Pelpro FPP User manual

TollFreeTechnicalSupport
1-866-456-9269
FPP
Bay View Freestanding
IPP
Bay View Insert / Built-In
FPP
Freestanding
IPP
Insert / Built-In
II or III
with Memory& Fan Trim
READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR HEATER.
FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE,
BODILY INJURY OR EVEN DEATH!
Installation shall conform to CAN/CSA B365 Installation Code for Solid-Fuel-Burning Appliances and
Equipment in Canada and NFPA 211 Chimney, Fireplaces, Vents and Solid Fuel Burning Appliances in the USA
.
Contact local building or fire officials to obtain a permit and information on any installation requirements
and installation inspection requirements in your area.
Rev. A, 01/2009

2
PelPro Appliances www.pelprostoves.com 2
Friendly Reminder:
A pellet stove / insert is not designed or tested as a primary source of heat. They are designed to
be a supplementary heat only. Please do not disconnect or remove your existing primary heat source.
Please do not disconnect or remove your existing primary heat source.
Dear Pellet Stove Owner:
UPDATES and REGISTRATION
PELPRO
CONGRATULATIONS on the purchase of your You
have selected the finest in residential wood pellet heating technology.
Let us pass on a few "tips" concerning installing your stove and heating with wood pellets.
1. Whether you install your stove yourself or hire a professional installer,
for the safety of your family and for efficient, satisfactory operation of your
stove.
2. is the most important step to ensure the efficient and
satisfactory
operation of your appliance for many years tocome.
3. Pellets can vary
greatly from
company to company, from load to load and occasionally from bag to bag.
4. Be extra .
5. Remember that a very high percentage of operational dilemmas with a pellet stove are
usually traced back to Improper installation, poor quality pellets and/or a lack of timely
cleaning.
With just a minimum of daily care your PELPRO pellet appliance will provide years of
clean, efficient, comfortable and environmentally sound heating.
Thank you for selecting aPELPRO wood pellet appliance.
Sincerely,
Canadian Comfort Industries &
Dansons Inc.
Up to date additions, product information, product registration and warranty extension
registration can be found on our website www.dansons.com/support
PELPRO Multi-fuel pellet appliance!
a quality
installation
is a must
Initial Burn Setup of the stove
Pellet Stoves ARE NOT plug ‘n
play.
Know the quality and characteristics of the pellets you burn.
diligent in your cleaning program

3
T
TABLE
ABLE
OF
OF
C CONTENTS
ONTENTS
GENERAL INFORMATION MAINTENANCE
SAFETY PRECAUTIONS 4 REQUIRED ROUTINE CLEANING 33
SAFETY TESTING 5 2 TO 3 DAYS OR WEEKLY
HOW YOUR PELPRO APPLIANCE WORKS 6 PERIODIC MAINTENACE 34
AUTOMATIC SAFETY FEATURES 7 1 TON, SEASONAL, BI-SEASONAL
SPECIFICATIONS 8 FALL START-UP35
ELECTRICAL REQUIREMENTS SPRING SHUT-DOWN 35
PRE PLANNING YEARLY MAINTENANCE CONTRACTS 36
PLANNING & INSTALLATION CHECKLIST 9 TROUBLE SHOOTING 36
PLANNING EXHAUST SYSTEMS REPLACEMENT PARTS 39
TYPE 10 LIMITED WARRANTY 40
SAFETY PRECAUTIONS
DETERMING SIZE & DISTANCE 11
TERMINATION 12
PLANNING OUTSIDE AIR 13
APPLIANCE PLACEMENT 14
FLOOR PROTECTION
CLEARANCES TOCOMBUSTIBLES
INSTALLATION
TOOLS OF THE TRADE 16
STEP BY STEP DIRECT VENT INSTALLATION 17
MOBIILE HOME 18
INSTALLATIONS OPTIONS 19
FIREPLACE INSERT—MASONRY OR FACTORY 20
BUILT-IN INSERT 22
OPERATION
BEFORE LIGHTING YOUR FIRST FIRE 24
USING THE ACUTRON CONTROLS 25
CHOOSING YOUR MODE OF OPERATION 26
MANUAL MODE
THERMOSTAT MODES (OPTIONAL) 27
UNDERSTANDING YOUR ACUTRON CONTROL 28
LIGHTING YOUR FIRE 29
PERFORMANCE ENHANCEMENT TIPS 30
FUEL
WOOD PELLETS 31
CORN AND OTHER BIOMASS 32
PelPro Appliances www.pelprostoves.com 3

4
S
SAFETY
AFETY
P PRECAUTIONS
RECAUTIONS
 BEFORE installing or having the pellet appliance installed contact the local building officials to obtain the
necessary permits and information on any installation restrictions or inspection requirements in your area
and notify your insurance company you have installed a pellet appliance.
 This unit must be properly installed to prevent the possibility of a house fire. The instructions and local
building codes requirements must be strictly adhered to. Do not; use makeshift methods or material that
may compromise the installation.
 When the pellet appliance is installed in a mobile home, the heater must be bolted to the floor, have out-
side air, and MUST NOT BE INSTALLED IN THE BEDROOM (Per H.U.D. requirements). Check with
local building officials.
 NEVER try to repair or replace any part of the heater unless instructions for consumer are given in this
manual or instructed by Dansons Customer Service Department. A trained technician should do all other
work.
 Educate all children of the danger of a high-temperature heater. Young children should be supervised
when they are in the same room as the heater.
 This heater is designed and approved for pelletized wood fuel, shelled corn, or wheat only. Any other
type of fuel burned in this heater will void the warranty and safety listing. Keep foreign objects out of the
hopper.
 NEVER use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start
or “freshen up” a fire in this appliance. Keep all such liquids well away from the appliance while it is in
use.
  This heater must be connected to a standard 115 V., 60 Hz 3-prong grounded electrical outlet in
accordance with local building codes, or in the absence of local codes, with the National Electrical Code,
ANSI/NFPA 70. A grounded surge-protection unit is recommended.
 Do not use an adapter plug or sever the grounding prong on the electrical plug.
 Do not route the electrical cord underneath, in front of, or over the heater.
 Do not unplug the stove if you suspect a malfunction.
Push the “OFF” Touch Pad and inspect the heater.
 The heater will not operate during a power outage. If a power outage does occur, check the heater for
smoke spillage and open a window if any smoke spills into the room.
 DO NOT operate the heater if you smell smoke coming from the heater. Push the “OFF” Touch Pad,
monitor your pellet appliance, and call your local authorized dealer.
 Do not place clothing or other flammable items on or near the heater. When installed with a thermostat
there is a possibility of the heater turning on and igniting any items placed on or near the unit.
 CAUTION: To prevent fingers, clothing or other objects from coming in contact with the auger; your appli-
ance is equipped with a shutoff switch which stops the auger when the hopper lid is open. THE AUGER
IS CAPABLE OF CAUSING SERIOUS INJURY AND THIS SWITCH MAY NOT BE DISCONNETED
IMPORTANT: Read, save and follow the instructions in this manual. It contains important safety, operating
and maintenance instructions you will need.
PelPro Appliances www.pelprostoves.com 4
RECOMMENED: For your and your families protection and well being, Dansons’ highly recommends
installing and maintaining both a smoke detector as well as a CO2 detector.

5
 DO NOT operate the stove if the flame becomes dark and sooty or if the firepot overfills with pellets. Push
the OFF Touch Pad and inspect the heater. (See Operating Your Stove). Soot or creosote may accumu-
late in the exhaust vent system when the stove is operated under incorrect conditions such as an ex-
tremely rich burn. The flame will have a lazy orange color with black tips. This indicates poor pellet fuel
combustion.
 NEVER block free airflow through the open vents of the unit. The viewing door and ash pan must be
closed and latched during operation.
 The pellet appliance exhaust system works with negative combustion chamber pressure and a positive
chimney pressure, therefore the exhaust system must be completely airtight and properly installed. All
exhaust system vent joints must be sealed, gas tight, with HI-TEMP RTV silicone sealant, and/or at least
3 sheet metal screws per joint and to the heater also.
 Your heater requires periodic maintenance and cleaning (Refer to ”Routine Cleaning” section of the
manual). Failure to maintain your heater may lead to smoke spillage in your home.
 Disconnect the power cord from the electrical outlet before performing any maintenance. Pushing ”OFF”
Touch Pad does not disconnect all power to the heater.
 BEFORE carrying out any maintenance or cleaning, allow the heater to cool. Ashes must be disposed in a
metal container with a tight lid and placed on a non-combustible surface or on the ground, well away from
all combustible materials, pending final disposal.
 The exhaust system should be checked twice a year minimum for any build-up of soot or
creosote. Do not touch the hot surfaces of the heater.
S
SAFETY
AFETY
T TESTING
ESTING
NOTE: Canadian Comfort Industries grants no warranty, implied or stated, for the installation or
maintenance of your appliance, and assumes no responsibility of any consequential damage(s).
In accordance with the procedures and specifications listed in UL1482–00 & ASTM E 1509-04, and
ULC-S627-00 and ULC-S628-M93 for solid fuel room heater. Tested and listed for use in Manufactured
Homes in accordance with Oregon Administrative Rules 814-23-900 through 814-23-909. The Canadian
Comfort Industries pellet stove has been independently tested and listed by INTERTEK (an accredited testing
laboratory) to UL, ULC and CSA standards. It is tested and listed for residential installation according to current
national and local building codes as:
 A Freestanding Room Heater
 A Mobile Home Heater.
 Fireplace Insert
 Built-in Insert
 A Hearth Stove
The Safety Listing Label is located on the rear
inspection panel for model FPP, and on the
hopper panel for model IPP. Please read the
label carefully. It contains important information
about installation and operation of your
pellet appliance.
Note: Your STOVE’S serial number is located
on the safety label. Your appliance serial number
is preceded by a “WH-“ (example WH-00000).
(see diagram)
PelPro Appliances www.pelprostoves.com 5
DONOTREMOVE ORCOVERTHISLABEL
LISTED PELLET BUR NING ROOM HEATER/FIREPLACE INSERT POÊLE HOMOLOGUÉ AUTONOM E/ E NCAS TRAB LE À COMBUSTIBLES SOLI DES CONV ENA N T
ALSO FOR USE I N MOB I LE HOMES ÉGALEM ENT POUR INSTALLATION DANS LES MAISONS MOBILES.
CCI MODELS:/MODÈLES: [ ] FGB [ ] IGB [ ] FPP [ ] IPP OP TIO NS: CCI-I-3HZ & CCI 1-3VL BUILT IN FIR EPLACE KIT S / CON STRUIT DANS DE S KITS DE CHEMINEE
OPTIONS: CCI-MFBG MULTI-FUEL BURN GR ATE / CCI-MFBG
TESTED PER UL 1482-00, ASTM E 1509-04, ULC S627-00, ULC S628-M93,
THIS PELLET BURNING APPLIANCE HAS BEEN TESTED AND LISTED FOR USE IN MANUFACTURED HOMES IN
ACCORDANCE WITH OREGON ADMINISTRATIVE R ULES 814-23-900 THROUGH 814-23-909.
A
B
UNIT
UNIT
CUNIT
FLOOR
PROTECTOR
E
B
B
AD
F
BBA
B
UNIT
ALCOVE
B
B
INSTALL AND USE ONLY IN AC CO R DANCE WIT H MANUFACT URER’S INSTALLATIO N AN D OP ERATING INSTR UCTI ONS.
------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- -----
CONTACT LOCAL BUILDING OR FIR E OFF ICI ALS T O OBTAIN A PERMIT AND INFORMATIO N ON ANY INSTALLATI ON
REQUIREMENT S A ND INSTALLATI ON INSPECTIO N IN YOUR AR EA.
------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- --- ---
WARNING: DO NOT INSTALL APPLIANCE IN A SLEEPING ROOM.
------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- -----
FOR USE WITH 1/4. (6 MM) – 3/8’ (10MM) PELLETIZED WOOD FUEL.
MAX. INPUT RATING APPROXIMATELY 4.5 – 5 LB.’S PER HOUR USING 8,500 - 8,770 BTU/LB OF PELLET FUEL
ALSO FOR USE WITH SHELLED CORN AND WHEAT, UNDER 14% MOISTURE, USING MULTI-FUEL GRATE SYSTEM
MAX. INPUT RATING APPROXIMATELY 6.5 – 7 LB.’S PER HOUR
USE OF OTHE R F UEL MAY DAMAGE UNIT AND C AUSE A HAZAR DO US C ONDITION.
------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- -- --
INSTALL ON A NON-COMSUSTIBLE FLOOR PROTECTOR EXTENDING UNDER THE APPLIANCE AND 6 IN (152.4 MM)
BEYOND THE FRONT AND 6 IN (152 MM) TO EACH S I DE. DO NOT OBSTRUC T SPACE UNDER UNIT.
------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- --- ---
INSTALL AND USE ONLY IN A CODE COMPLY IN G MASONRY OR LI S TED FACTORY- BUILT FIR E PLAC E. DO NOT
REMOVE BRICKS OR MORTAR FROM MASONRY FIREPLACE, USE A NON-COMBUSTIBLE FLOOR PROTECTOR
EXTENDING BENEATH AND 6 INCHES TO THE FRONT OF THE UNIT. MUST ALSO INCLUDE A CHIMNEY LINER MEETING
TYPE HT REQUIREMENTS (2100 F) PER UL1777(US) OR ULC 8635 (CND).
------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ----- --
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE
------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ----- --
VENTING SYSTEM: TYPE PL. VENTING SYSTEM MUST BE USED. CLEARANCES FROM THE P L VENT ARE AS PER THE
VENT SYS TEM MA NUFACTURER’S I NST R UCTIONS. SEE LOCAL BUILD ING CODE AND APPLIA N CE AND VEN T
MANUFACTURER’S INS TRUCTIONS FO R P RECAUTIONS REQUIRED FOR PA SS IN G VENT ING SYSTEM THR OUGH A
COMBUSTIBLE WALL OR CEILING.
------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- -----
UNDER CERTA IN CONDITIONS OF USE, CREOSOTE BUILDUP MAY OCC UR RAP IDLY. INS PE CT AND CLEAN VENTI NG
SYSTEM FREQUENTLY.
------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- --- ---
KEEP VIEWING, AS H REMOVAL AND HOPPER DOORS TIGHTLY CLOSED DUR I NG O PER ATION.
REPLACE GLASS WITH CERAMIC GLASS ONLY.
------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- -----
RATING: 120 VOLTS 2.0 AMPS 475 WATTS 60 HZ. ROUTE POWER SUPP LY CORD AWAY FROM UNIT.
------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- -----
LIGHTING/SHU TDOWN INSTRUCTIONS : PLACE SMALL AMOUNT OF PELLETS IN GRATE-PLACE PROPRIETORY FIRE
STAR TER ON P E LLET S - P RES S ON T OUCH PAD - LI GHT - CLOS E DO OR . SELECT FEED RATE AND FAN SPEED.
TO SHUT DOWN; PRESS OFF TOUCH PAD. REFER TO OPERATORS MANUAL, FOR ADDITIO NAL DE TAILS.
------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ----- ----- ---- ------- ----- ----- ----- ----- ----- ------
CAUTION: MOVING PARTS MAY CAUSE INJURY. DO NOT OPERATE WITH PANEL OPEN.
DANGER: RISK OF ELECTRIC SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT.
WARNING: HOT PARTS DO NOT OPERATE WITH SIDE PANELS OPEN.
MANUFACTURED BY: DATE OF MFG. / DATE OF FABRICATION
DANSONS INC. EDMONTON, AB, CANADA
1-877-303-3134
TESTÉ PAR UL 1482-00, ASTM E 1509-04, ULC- 627-00, ULC-S628-M93,
POUR L' CU TILIS ATI ON DANS LES MAISONS MANUF ACTURÉ ES SELON DES RÈG LES ADMINISTRATIV E S DE L'C
ORÉGON 814-23-900 À 814-23-909
MINIMUM CLEARANCES TO COMBUSTIBLES / MINIMUM DE DÉGAGEMENTS JUSQU’A L A COMBUSTIBLE
A. 2 IN/PO, (50 MM) D. 16 IN/PO, (406.4 MM)
B. 6 IN/PO, (152.5 MM) E. 2 IN/PO, (50 MM )
C. 2 IN/PO, (50 MM) F. 48.5 IN/PO, (1250 MM )
BUILT IN INSTALLATION : (REQUIRES ACI-3H2 OR ACI-3VL BUILT IN KITS) SEE INSTALLATION MANUAL FOR DETAIL.
FR AMING OP ENIN G: CLEAR ANCES :
HEIGHT = 26 ” SIDE & R E AR S TAND-O FF S TO FR AMING = 0”
WIDT H = 38” HOP P E R TOP TO FRAMI NG = 1”
DEP TH = 24”
INSTALLEZ SELON ET UTILISEZ SEULEMENT L'CINSTALLATION DE MANUFACTURER.S ET LES C ONSIGNES
D'UT ILI S ATION. LES FONCTI ON NAI R ES LOCAUX ENTREZ EN CONTACT AVE C BÂ TIMENT O U FEU AU SUJ ET
DES R ESTR I CTIONS ET INS P E CTION D'CIN S TALLATION DANS VOTR E Z ONE.
________________________________________________________________________________________
AVERTIR N'INSTALLENT PAS L'CAPPAR EIL DANS UNE SALLE DE SOMMEIL. POUR L'CUSAGE ONLV AVEC 1/4.
(6 MM). 3/8. (10MM) CAR BUR ANT E N B OIS PE LLETISÉ. L' UTILISATI ON De L' AUTRE CARBURANT P E UT END
OMMAGER L'UNITÉ ET CAUSER UN ÉTAT DANGER E UX.
ENTRÉE ÉVALUANT 8,500 – 8,770 BTU/LB DE CARBURANT DE GRANULE.
_________________________________________________________________________________________
INSTALLEZ SUR UN PROTECTEUR DE PLANCHER DE NON-COMSUSTIBLE ÉTENDANT SOUS L'CAPPAREIL ET LES
6 DEDANS (152.4 MILLIMÈTRE) AU DELÀ DE L'CAVANT. N'O BS TRUEZ PAS L' CESPACE SOUS L'CUNITÉ. INSTALL EZ
ET U TILISEZ SEU LEME NT DANS UNE MAÇO NNERIE D'CACQU IESCEM EN T DE CODE OU UNE CHEMI NÉ E CONS TRUITE
PAR USINE ÉNUMÉR ÉE. NE RET IREZ PAS LES BRIQUES O U LE MOR TIER DE L'CUT ILIS ATION DE CHEMI NÉE DE
MAÇONNERIE UN PROTECTEUR NON-COMBUSTIBLE DE PLANCHER ÉTENDANT DESSOUS ET 6 POUCES À L 'CAVAN
T DE L'CUNITÉ.
NE RELIEZ PAS CETTE UNITÉ À UNE CONDUITE DE
CHEMINÉE DE CHEMINÉE SERVANT UN AUTRE APPAREIL
CIR CUIT DE MIS E À L'AIR LIBRE: UN CI R CUIT DE MISE À L'AIR LIB R E DE P L. DE TYPE DOIT ÊTR E UTI LISÉ. LES DÉGAGE-
MENTS AVEC L'CÉVENT DE PL SONT SELON LES I NST R UCTIONS DU CIRC UIT DE M ISE À L'AIR LIBR E MANUFAC TUR ER.S.
VOIR LE BÂTIMENT LOCAL CODER ET LES INSTR UCTIO NS D' CAP PAREIL ET D'CÉ V ENT MANUFACTUR ER. S POUR DE S
PRÉCAU T IONS REQUIS E S P OUR PASSER LE CIR CUIT DE MIS E À L'AIR LIB R E PAR UN MUR OU UN PLAFO ND
COMBUSTIBLE.
DANS CE RTAINES CONDI TIONS D'C UT IL ISATION, L' CH ABILLAGE DE CRÉOSOTE PEUT SE P RO DUIRE R API DEMENT.
EXAMINEZ ET NETTOYEZ LE CIRCUIT DE MISE À L'AIR LIBRE FRECUENTLY.
_________________________________________________________________________________________
ACTIONNEZ L'CUNITÉ SEULEMENT AVEC DES P ORTES ENTIÈREMENT FERMÉES REMPLACENT LE VERRE PAR LE
VERRE EN CÉRAMIQUE SEULEMENT. ESTIMATION: 120 VOLTS 2, 0 AMPÈRES 60 HERTZ . CORDE D'CALIMENATION
D'CÉ NE RGIE D' CILT INÉRAIRE LOIN À PARTIR D' CUNI TÉ. INSTRUCTIONS DE LI GHTING/SHUTD O WN: P LACEZ UN
PEU DE GRANULES S UR LA GR ILLE - P LAC EZ LE DÉMAR R EUR DU FEU DE PR OPRIETO RY SUR DES GRANULES –
METTENT LE COMMUTATEUR "CMARCHE/CARRÊT" EN MARCHE - LUMIÈRE - À LA PORTE ÉTROITE. TOURNEZ LE
COMMUTATEUR DE CARBUR ANT AU BAS. POUR S'ARRÊTER, COMMUTATEUR " CMARCHE/ CARRÊT " DE TOUR
POUR SE RAPPORTER HORS FONCTION AU MANUEL D'COPÉRATEURS, POUR LES DÉTAILS SUPPLÉMENTAIRES.
AVERTISSENT: LES PIÈCES MOBILES PEUVENT CAUSER DES DOMMAGES. NE
FONCTIONNEZ PAS AVEC LE PANNEAU OUVERT.
DANGER: RISQUE DE DÉCHARGE ÉLECTRIQUE. DÉBRANCHEZ LA PUISSANCE
AVANT UNITÉ D'CENTRETIEN.
AVERTISSEMENT: LES PIÈCES CHAUDES NE FONCTIONNENT PAS AVEC LE PANNEAU
OUVERT.
FABRIQUE PAR:
INDUSTRIES CANADIENNES DE CONFORT; EDMONTON, AB, CANADA
VAILLEZ À NE PAS ENLEVER NI À DISSIMULER CE COLLANT

6
H
HOW
OW
Y YOUR
OUR
A APPLIANCE
PPLIANCE
W WORKS
ORKS
Cautions:
Do not try to operate your stove with viewing door open. Pellets will not feed under these
circumstances and a safety concern may arise from sparks or fumes entering room.
If you are not drawing combustion air from outside, care must be taken to allow for adequate air
make up, to avoid possible room air starvation when stove or other exhaust fans are in
operation.
It is highly recommended that you install a high quality smoke detector as well as a carbon
monoxide gas detector in the room where stove is installed. Care should be taken to make
sure detectors are in working order at all times.
Fuel in the form of wood pellets or is stored in the hopper. An auger delivers the
pellets to the burn grate. The fuel rate, or heat output, is set by adjusting the feed
rate touch pad, (settings 1 to 4). A fan provides combustion air to the burn grate.
The amount of combustion air in the burn grate is adjustable and automatically
changes as the fuel rate changes. The higher the fuel rate, the larger the amount
of combustion air and visa versa. The fuel burns in the burn grate, producing
heat. Some heat radiates out the front of your stove. The majority of the heat
passes around the heat exchange tubes and air plenum around the firebox and is
then moved into the room by the room air fan. A small amount of heat must pass
out the exhaust of your stove, along with gases, into the atmosphere.
Your stove's heat output can be adjusted from setting 1-4, through the FEED
RATE touch pad, to vary your heat output from Low to High. The room air fan can
be manually adjusted through the FAN SPEED to run faster or slower to corre-
spond to the amount of heat being produced. The room air fan is also on a limit
switch, controlled to run on high when the stove reaches higher temperatures and
then resume the speed you had selected once it cools to a lower temperature.
Your stove can run efficiently over
extended periods of time and at dif-
ferent heat output levels as long as
the fuel supply is uninterrupted and
timely cleaning and maintenance
is preformed. An example of how
improper cleaning effects operations
is; the exhaust pressure switch will
shut the pellet supply off and your
stove will shut off if the exhaust sys-
tem becomes plugged.
The operations and maintenance of your PelPro Series of multi-fuel appliance are unique and should not
be considered to be like a wood, coal, gas, electric, propane or oil heater, stove or appliance.
FUEL CONSIDERATIONS
Your PelPro Series of Multi-fuel appliance is designed to burn the following:
1. Wood pellets that comply with the Pellet Fuel Industries standards.
2. A combination of up to 50/50 Wood Pellet and Shelled Corn
PelPro Appliances www.pelprostoves.com 6
as desiredas desired
Memory &
Fan Trim
Hopper
Auger
Auger Motor
Fan Motors
Exhaust
Air Intake
Ash Pan
“Super Grate”
Burn Pot
Window
Tube Scraper
Heat Exchange
Tubes
Auger Cover

7
A
AUTOMATIC
UTOMATIC
S SAFETY
AFETY
F FEATURES
EATURES
L120 LOW LIMIT SWITCH
This limit switch is mounted on the exhaust blower housing and has 2 main functions:
Should the fire happen to go out, for any reason, this limit switch will shut the stove off when the exhaust
temperature drops below 120° F.
Upon starting the appliance, the AcuTron control board has a 15 minute “Lighting Mode”, if the stove
exhaust does not reach 120° F in that 15 minutes the stove will shut off. As soon as the stove
exhaust does reach 120° F, the limit switch opens and the AcuTron enters a 5 minute “Safety Delay”
mode.
F140 FAN LIMIT SWITCH
Your pellet appliance has a convection fan control limit switch. The room air fan's (F140) temperature limit
snap switch automatically operates the fan on high when your stove is producing heat faster than the fan is
carrying it into the room. This may occur when the heat control lever is set at [3 or 4] and the FAN SPEED is
set to a very low or off setting. After the fan runs at this automatic high setting a few minutes, it may cycle back
to its lower setting and may continue to cycle between [HIGH] and your selected setting. The circulation (room
air) fan cycling from high to low is a normal condition as well as a safety feature of your appliance.
To compensate for the fan cycling, adjust the FAN SPEED to a higher setting.
L250 HIGH LIMIT SWITCH
Your pellet appliance has a high temperature limit switch installed. If the temperature at the back of the firebox
reaches approximately 250° F., the switch will shut off the electricity going to the Vacuum Switch and to the
Auger Motor. The auger will automatically stop, and the appliance will shut down when the exhaust
temperature cools (120° F). If this happens call your dealer or Dansons Customer Service (1-866-456-9269).
IT IS IMPORTANT TO FIND THE REASON WHY THE UNIT OVERHEATED.
VACUUM SWITCH
This safety device (mounted on the back panel pillar) detects vacuum in the exhaust system, firebox, and air
intake. If the exhaust blower fails, the vent pipe becomes plugged, the viewing door is open, or if you are out
of pellets, this switch will sense that there is a lack of vacuum and will stop the auger from continuing to feed
pellets.
HOPPER LID SWITCH
This device is mounted inside the
hopper. and is connected to the
auger feed system.……
If the hopper lid is OPEN the switch
WILL STOP THE AUGER FEED
SYSTEM. This is to prevent fingers,
clothing or other objects from
coming in contact with the auger.
The auger is capable of causing
serious injury and this switch
MAY NOT be disconnected.
AcuTron Wiring Harness
Air Intake
Vacuum Switch
Low Limit L120
High Limit L250
Fan Limit F140
Combustion Fan
Exhaust
PelPro Appliances www.pelprostoves.com 7
Left Hand Side View
/ Exhaust Fan Side
If the power does go out, the pellet appliance will stop running. When the power comes back
on, the stove will remember the function it was performing and return to that function.

8
S
SPECIFICATIONS
PECIFICATIONS
PelPro Appliances www.pelprostoves.com 8
HEATING SPECIFICATIONS
DIMENSIONS
ELECTRICAL SPECIFICATIONS
Electrical Rating = 115 Volts 60 HZ 2.0 Amps
Watts (operational) = 175 (approximately)
Watts (optional igniter) = 475 (approximately)
A voltage surge protector or ground fault outlet is required for this unit. The warranty on the circuit
board will be voided if surge protection is not installed before operating this unit.
If power outages or disturbances are a concern, you may wish to purchase a gas powered generator,
solar or battery back-up system. Ensure that it is a “Positive” sign wave and a minimum 1000 watts
continual, as well as surge protection.
EPA COMPLIANCE
This heater is exempt from EPA Phase II requirements, but has been tested for emissions using EPA test
methods by Warnock Hersey , US. Pellet appliances that are designed with the combustion air supply
exceeding 35:1 (by ratio) are exempt from EPA regulations.
¹ Heating capacity will vary depending on floor plan layout of your home, degree of insulation, and
the outside temperature. Fuel size, quality, density and moisture level will also have an effect.
¹¹ Pellet size may affect the actual rate of fuel feed and burn times. Fuel feed rates may vary by as
much as 20%. Use PFI listed fuel for best results, pelletheat.org for further information.
24”
28 3/4”
24”
183/4”
+
+
Shroud 1”
+
+
24”
6 1/2”
7 3/4”
8 1/4”
3 ½”
Exhaust
Air I nlet
8 1/4”
Air Inlet
17 1/4”
12 3/4”
6 1/2”
Exhaust
24 3/4”
24”
24 3/4”
12 1/4” 10 3/4”
+
+
24”
8 1/4”
Air Inlet
17 1/4”
12 3/4”
6 1/2”
Exhaust
24 3/4”
30”
24”
+
Shroud1”
8 1/4”
Air In let
17”
12 3/4”
Exhaust
26”
12 1/4” 10 3/4”
+
25”
Air In let
7”
Exhaust
++Exhaust
26”
+
24”
6 ½”
Exhaust
+
Air Inlet 8 1/4”
7 3/4”
3 ½”
24”
Bay View Freestanding Bay View Insert / Built-In
Traditional Freestanding Traditional Insert / Built-In
19”
-
23”
Adjustable
Hopper
Approx. Heating capacity (sq. feet) * 800 – 2,000
Approx. Fuel burn rate per hour ** 1.5 – 5 lbs
Hopper Capacity - Traditional Stove / Insert 40 lbs Approx. Burn time at lowest setting 27 hrs
Hopper Capacity – Bay View Free Standing 60 lbs Approx. Burn time at lowest setting 48 hrs
Hopper Capacity – Bay View Insert / Built-In 40-60 lbs Approx. Burn time at lowest setting 27-48
Product is subject to change without notice.

9
P
PLANNING
LANNING
&I &INSTALLATION
NSTALLATION
C CHECK
HECK
L LIST
IST
Unless you are knowledgeable and experienced in stove installation, we recommend your PelPro Appliance
receive a Pre-delivery Check and be installed by your local Specialty Retailer, NFI (National Fireplace Institute)
Pellet Specialist (USA) or WETT Certified Installer (CAN) .
COMPLETE THIS CHECK LIST PRIOR TO INSTALLING YOUR MULTI-FUEL APPLIANCE:
_____ Carefully read this "Owners Manual”. SAVE THIS MANUAL.
_____ Have your local Dealer demonstrate all the operational, cleaning and maintenance steps
necessary for your stove.
_____ Select a location. The design of your home and the stove placement will determine its value
as a source of heat. A pellet appliance depends primarily on air circulation to disperse its
heat. There are other practical considerations, which must be considered before a final
placement is decided on:
Existing Chimneys, Pellet Fuel Storage, Aesthetic Considerations, Roof Design (rafter
locations & roof pitch), Room Traffic, Clearances to Combustibles, and Existing Wiring.
_____ The installation of this appliance must conform to local codes and applicable state and
federal requirements. Becoming familiar with these requirements before installation is es-
sential.
______ Attach your proof of purchase to this manual and keep on hand for warranty.
COMPLETE THIS CHECK LIST WHILE INSTALLING YOUR MULT—FUEL APPLIANCE:
_____ Carefully read the ENTIRE installation section first. Twice is better.
_____ Read the Installing Freestanding, Insert or Built-In sections.
_____ Determine the location and measurement needed your chosen location.
_____ Be sure to pre-fit all items before you install, fasten or install the stove permanently.
Remember measure twice, cut once.
_____ Ensure ALL joints of “PL” vent and single wall stainless steel liner are tightly connected,
sealed with RTV Silicone or Hi-Temp foil tape, including to the exhaust connector, and
is correctly installed. (Follow vent manufacturer’s instructions.)
COMPLETE THIS CHECK LIST PRIOR TO LIGHTING YOUR FIRST FIRE:
_____ Obtain final inspection and approval by local building officials.
_____ Carefully clean all marks off the brass, nickel or pewter parts before the first fire is lit. Use a
soft cloth and a gentle type cleaner. Caution: Never use an abrasive cleaner on any part of your
stove.
_____ Polish the hopper to remove the oil type coating used in manufacturing.
_____ The high temp. stove paint used on your stove may take several hours of burning at a high fuel
setting to fully cure. During this time an odor, which is not harmful, may be evident. The area
around the stove should be well ventilated.
_____ Review and follow the Lighting and Controls Instructions.
_____ Ensure that appliance is connected to a surge protection unit.
_____ Fill the hopper with quality pellets, Close the Hopper Lid Using the CCI “AcuTron”, (figure 5),
PUSH the FEED RATE Touch Pad and this will start the auger and the combustion fan.
PelPro Appliances www.pelprostoves.com 9

10
P
PLANNING
LANNING—
—E EXHAUST
XHAUST
S SYSTEMS
YSTEMS
PELLET VENT MUST MAINTAIN A MINIMUM 3” CLEARANCE TO ANY COMBUSTIBLE
(INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER).
DO NOT CONNECT THE PELLET VENT TO A VENT SERVING ANY OTHER APPLIANCE OR
STOVE.
DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.
PELLET VENT TYPE:
1. Must be an approved 3” or 4” Diameter Type ”PL” vent, vented to the outside (fig. 7) or connect
the vent to a factory built type “A” chimney using an adaptor.
2. Exception: A single wall “All Fuel” Stainless Steel chimney liner may be used inside a fireplace
or fireplace installations (fig. 8) .
3. Some venting manufactures do make “PL” vent for use with wood pellet fuel only and another
type of “PL” vent for corn or bio mass fuels. If in doubt, plan for the future and use the corn or
multi-fuel
4. Use 4” dia. vent if vent or liner height is over 15’ or if installation is over 3.000’ above sea level.
NOTE: 4” diameter vent may be used in all installations. If in doubt, use 4” dia. vent.
VENT SAFETY PRECAUTIONS:
A “Clean Out Tee” (4) must be installed at the bottom of all vertical runs. These “Tee’s” are to assist in
periodically cleaning the vent. Single or Double clean out tees may be used. The exhaust system must
be installed so the entire system can be cleaned without disassembly.
Termination must exhaust above the fresh air inlet
elevation, and parallel or above the exhaust output
of the multi-fuel appliance.
It is highly recommended that at least 3 feet of vertical
pipe (5) be installed to create some natural draft. This is
to help prevent the possibility of smoke or odor during
the appliance shut down.
Horizontal sections must have a 1/4” rise every 12” of
travel after 3’ long.
Pellet vent connections must be sealed gas tight. Use
Hi-Temp RTV Silicone, good for over 600° F or Hi-temp
Metal foil tape, that meets UL181 standards,. DO NOT
use “Duct Tape”.
Seal each vent section by injecting a liberal amount of
sealant into the gap and/or wrap with foil tape.
It is strongly recommended that the exhaust system
be terminated on the prevailing wind side of the home.
Appliance may not be placed in, or vented through
a gas fireplace.
1
23
4
5
6
78
9
PelPro Appliances www.pelprostoves.com 10

11
P
PLANNING
LANNING—
— E EXHAUST
XHAUST
S SYSTEMS
YSTEMS
…
… CONTINUED
CONTINUED
DETERMINE VENTING SIZE AND DISTANCE:
It is recommended that the vent system be installed with a minimum of three (3’) of vertical
rise above the appliance exhaust port.
Equivalent Vent Length (EVL) is the method of determining vent sizes and lengths, that takes into account the
effect of different component parts on air flow.
STEP 1 To help you determine the correct size and/or run, simply fill in the chart below.
Pellet Venting
Component # of Elbows OR feet of Pipe Multiply by Equivalent Feet Component Equivalent
90 Degree or Tee X 5
45 Degree X 3
Horizontal Pipe X 1
Vertical Pipe X .5
Total Equivalent
Step 2 Ensure the Total Equivalent is or is
less than 30.
Step 3 Use the Sizing Chart to determine
the proper venting size according to
the Total Equivalent and the
Altitude above sea level.
NOTE: In some cases it may be necessary
to contact Dansons Customer
Service personal to determine
acceptable venting
configurations
and altitude adjustments
1-877-303-3134.
The diagram to the right will help to
give you a visual reference.
0 1 2 3 4 5 6 7 8 9 10
10
20
30
Altitud e in Thousa nd s of Fe e t
EquivalentPipeLengthinFeet
3 or4 Inch DiameterPipe
4 InchDiameterOnly
Use Diameter “PL” Vent
If venting outside of
shaded area.
4”
0’
0’
5’
5’
10’
10’
15’
20’
25’
30’
33’
Vent must have a support
bracket every 5’ when on
the exterior wall.
Vent height and run
exceed the distance
shown in the un-shaded
region of chart.
must
not
To achieve optimum
performance, keep vent runs
as short as possible.
Especially on horizontal
installations.
Use or Diameter
“PL” Vent, if venting in
shaded area.
3” 4”
Maximum venting height is 33’.
Maximum horizontal offset is 10’.
Use the Equivalent Vent Length
Chart to determine proper
combination of component parts.
PelPro Appliances www.pelprostoves.com 11

12
P
PLANNING
LANNING—
— E EXHAUST
XHAUST
S SYSTEMS
YSTEMS
…
… CONTINUED
CONTINUED
PELLET VENT TERMINATION: (Figures 7 & 8)
Termination must be a minimum of 12” above the chase cap (B) (note: the chimney must meet
local codes for height above the roof or other obstructions)
Must have an approved cap (G) (to prevent water
from entering) or a 45* elbow downturn (F)
If the termination is located on a windy side of
house, an approved house shield is recommended
to prevent soot from accumulating on the side of the
house.
Must not be located where snow or other materials
such as leafs, snow or grass, could block it.
Must have a “Metal Seal Plate” or “Wall Thimble” at
point (A)
Figure 7 Figure 8
VENT TERMINATION CLEARANCES:
NOTE: Horizontal terminations must protrude 12” from the wall, vertical terminations 24”
A Minimum 4’ clearance below or beside any door or window which opens.
B Minimum 1’ clearance above any door or window that opens.
C Minimum 3’ clearance from any adjacent building.
D Minimum 7’ clearance above any grade when adjacent to public walkways.
E Minimum 2’ clearance above any grass, plants, or other combustible material.
Minimum 1’ clearance above grade.
F Minimum 3’ clearance above any forced air intake of any other appliance within 6’.
G Minimum 2’ clearance below eves or overhang.
H Minimum 1’ clearance horizontally from combustible wall.
I Minimum 1’ clearance to inside corner
X Must be a minimum of 36” above the roof and 24” above the highest point of the roof within 10’.
NOTE: The following are not found on the above diagram.
 Minimum 3’ above a gas meter/regulator within 3’ horizontally of the vertical centre line of regulator.
 Minimum 6’ clearance to a gas service regulator vent outlet.
 Minimum 1’ clearance under veranda, porch, deck or balcony. Permitted only if structure is fully open on
a minimum of two sides beneath the floor.
A
B
A
B
3’
10’
2’
x
Inside Corner
Detail
I
E
PelPro Appliances www.pelprostoves.com 12

13
P
PLANNING
LANNING—
— O OUTSIDE
UTSIDE
A AIR
IR
Outside air is REQUIRED ON ALL MOBILE HOME INSTALLATIONS.
Outside air is strongly recommended for all other installations. Failure to install intake
air may result in improper combustion as well as the unit smoking during power failures.
Metal pipe, ONLY, either solid or flexible, must be used in all outside air installations.(B)
NOTE: Non-metallic material, such as PVC or ABS plastic piping,
MUST NOT BE USED for outside air installations.
A wind shield, (C), over the termination of the outside air pipe or a 90 degree elbow or
bend directed away from the prevailing winds MUST be used when an outside air pipe
is in-stalled through the side of a building. Keep the outside air pipe termination at least
1 foot away from the exhaust system termination.
When outside air is taken from an existing chimney, the exhaust system must not
terminate in the same chimney.
The outside air pipe on your stove is 2" OD. The outside air connecting pipe must be at
least 2" ID The outside air connecting pipe must be as short and free of elbows as
possible, and must fit over, (A), not inside, the outside air pipe on your stove.
For distances over 10’ long, 3” or 4” OD pipe is recommended, then reduce to 2”.
Through The Wall Kits Include:
3 FOOT PACKAGE – PART# KS5150-1450 10 FOOT PACKAGE – PART# KS5150-1460
1 – 2” Galvanized Hood c/w screen 1 – 2” Galvanized Hood c/w screen
1 – 2” Aluminum Flex Duct – 1 – 2” Aluminum Flex Duct –
compressed 15” length, extends to 30” – 36” compressed 4’ length, extends to 120”
2 – 2” Worm Gear Clamps 2 – 2” Worm Gear Clamps
NOTE: Available from your local Authorized
Dealer or Dansons Inc. 1-877-303-3134
Figure 11
PelPro Appliances www.pelprostoves.com 13

14
P
PLANNING
LANNING—
— P PROTECTION
ROTECTION
&C &CLEARANCES
LEARANCES
STOVE PLACEMENT:
FLOOR PROTECTION REQUIREMENTS:
MINIMUM CLEARANCES TO COMBUSTIBLES: Figure 10—15
NOTE: Although not required for safety reasons, it is strongly suggested that sufficient space be provided
(a minimum of 24”) on each side of the appliance and at the back of the appliance to enable servicing the unit
if necessary. If this space is unavailable, a provision must be made to enable sliding the appliance out.
CLEARANCES – “STRAIGHT INSTALLATION”:
Stove must be placed so that no combustibles are within, or can swing within (i.e. drapes doors),
36” of the heater.
Keep in mind the following placement concerns; venting obstructions, outside air, electrical
outlet, wall thermostat, heat distribution, traffic patterns and room use/size.
If the stove is placed in a location where the ceiling height is less than 7’, it must follow the
requirements in the section “Alcove Installation”.
2” From Back Of Stove to Combustibles 3” From PL Vent to Combustibles
2” From Side of Stove to Combustibles 6” Non Combustible Surface on side of Heater
2” From Back Corner of Stove to Combustibles 6” Non Combustible Surface In Front of Heater
16” From Top Of Stove to Combustibles 36” to drapes, doors, anything that can swing
PelPro Appliances www.pelprostoves.com 14
Stove and floor protection must be installed on a level secure floor
NOTE: It is important for your appliance to be level. Leveling should occur below the floor
protection pad.
The stove must be installed on a continuous (grouted joints) non-combustible floor protector
such as ceramic tile, cement board, brick, 3/8” millboard or equivalent, or other approved or
listed material suited for floor protection.
THE MATERIAL(S) USED MUST HAVE, OR COMBINE TO HAVE, A MINIMUM INSULATIVE
RATING OF “R1”.
Must extend 6in (300mm) beyond the front of the stove as well as 6 in (300mm) beyond each
side of the fuel loading and ash removal opening(s)
Must extend under and 2” to each side of chimney tee (if used).
6”
1”
10”
6”
2”
12”
HROUGH HE ALL T T
W
6”
3”
NTERIOR ERTICAL I
V
6” 6” 6” 6”

15
P
PLANNING
LANNING—
— P PROTECTION
ROTECTION
&C &CLEARANCES
LEARANCES
...C
...CON
ON’
’T
T
CLEARANCES – “CORNER INSTALLATION”:
Figure 12 Figure 13
Note: If interior vertical vent is used (figure 13), the clearance to the back wall is determined by the
upward-turned “Clean Out Tee”. It will vary in depth depending on the brand of PL vent used.
Before placing the stove, connect the “Tee” and measure off the 3” clearance.
ALCOVE INSTALLATION:
Minimum clearances to combustibles: (Figure 14 & 15)
1 inch from back of appliance 6 inches from the sides
16 inches from the top 30 inches deep
Figure 14 Figure 15
16”
PelPro Appliances www.pelprostoves.com 15
6”
1”
10”
6”
2”
12”
LCOVE HROUGH HE ALL A -T TW
6”6”
2”
12”
6”
HROUGH HE ALL T TW
ORNER 45 C
3”
6”
NTERIOR
ERTICAL
I
V
ORNER 45 C
6”
6”
6”6”

16
T
TOOLS
OOLS
R REQUIRED
EQUIRED
Power Tools
Shop Vacuum WITH Filter
Jigsaw or Reciprocating saw
Electric drill
Extension cord
4” or 5” diameter coring bit and drill
(if going through concrete)
Hand Tools
Tape Measure
Caulking Gun
Circle Maker
Allen (Key) wrench set
Stud Finder
Set of sockets or nut driver 1/4”, 5/16” and
7/16”
Assortment of Phillip, Robertson and slot
screwdrivers
Assortment of sheet and wood drill bits
Flashlight
Wire stripper and wire cutter
Hammer
Bubble Level
Utility knife
Adjustable pliers (6 to 8 inches)
Small hand broom and dustpan
Furniture and Floor Protection
Supplies
Caulking tube of RTV Hi-Heat Silicone
2” long Wood screws (10+)
Assortment of sheet and wood screws
“Stove Bright” Hi-Heat Stove Paint
Caulking tube of Clear Silicone
Hi–Heat Aluminum Foil Tape
Before starting your PelPro Multi-Fuel install, we recommended you have the following list of tools ready. This
is not an exhaustive list, but should go along way in making your installation easier.
PelPro Appliances www.pelprostoves.com 16

17
I
INSTALLATION
NSTALLATION—
—F FREESTANDING
REESTANDING
THROUGH THE WALL, DIRECT VENT INSTALLATION. (not preferred) (Figure 18)
1. Select the location for your stove, design the
exhaust system and determine the brand and
size of "PL" vent to be used.
2. Position the floor pad.
3. Following the "PL" vent manufacturer's specifi-
cations, mark and cut a hole through the wall to
accommodate the wall thimble, (F), and the out-
side air pipe, (I), if outside air is to be used. Re-
member that the outside air intake must be lo-
cated no closer than 12” from the vent exhaust.
Try to avoid cutting wall studs, and use extreme
caution to avoid cutting into power or water lines
within the wall of your home.
4. Install the wall thimble, (F). Be sure to run a bead
of silicone around the outside edges of the wall
thimble to reduce drafts, both inside and outside.
Insert the proper size of "PL" vent, (E), through
the wall thimble, (F).
5. Place your stove on the floor pad, close to its
final position. Leave room to connect the "PL" vent to “Quick Connect” end collar. If not already factory
installed, Install the gasket (B) and “Quick Connect” exhaust end (C) to your stove to the “Quick Connect”
mounting plate. Use the 4 x 7/16” nuts, supplied and secure tightly.
6. Place a bead of RTV silicone around the end collar of the “Quick Connect” of your stove's exhaust, (C).
Firmly push the “PL” vent pipe adaptor (J) into the bead of RTV silicone.
Note: If 4" PL vent is required, use an 3” to 4” Pipe Adaptor Increaser, (J), on the stove exhaust pipe.
7. Connect the length of "PL" vent, (E), that is in the thimble, (F), onto the pipe adaptor (D). Fasten
together with at least three sheet metal screws (approx. 3/8” in length). Place a bead of RTV silicone
around the connection.
8. Place your stove in its final position on the pad. Place another bead of RTV silicone around the “PL”
vent (E) and the inside of the wall thimble, to stop cold air drafts.
9. On the outside of the building, place an exhaust cap (G) or a 45 degree "PL" type elbow, (G), onto the
end of the horizontal "PL" vent, (E). Optionally, place a rodent screen cap, (G), (may be required in
some locals), on the end of the elbow, (G). run a bead of RTV silicone around all connections and
around the “PL” vent pipe and the outside of the wall thimble.
Note: The end of the exhaust pipe must extend a minimum of 12” from the outside of the building.
Note: Most horizontal, through the wall installations may require a Clean-out Tee and minimum 3’
vertical rise of pipe, inside or outside the building. See Next Page.
PelPro Appliances www.pelprostoves.com 17
6”
1”
10”
6”
2”
12”
HROUGH HE ALL T TW
6” 6”

18
M
MOBILE
OBILE
H HOME
OME
I INSTALLATION
NSTALLATION
CAUTION: DO NOT INSTALL STOVE IN SLEEPING ROOM
THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR,
CEILING and ROOF MUST BE MAINTAINED!
Your PelPro Series appliance has been tested and listed for mobile home installation. It may be
installed in a mobile home as a "Free Standing Stove" or a "Hearth Stove", see detailed install and
clearance requirements in these sections as they imply there.
In addition to all previously detailed installation requirements, mobile home in-stallations
must meet the following requirements in accordance with the Manufactured Home and
Saftey Standard (HUD) CFR 3280, Part 24:
Permanently bolt your stove to the floor, (A), figure 25.
Electrically ground your stove or the pedestal to the steel frame of the home. Use a number 8 gauge
copper wire, (B), figure 25, or equivalent.
The stove must have a permanent outside air source with a ¼ inch screen over the inlet.
Figure 26, (B, C & D)
For transportation all chimney/vent above the mobile home must be removed.
Chimney/PL Vent must be 3” or 4” PL Vent and when extending through the roof, must extend a
minimum or 36” above the roofline of the mobile home and must be installed using a UL / ULC
listed ceiling fire stop (J), figure 26, and rain cap (L), figure 26.
REFER TO THE VENTING DIAGRAMS IN THIS MANUAL FOR FURTHER EXHUAST CONFIGURATIONS.
INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.
Figure 25 Figure 26
Note: When moving your mobile home, all exterior venting must be removed. Upon completion of relocation,
all venting must be reinstalled, gas tight, and securely fastened.
B
A
CD
EFG
H
J
K
L

FRAME
HEARTH PAD
FLOOR
BGROUND
WIRE
ABOLT(S)
PelPro Appliances www.pelprostoves.com 18
AFloor Pad
BCombustion Air Intake
CFresh Air Duct
DFresh Air Hood
EStove Exhaust
FPipe Adapter
GClean Out Tee
HTee Support Bracket
IPipe
JFirestop Spacer / Ceiling Sup-
port
KRoof Flashing / Storm Collar
LRain Cap

19
Walkout Basement or Main Floor
Basement or Main Floor
1Pipe Adapter
Clean Out Tee & Cap
Tee Support Bracket
Horizontal Rain Cap
2
3
4
5
6
7
8
90 Deg Elbow
36” Pipe Length
12” Pipe Length
12” Adjustable Pipe Length
Wall Thimble9
1 Pipe Adapter
Clean Out Tee & Cap
Tee Support Bracket
Horizontal Rain Cap
2
3
4
5
6
7
890 Deg Elbow
36” Pipe Length
12” Pipe Length
12” Adjustable Pipe Length
Wall Thimble
9
10 24” Pipe Length x 2
10
1
2
3
4
5
6
7
8
Ground Level
Floor / Ceiling
12”
12”
9
9
Tube of RTV Silicone
Roll of Foil Tape
3/8” Stainless Self-Tapping
Screws x 27
2” Wood Screws x 10 Options
Tube of RTV Silicone
Roll of Foil Tape
3/8” Stainless Self-Tapping
Screws x 21
2” Wood Screws x 10
1
23
4
5
6
78
9
These styles of installation are highly recommended, due to possible backpressure in the exhaust caused by
airflow around the outside of the structure, snow build-up, or power failure, etc.. These designs will improve
venting performance and provide natural draft to help evacuate smoke from the appliance in case of power
failure.
Follow the same basic steps in locating your appliance, attaching the exhaust system and outside air intake to
your stove as the previous examples.
1
2
34
5
6
78
Main Floor - Vertical
1 Pipe Adapter
Clean Out Tee & Cap
3 x 60” (15’) Pipe Length
Tee Support Bracket
Ceiling Support / Firestop Spacer
Roof Flashing
Storm Collar
Vertical Rain Cap
2
3
4
5
6
7
8
Tube of RTV Silicone
Roll of Foil Tape
3/8” Stainless Self-Tapping
Screws x 27
2” Wood Screws x 10
8”
16”
Optional
Metal Plate
1
2
3
4
5
6
7
8
9
24”
Hearth Stove - Existing Reline
1 Pipe Adapter
Single Wall Stainless Steel
Clean Out Tee & Cap
Storm Collar
Vertical Rain Cap
2
3
4
5
6
7
8
Hi Heat Insulation
“All Fuel” Stainless Steel
Flex Liner
Roof Flashing
Liner Support
Dripless Connection
9
Tube of RTV Silicone
Roll of Foil Tape
3/8” Stainless Self-Tapping
Screws x 27
6”
PL Vent Length10
10
Outside Air may be obtained from a suitable duct passing through the
ash clean-out opening.
Ensure the chimney top is properly sealed to prevent intrusion of
weatherand down drafts with suitable flashings, collars, and sealants.
F
FREESTANDING
REESTANDING
I INSTALLATION
NSTALLATION
...C
...CON
ON’
’T
T
PelPro Appliances www.pelprostoves.com 19

20
F
FREESTANDING
REESTANDING
I INSTALLATION
NSTALLATION
...C
...CON
ON’
’T
T
PelPro Appliances www.pelprostoves.com 20
F
FIREPLACE
IREPLACE
I INSERT
NSERT
I INSTALLATION
NSTALLATION
2
Main Floor - Tie-In Claytile Flue
1“PL” Pipe Adapter
Single Wall Stainless Steel
Clean Out Tee & Cap
Storm Collar
Vertical Rain Cap
2
3
4
5
6
7
8
Hi Heat Insulation
“All Fuel” Stainless Steel
Flex Liner or “PL” Venting
Roof Flashing
Liner Support
Dripless Connection
9
Tube of RTV Silicone
Roll of Foil Tape
3/8” Stainless Self-Tapping
Screws x 27
7
6
24”
8
“PL” Clean Out Tee & Cap
“PL” Length of Pipe
“PL” 90D Elbow
“PL” Wall Thimble
10
11
12
1
2
3
4
5
Cleanout
Door
9
10
11 Main Floor - Class ATie-In
1 Pipe Adapter
Clean Out Tee & Cap
3 x 60” (15’) Pipe Length
Tee Support Bracket
Ceiling Support / Firestop Spacer
Roof Flashing
Storm Collar
Vertical Rain Cap
2
3
4
5
6
7
8
Tube of RTV Silicone
Roll of Foil Tape
3/8” Stainless Self-Tapping
Screws x 27 Outside Air
Intake
“PL” Adjustable length
“PL” to Class AAdaptor
Class AFittings
Lengths of Pipe
9
10
11
1
3
4
5
6
7
8
910
11
Installing Pellet Inserts into Factory Built or Masonry Fireplaces:
The insert must be tested and meet the requirements of UL1482 (US) and or ULC8628 (CAN) when
Tested in a masonry fireplace built per ULC S628.
The factory-built fireplace must be listed per UL127 or ULC8610.
Clearances obtained from the masonry fireplace tests are also relevant for installation in factory-built
fireplaces.
Installation must include a full height listed chimney liner meeting type HT requirements (2100D F)
per UL1777 (US) or ULC 8635 (CAN). The stainless steel liner must be securely attached to the insert
flue collar and the chimney top.
Means must be provided to prevent room air passage to the chimney cavity of the fireplace. This may
be accomplished by sealing the damper area around the chimney liner.
The airflow within and around the fireplace shall not be altered by the installation of the insert (i.e. no
louvers or outlet ports are blocked), unless specifically tested as such for each factory-built fireplace
manufacturer and model line.
NOTE: using a louvered faceplate (surround) complies with this requirement.
Alteration of the fireplace in any manner is NOT permitted with the following EXCEPTIONS:
1. External trim pieces which do not affect the operation of the fireplace my be removed
Providing they can be stored on or within the fireplace for re-assembly, if the insert is
removed.
2. The chimney damper may be removed to install the chimney liner.
Circulating air chambers (i.e. in a steel fireplace liner or metal heat circulator) shall not be blocked.
The PelPro Series Multi-Fuel Inserts may be installed in either a masonry or factory built fireplace.