Pelonis PTH15A2BGB User manual

OWNER’S MANUAL
PTC CERAMIC HEATER
MODEL: PTH15A2BGB

1

Control Panel Functions
A
C
B
Power and Setting Control Power Indicator Light
Thermostat Control
OPERATION INSTRUCTIONS
• Place the heater on a firm level surface that is free of obstructions, and at least 3 ft. (0.9m) away
from all walls and other objects such as furniture, curtains, plants or combustible material.
• With the Power and Setting Control “A” in the “OFF” position, plug the heater into a grounded
120V outlet.
• Turn the heater “ON” by turning the Power and Setting Control “A” clockwise to the desired
power setting (LOW, HIGH, LOW & OSC or HIGH & OSC). The Power Indicator Light “B” will
illuminate. The power settings operate as follows:
LOW: The Fan and heating elements operate at LOW setting operates at 900W.
HIGH: The Fan and heating elements operate at HIGHT setting operates at 1500W.
LOW&OSC: The Fan and heating elements operate at LOW setting with oscillation.
HIGH&OSC: The Fan and heating elements operate at HIGHT setting with oscillation.
• Turn the Thermostat Control “C” to the desired setting between “MIN” and “MAX.”
IMPORTANT!
Your heater is equipped with a
polarized alternating current line plug
(a plug having one blade wider than
the other). This plug will fit into the
power outlet only one way. This is a
safety feature. If you are unable to
insert the plug fully into the outlet, try
reversing the plug. If the plug still fails
to fit, contact your electrician to
replace your outlet. DO NOT defeat
the safety purpose of the polarized
plug.
This heater includes a safety tip-over switch, which will shut the heater off in case
it is tipped over. If at any time, the heater does tip over, please put the heater back in
the upright position. The heater will resume its normal operation.
2
D
C
B
A

TROUBLESHOOTING
CLEANING AND STORAGE
Model No.: PTH15A2BGB
Voltage: 120V~, 60Hz
Current: Maximum continuous draw: 12.5 Amps
Output: 5200 BTUs
Power: LOW=900 Watts, HIGH=1500 Watts
Tolerances on all specifications:Approximately +5%
SPECIFICATIONS
If your heater fails to operate, please follow these instructions:
•Ensure that your circuit breaker or fuse is working properly.
•Be sure the heater is plugged in and that the electrical outlet is working properly.
•Check for any obstruction. If you find an obstruction, turn the heater “OFF.” Unplug
the heater and wait a few minutes for it to cool down. Carefully remove the
obstruction. Plug the heater in and turn it on again by referring to the OPERATING
INSTRUCTIONS.
NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR HEATER, PLEASE SEE THE WARRANTY
INFORMATION FOR INSTRUCTIONS. PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE
HEATER YOURSELF. DOING SO MAY VOID THE WARRANTY AND COULD CAUSE DAMAGE OR
PERSONAL INJURY. IF THE PROBLEM STILL PERSISTS, PLEASE CONTACT US BY REFERRING TO
THE SERVICE & SUPPORT INFORMATION ON THE FOLLOWING PAGE.
It is recommended that the heater be cleaned at least one time during the operating season in
order to provide the optimum level of performance. ALWAYS TURN THE POWER SWITCH OFF
AND UNPLUG THE HEATER BEFORE CLEANING.Be sure to save the box for off-season storage
•Turn the heater “OFF,” unplug it and wait for the heater to cool down.
•Use a dry cloth to clean only external surfaces of the heater.
•Do not use any cleaning agents or detergents.
•Never immerse the heater in water.
•Pack the heater in the original carton and store it in a cool and dry place.
This heater includes a thermal cut-off that shuts the heater off if it
overheats due to abnormal conditions. If this occurs, turn the heater "OFF", unplug
it, and inspect and remove any objects on or adjacent to the heater. Allow it to
cool for a few minutes, and then plug it back in and resume normal operation.
3

[email protected]
5 Sylvan Way, Suite 100
Parsippany, NJ 07054
4

5
Ceramic Tower Heater
Ceramic Tower Heater
Ceramic Tower Heater
Ceramic Tower Heater