battery, the central ground point (ground
block) or a part of the vehicle body.
* For vehicles without ignition wiring it is recommend-
ed at the end of the installation to activate the “Virtual
ignition” function.
5. Connect the violet cable with the mute input of the car
radio. This ensures automatic radio mute switching for
incoming and outgoing calls.
6. Insulate unused cables so no short circuits can occur.
7. Connect the individual components of the device with
each other using the plug and screw connections (see
connection diagram).
8. Check the total installation and insert a valid SIM card.
Connect the vehicle battery.
9. For vehicles with ignition wiring: Turn on the ignition.
The device now turns on and requests the input of the
PIN (if this was not deactivated on the SIM card).
For vehicles without ignition wiring: Turn the device
on with the end key /on the handset.
10. Enter the PIN. The telephone is now registered in the
network.
11. Make a call in order to check the basic functions.
12. Check whether there is new software available and if
necessary perform a software update. Downloading
of software updates can incur costs, depending on the
mobile phone contract.
13. If desired, make personal settings on the device (see
chapter “Setting up the PTCarPhone” on the back) and
nish the installation.
Mounting location for the microphone
Microphone alignment
A
C
B
Optimum position
Alternative position
Limited suitability
A
C
B
1
Maximum
sensitivity
Adhesive tape
for smooth
(at) surfaces
1
2
2
Scope of supply
Electronics box (TPU)
Handset HA59 with cradle
Loudspeaker
Hands-free microphone
2.5 m extension cable for handset
Cable set
Quick reference guide
Installation instructions
Available accessories
Handset HA59 incl. 5.0 m extension cable
Article number: 6508-006-100-51
I/O cable installation set (12x 200 mm strands and
plug housing)
Article number: 6708-004-000-00
2.5 m extension cable for the handset
Article number: 6098-260-005-51
5.0 m extension cable for the handset
Article number: 6098-260-007-51
Additional required hardware
GSM or UMTS antenna
Model-specic GSM or UMTS antenna with FME connec-
tion (not in scope of supply).
GPS antenna for devices with optional GPS
GPS antenna with SMA connection (not included in the
scope of supply). Power supply: 3.3 V, max. 50 mA;
SIM card
Mini-SIM card with mobile phone contract with phone
and data plan. This is available from your mobile phone
provider.
TIPS:
If the PTCarPhone should be operated with the same
telephone number as the mobile phone of the user, it
is recommended to use a so-called multi-SIM card. For
this, contact your mobile phone provider.
It is recommended to make sure before assembly,
whether the electronics box should be positioned so
that easy access to the SIM card is provided.
Screws and adhesive tape
Depending on the installation situation it can be nec-
essary to fasten the electronics box, the handset and
the accessories with other fastening material than that
which is partially supplied. Please do not forget: Safety
rst! Nevertheless, it is recommended to pay attention to
aesthetics.
Loudspeaker connection
Line-out (gy)
Vehicle ground (blk)
Ignition (yl/blk) (terminal 15)
Radio mute (vi)
Permanent positive (rd)
(terminal 30)
PIN Signal
1, 2, 3 GND
4, 5, 6 U
B
+
7 to 12 I/O 1 to 6
I/O connections
(Top view)
Types of connection:
Key connection
I/O
GND
Relay connection
UB+
I/O
CAUTION:
The respective operating voltage of the vehicle electrical
system is applied to the I/O connection. Please keep this
in mind when selecting your I/O components.
Technical data of the connections can be found on the back!
The “I/O connections manual” can be found at:
http://www.ptcarphone.de/en/downloads
4321
8765
1LSPK - (blk) 5LSPK + (wht)
2Line-out - (gy) 6Line-out + (gy)
3GND (blk) 7Ignition (yl/blk)
4Permanent
positive (rd)
8Radio mute (vi)
Cable set connection
(Top view)
12
654321
11 10 9 8 7
Abbreviations
UB+: Operating voltage PTCarPhone
GND: Vehicle ground (minus terminal)
I/O: Switch input/switch output
LSPK: Loudspeaker connection
TPU: TelePhoneUnit
blk: black
gy: gray
rd: red
wht: white
yl/blk: yellow/black
vi: violet
10 - 32 V