Pelpro PPC90 User manual

PelPro Cast Iron Pellet Stove
Please read this entire manual before installation and use of this pellet fuel-burning room heater, and save for future refer-
ence. Failure to follow these instructions could result in property damage, bodily injury or even death. Contact local building or
re ofcials about restrictions and installation inspection requirements in your area.
Note: To obtain a French translation of this manual, please contact your dealer or visit www.pelprostoves.com. Pour obtenir
une traduction francaise de ce manuel, s’il vous plait contracter votre revendeur ou visitez www.pelprostoves.com
WARNING!

PelPro Cast Pellet Stove • 7093-600 • 07/13/16 pelprostoves.com2
Get to Know Your PelPro®Stove
Vacuum SwitchDigital Control
Ambient Probe
Convection Blower
Outside Air
Connection
Optional External
Thermonstat Connection
Vacuum Switch
Exhaust Blower
Exhaust Probe
Exhaust
Connection
Snap Disc
Drop Tube
Firepot
Igniter
(Behind Firepot)
Baffles (3)
Safety First!
Safety Alert Key: It is important to pay attention to alerts you will see throughout this manual to ensure your safety.
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
•WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• Notice: Indicates practices which may cause damage to the appliance or to property.
• Pro Tip: Indicates additional information to help you better understand your stove and optimize its performance.
Notice: Fire Risk
Pelpro disclaims any responsibility, and the warranty and agency listing will be voided, by the below actions.
DO NOT:
• Install or operate damaged appliance
• Modify appliance
• Install other than as instructed by the manufacturer
• Operate the appliance without fully assembling all components
• Over re (burning at higher temperatures than recommended causing permanent damage to the stove)
• Install any component not approved by the manufacturer
• Install parts or components not listed or approved
• Disable safety switches
Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance
or additional information, consult a qualied installer, service agency or your dealer.
DANGER! HOT SURFACES!
Glass and other surfaces are hot during operation AND cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away; if you expect that children may come into contact with this appliance, we recommend a barrier
such as a decorative screen (see your retailer for suggestions)
• CAREFULLY SUPERVISE children in same room as stove
• Alert children and adults to hazards of high temperatures
High temperatures may ignite clothing or other ammable materials.
• Keep clothing, furniture, draperies and other ammable materials away

PelPro Cast Pellet Stove • 7093-600 • 07/13/16pelprostoves.com 3
Table of Contents
Getting Started........................................................4
• Pallet removal
• What’s included
• What you’ll need
Installing Your Stove...............................................6
• Getting ready
• Placing your stove
• Venting your stove
Using Your Stove..................................................13
• Starting your stove
• What to expect
• Comfort settings
• Turning your stove off
Maintaining Your Stove........................................18
• What you may need
• Where, when and how
Troubleshooting....................................................22
• Power related
• Blockage related
Support...................................................................27
• Contact information
• Ordering Parts
Listings and Certications...................................28
• Mobile home approval
• Glass specication
• Efciencies
• Stove dimensions
• Warranty

PelPro Cast Pellet Stove • 7093-600 • 07/13/16 pelprostoves.com4
Getting Started
WARNING!
Inspect appliance and components for damage.
Damaged parts may impair safe operation.
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to consumer care.
Getting Started
Pallet Removal
There are bolts holding your PelPro stove in place
on the pallet. To remove your stove from the pallet:
What’s Included
1 2
Using a 3/8” wrench,
remove each bolt by
reaching under your
stove. Tip your stove
to opposite side and
push bracket inward;
set stove down and
repeat on other side.
Using a 7/16” wrench,
remove all four bolts
attaching the shipping
bracket to pallet.
Owner’s
manual
Door handleCleaning tool Power cord
Pallet Removal
Visit pelprostoves.com
or scan this code.
Outside air kit
components:
2” Flex hose Termination Cap Hose clamp Screws (4)
CAUTION!
Risk of cuts, abrasions or ying debris. Wear
protective gloves & safety glasses during install.
Metal edges are sharp.
Online Installation &
Trouble Shooting Videos

PelPro Cast Pellet Stove • 7093-600 • 07/13/16pelprostoves.com 5
Getting Started
Getting Started
What You’ll Need
Tools & Supplies
• High temperature silicone
(500°F+)
• Level
• Phillips screwdriver
• Plumb line
• Tape measure
• Framing square
• Reciprocating saw
• Electric drill & bits
• Caulking gun
• Stud nder
• Utility knife
• Pliers
• Flashlight
• Hammer
Safety Equipment
Recommended for all installation and maintenance steps.
Pellet Vent Pipe
Must be an approved 3” or 4” diameter Type “L” or “PL” vent. Use 4” diameter vent if ue height
is over 15’ or if installation is over 3,000 ft. above sea level.
Floor Protection
Non-combustible material
(such as a hearth pad) is
required underneath your
stove.
Surge Protector
Protect the electrical
components of your stove
by using a surge protector.
Pellet Fuel
Use only wood pellets
in your stove. For best
performance, use
premium, low-ash pellets
(<1%) less than 1.5” in
length and avoid the dusty
bits and pieces of pellets
in the bottom of the bag.
WARNING!
Fire Risk. NO OTHER vent components may be used. Substitute or damaged vent components may
impair safe operation.
Gloves Safety Glasses Close-toed shoes

PelPro Cast Pellet Stove • 7093-600 • 07/13/16 pelprostoves.com6
Installing Your Stove
Installing Your Stove
Your Home Acts Like a Chimney
We recommend that you help your home by:
1. Using a minimum of 5 feet of vertical venting
2. Use the supplied outside air kit
3. Install your stove on a main oor location
This will:
• Help your stove breathe
• Minimize smoke leakage in the house
• Enhance performance
Clearance to Combustibles
The space between your stove and the items in
your home that could burn. Materials such as:
• Wood
• Sheet rock (drywall)
• Carpet
A
A
B
B
G
E
D
J
Pro Tip
We highly recommend your stove and pellet vent pipe be installed by a professional installer. Your
retailer can make recommendations for you.
Installation MUST comply with local, regional, state and national codes and regulations.
Consult insurance carrier, local building inspector, re ofcials or authorities having jurisdic-
tion over restrictions, installation inspection and permits.
1
23
WARNING!
Asphyxiation Risk.
DO NOT INSTALL IN A SLEEPING ROOM. Consumes oxygen in the room.
For Canada, the installation must conform to CAN/CSA-B365
Placement
Where you place your stove can signicantly affect its performance and safety.
Getting Ready

PelPro Cast Pellet Stove • 7093-600 • 07/13/16pelprostoves.com 7
Installing Your Stove
Installing Your Stove
REQUIRED:
Use only 3” or 4” type “L” or “PL” pellet pipe.
CAUTION
• Do not connect to any air distribution duct or system
• Do not install a ue damper in the exhaust venting system of this
stove
• Do not connect this stove to a chimney ue serving another
appliance
• The structural integrity of the manufactured home oor, wall and
ceiling/roof must be maintained
C
C
Installation Video
Visit pelprostoves.com or scan this code:
Pro Tip
This unit can be installed with a 3 to 6 inch (76-152mm) Top Vent Offset Adapter Kit. The 3
to 6 inch (76-152mm) Top Vent Offset Adapter are tested to use 24 gauge single wall ue
connector or Listed double wall ue connector to Class A Listed metal chimneys, or masonry
chimneys meeting International Conference of Building Ofcials (ICBO) standards for solid
fuel appliances.
Getting Ready (Continued)
Pellet Venting
Adding bends in the exhaust path restricts air ow,
reduces performance and provides a collection point
for ash deposits requiring more frequent cleaning.

PelPro Cast Pellet Stove • 7093-600 • 07/13/16 pelprostoves.com8
Installing Your Stove
Vent Termination Clearances
Installing Your Stove
A
D
B
L
C
K
J
B
I
H
G
F
Clearances
A 12” Clearance above grade, veranda porch, deck or balcony (Including vegetation and mulch)
B
12” with outside air kit
48” no outside air kit Clearance beside or below any windows or doors that open
12”* Clearance above any window or door that opens
C 18” Vertical clearance to ventilated soft located above the terminal within a horizontal distance of 2 feet from
the center line of the terminal
D 12” Clearance to an outside corner wall
F12” with outside air kit
48” no outside air kit
Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other
appliance
G 36” Clearance to a mechanical air supply inlet
H 84”** Clearance above a paved sidewalk or paved driveway located on public property
I 12”** Clearance under a veranda, porch, deck or balcony
J 12” Clearance above the roof
K 24” Clearance from an adjacent wall including neighboring buildings
L
36” within a height of 15
feet above the meter /
regulator assembly
Clearance to each side of center line extended above natural gas or propane meter / regulator assembly
or mechanical vent
Notice:
Do NOT terminate vent:
• In any location that will allow ue gases or soot from
entering or staining the building
• In any location which could create a nuisance or hazard
• In any enclosed or semi-enclosed area such as a
carport, garage, attic, crawl space, under a sun deck or
porch or narrow walkway
• Closely fenced area, or any location that can build up
a concentration of fumes such as a stairwell, covered
breezeway, etc.
Notice:
Do NOT terminate below an air inlet.
• It is recommended that at least 60” (1.52m) of vertical
pipe be installed when appliance is vented directly
through a wall—this will create a natural draft, which
will help prevent the possibility of smoke or odor
venting into the home during a power outage
• It will also keep exhaust from causing a nuisance
or hazard by exposing people or shrubs to high
temperatures
• The safest and preferred venting method is to extend
the vent vertically through the roof or above the roof
*Recommended to prevent condensation on windows and thermal breakage. **This is a recommended distance. For additional requirements check local codes.

PelPro Cast Pellet Stove • 7093-600 • 07/13/16pelprostoves.com 9
Installing Your Stove
Installing Your Stove
Conrm required clearances to combustibles:
Notice: Be careful to protect the bottom of the stove
and oor surfaces when moving the stove. Bottom
edges of stove are sharp and can scratch surfaces.
1
1
2
3
Vertical Installations (Interior Flue)
Straight back against wall Inches mm
D Back wall to pellet pipe 3 76
E Side wall to stove 13 330
USA Hearth Pad Requirements Inches mm
A Sides 2 51
B Back 2 51
C Front 6 152
Horizontal Installations
Straight back against wall Inches mm
G Back wall to stove 2 51
E Side wall to stove 13 330
H Clearance to top of stove 7 178
J Clearance to front of stove 48 1219
Corner Installation
Straight back against wall Inches mm
F Walls to stove 3 76
2
B*
A
C
A
Placing Your Stove
Stove must be installed on a non-combustible oor.
If needed, place oor protection (such as a hearth
pad) beneath the stove. Move stove from pallet onto
your non-combustible surface. Do not operate the
stove while it sits on the pallet.
Hearth pad minimum requirements:
Notice: Clearances may only be reduced by means
approved by the regulatory authority having jurisdiction.
Non-combustible oor protection extending beneath the ue pipe is required
with horizontal venting or under the top vent adapter with vertical installation.
*Non-combustible oor protection must extend 2 inches (51mm) beneath the
ue pipe when installed horizontal venting or under the top vent adapter with
vertical installation. CANADA REQUIRED, USA RECOMMENDED.
3
G
E
D
J
F
F
J
H
J
Canada Hearth Pad Requirements Inches mm
A Sides 8 203
B Back 2 51
C Front 6 152

PelPro Cast Pellet Stove • 7093-600 • 07/13/16 pelprostoves.com10
Installing Your Stove
Installing Your Stove
Pro Tips
• See venting manufacturer’s required clearances to combustibles
• For horizontal installations, the minimum clearance from exterior to termination cap is 6”—you
may want to increase to 18” clearance to minimize soot blow back on home exterior.
Install venting. (For additional installation options visit pelprostoves.com)
3
Install wall thimble (sold separately) per manufacturer requirements.
2
Vertical - Interior, Preferred Installation
6 in.
(152mm)
Min.
Clean-out T
Firestop
Flashing
Rain Cap
Non-combustible Hearth Pad
12 in. (305mm) Minimum
Ceiling Support
Follow pipe manufacturer
listed clearance
Exterior - Optional Installations
Non-combustible
Hearth Pad
Wall Thimble
Horizontal
Termination Cap
Termination
Cap
6 in. (152 mm)
Minimum
6 in.
(152 mm)
Minimum
Clean Out T
Wall Thimble
6 in.
(152 mm)
Minimum
Venting Your Stove
CAUTION!
Take appropriate precautions to locate utilities within the wall and avoid contact.
WARNING!
Do not terminate venting in any enclosed or semi-enclosed area
such as: a carport, garage, attic, crawl space, under a sun deck
or porch, narrow walkway or closely fenced area, or any location
that can build up a concentration of fumes such as a stairwell,
covered breezeway, etc.
CAUTION!
Ensure that your stove venting terminates above
your stove. The following may occur:
• Your stove appliance will not draft properly
• Smoke may seep in your house
• Excessive sooting
Install vent at clearances specied by the manufacturer
Use silicone to create an effective vapor barrier at the location where the chimney or
other component penetrates to the exterior of the structure.
4
NOTE: In Canada when using a factory-built chimney it must be safety listed, Type UL103 HT (2100
o
F) CLASS “A” or
conforming to CAN/ULC-S629M, STANDARD FOR 650oC FACTORY-BUILT CHIMNEYS.
Mark and cut wall for venting penetration on exterior wall (if needed).
1

PelPro Cast Pellet Stove • 7093-600 • 07/13/16pelprostoves.com 11
Installing Your Stove
• 45° elbow is equivalent to 1 foot of straight pipe
• 90° elbow is equivalent to 3 feet of straight pipe
Installing Your Stove
Notice:
These are guidelines for successful venting of
your pellet appliance. The more vertical rise
you can obtain in your system, the better it will
perform. Horizontal vent runs can accumulate
ash and will need to be cleaned more often.
Try to keep them as short as possible.
Venting Your Stove
The maximum horizontal venting allowed with no vertical
venting attached is 48 inches including one 90° elbow
or two 45° elbows. Addition of any horizontal venting
beyond 48 inches requires a minimum 60 inches of
additional vertical vent. Horizontal sections of vent pipe
should have a 1/4 inch rise per foot. We recommend
using the shortest venting and fewest elbows possible
when venting horizontal.
We recommend the use of 4 inch vent with any
installation requiring more than two 90° elbows, or more
than 15 feet of venting.
Minimum Vertical Vent for One Elbow
0
5
10
15
20
0 5 10 15 20
Horizontal Run, (ft)
Minimum Vertical Rise
(ft)
Horizontal Run (FT)
Minimum Vertical Vent for One Elbow
0
5
10
15
20
0 5 10 15
Minimum Vertical
Rise, (ft)
Minimum Vertical Vent for Two Elbows
Length of Horizontal Sections (FT)
0
5
10
15
20
25
0246 8 10 12
Minimum Vertical Rise
(ft)
Minimum Vertical Vent for Three Elbows
Length of Horizontal Sections (FT)
ONE 90° ELBOW
Total
Horizontal
Minimum
Vertical
Vent
Diameter
403
553
663
773
884
994
10 10 4
11 11 4
12 12 4
13 13 4
14 14 4
15 15 4
16 16 4
17 17 4
18 18 4
19 19 4
TWO 90° ELBOWS
Total
Horizontal
Minimum
Vertical
Vent
Diameter
253
363
473
583
693
7 10 4
8 11 4
9 12 4
10 13 4
11 14 4
12 15 4
13 16 4
14 17 4
15 18 4
THREE 90° ELBOWS
Total
Horizontal
Minimum
Vertical
Vent
Diameter
2 11 4
3 12 4
4 13 4
5 14 4
6 15 4
7 16 4
8 17 4
9 18 4
10 19 4
11 20 4
WARNING!
Fire Risk.
• Only LISTED venting
components may be
used
• NO OTHER vent components may be used.
Substitute or damaged vent components
may impair safe operation.

PelPro Cast Pellet Stove • 7093-600 • 07/13/16 pelprostoves.com12
Installing Your Stove
Installing Your Stove
Pro Tip
Installing a cleanout “T” (sold separately) to the rear
of your stove, when venting vertically can save time during cleaning.
Install outside air kit (included)
For optimal performance, PelPro recommends the
outside air kit for all installations. Outside air kit is
required for all mobile/manufactured home installations.
Install through wall B
• Maintain clearances from exhaust
• Remove knock out in the rear of stove
- Attach ex pipe to outside air connection
on stove
- Use hose clamp
- Route tube outside the structure
- Attach cap
- Secure to outside wall with appropriate fasteners
Take a Break
Inspect your work:
_____ Conrm clearances to combustibles are maintained
_____ Pipe joints are secure and properly sealed
_____ Outside air kit installed properly
_____ Conrm termination clearances
6B
CAUTION!
Never draw outside
combustion air from:
• Wall, oor or ceiling cavity
• Enclosed space such as an
attic, garage or crawl space.
• Install pellet venting through wall and connect vent/
pipe to stove A
• Some venting manufacturers offer pellet stove
adapters for their venting for easier installation
• Seal all pipe joints using high-temp silicone (500°+)
• Secure exhaust venting system to the appliance with
at least 3 screws or rivets per the pipe manufacturer’s
instructions. Also secure all connector pipe joints with
at least 3 screws through each joint.
• Install termination cap
• Conrm all required stove clearances to combustibles
A5

PelPro Cast Pellet Stove • 7093-600 • 07/13/16pelprostoves.com 13
Using Your Stove
Using Your Stove
Fuel Material and Fuel Storage
Pellet fuel quality can greatly uctuate. We recommend that you buy fuel in multi-ton lots
whenever possible. However, we do recommend trying various brands before purchasing
multi-ton lots to ensure your satisfaction. Store fuel in dry location not within clearances to
combustables of your stove.
Fuel Material
• Made from sawdust or wood by-products
• Depending on the source material it may have a high or low ash content.
Higher Ash Content Material
• Hardwoods with a high mineral content
• Fuel that contains bark
• Standard grade pellets or high ash pellets
Lower Ash Content Material
• Most softwoods
• Fuels with low mineral content
• Most premium grade pellets
Fuel Tips
Pro Tip
We recommend the use of Pellet Fuels Institute certied pellet fuel with this product.
Your stove has a manufacture-set minimum low burn rate that must not be altered. It is
against federal regulations to alter this setting or otherwise operate your stove in a manner
inconsistent with opertion instructions in this manual.

PelPro Cast Pellet Stove • 7093-600 • 07/13/16 pelprostoves.com14
Using Your Stove
WARNING!
HOT SURFACES! Glass and other surfaces are hot during operation AND cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as replace
• Alert children and adults to hazards of high temperatures
• High temperatures may ignite clothing or other ammable materials
• Keep clothing, furniture, draperies and other ammable materials away
1
2
4
3
What to Expect
1Combustion blower will turn on
2Igniter will turn on
3 Pellets will drop, smoke may occur in rebox but will
evacuate, and ame will appear in repot.
4Convection blower will automatically turn on after the
stove heats up. Convection blower will continue to
run even after your stove has been shut down.
Pro Tips
• Odors and vapors are released during initial startup after purchase; burning your stove on
HI for 30 minutes will allow the paint to cure. Open windows or doors for air circulation until
burn off is complete.
• During start up and normal operation your stove’s front door must be closed
• Priming is only required the rst time your stove is lit, or after a FUEL FEED ALARM.
Starting your stove the rst time
WARNING!
Fire Risk
Keep combustible materials, gasoline and other ammable vapors and liquids clear of appliance.
• Do NOT operate appliance with door open
• Do NOT operate appliance with repot oor open
• Do NOT store ammable materials in the appliance’s vicinity
• Do NOT use gasoline, lantern fuel, kerosene, charcoal lighter uid or similar liquids or gels to start or
“freshen up” a re in this heater
Keep all such liquids well away from the heater while it is in use as combustible materials may ignite.
Using Your Stove

PelPro Cast Pellet Stove • 7093-600 • 07/13/16pelprostoves.com 15
Using Your Stove
FRONT
Using Your Stove
Important:
Allow up to 20 minutes for
your stove to start.
1
Use and Care
Visit pelprostoves.com or scan this code:
1
Plug in your stove
WARNING! Shock hazard.
• Plug directly into properly grounded 3 prong receptacle
• Do NOT route cord under or in front of appliance
• Recommend the use of a surge protector
33
11
22
4
4
2
2
3
3
Conrm three bafes inside rebox are secure,
placing the side bafes before the center
Add some pellets to hopper and fully close lid
Conrm repot is properly positioned

PelPro Cast Pellet Stove • 7093-600 • 07/13/16 pelprostoves.com16
Using Your Stove
Using Your Stove
DOWN BUTTON
PRIME
55 Prime your stove:
1) From “OFF” press
2) Press and hold until display reads
“FEEDING.”
The feed motor will run about 2 minutes.
Comfort Settings
Control your comfort:
• POWER button - Used to turn your stove on, off and to reset.
• Adjust temperature – Set to your desired temperature level. Once the desired temperature
level is achieved the stove will automatically shut down. When the temperature in the room drops
below the desired temperature level, your stove will automatically restart.
• LO setting – Your stove will continue to run on low regardless of room temperature.
• HI setting - Your stove will continue to run on high regardless of room temperature.
Starting your stove from an empty hopper
ROOM:68 SET: 72
HEATING @%
Pro Tip
If your stove is turned to the off position and then back on, even if by mistake, your stove will
go through the shutdown process (approximately 15 minutes) and restart.
Thermostat
Your PelPro stove comes with a built-in thermostat system that provides easy temperature
adjustments. An external thermostat is available as an option (sold separately). To use an
external thermostat:
1Install according to the manufacture’s instructions and connect to the back of your stove.
2Set THERMOSTAT to EXTERNAL in settings menu on the digital display.
3Turn stove on and set desired power setting.
6Once feeding stops press power button.
ROOM:68 SET: HI
START UP 11:59
6
CAUTION:
During this process DO NOT:
• Try to restart, manually add pellets or use any type of accelerant
Pro Tip
For all menu items press after
making your selection to store
value.

PelPro Cast Pellet Stove • 7093-600 • 07/13/16pelprostoves.com 17
Using Your Stove
If your stove tries to start but fails on the initial burn, it will display MISSED IGNITION.
1. Turn your stove to off, remove and clean
the repot
2. Conrm repot is properly positioned
3. Ensure there are enough pellets in the hopper.
4. Prime your stove per previous instructions
PWR TO RESET
MISSED IGN
Using Your Stove
Trim Adjustment
Trim adjustment is located in the menu. This feature will
adjust the air/fuel ratio and below are examples of when to
use it:
WARNING!
This wood heater needs periodic inspecion and repair for proper operation. It is against federal regulations to
operate this wood heater in a manner inconsistent with operating instructions in this manual.
• If the re is too large, lazy or producing black soot, adjust trim down one level at a time and allow
15 minutes for stabilization before making another adjustment
• If your re is too small and sometimes goes out when there are pellets in the hopper, adjust
the trim up one level at a time and allow 15 minutes for stabilization before making another
adjustment.
Turning Your Stove Off
3
Auger stops feeding pellets. Blowers continue to run until
after the exhaust temperature
has cooled.
1
CAUTION!
Smoke Hazard
• Press power button on display to OFF,
let appliance completely cool and
exhaust blower must be off. Now you
can unplug appliance before servicing
• Smoke spillage into room can occur if
appliance is not cool before unplugging
Press and hold power button
for 3 seconds
2
-2
TRIM

PelPro Cast Pellet Stove • 7093-600 • 07/13/16 pelprostoves.com18
Maintaining Your Stove
Maintaining Your Stove
What You’ll Need
Metal container
with lid
Flue cleaning
brush
Ceramic glass cleaner &
non-abrasive cloth
Ash vacuumDropcloth
Gloves
Safety glassesCleaning tool
Cleaning & Maintenance
Important:
Regular cleaning helps to assure optimal performance of your stove. Please refer to page
29 to log your maintenance and cleaning.
Cleaning your stove
Visit pelprostoves.com or
scan this code:
Phillips head
screwdriver
Maintaing your stove
Visit pelprostoves.com or
scan this code:

PelPro Cast Pellet Stove • 7093-600 • 07/13/16pelprostoves.com 19
Maintaining Your Stove
Where, When and How
Maintaining Your Stove
Zone 1 - Firebox
Firepot
• Remove the repot
• Scrape clean and remove ashes
• Replace repot
Firebox
• Remove bafes and vacuum residual ash
• Remove ashes from rebox oor
Glass
• Apply ceramic glass cleaner
• Use non-abrasive cloth to remove residue
WARNING!
Disconnect stove from power supply before servicing
Disposal of Ashes
Ashes should be placed in a metal container with a tight tting lid. The closed container
of ashes should be placed on a non-combustible surface or on the ground, well away
from all combustible materials, pending nal disposal. If the ashes are to be disposed
of by burial in soil or otherwise locally dispersed, they should be retained in the closed
container until all embers have been thoroughly cooled.
WEEKLY AS NEEDED OR
Door Inspection
• The gasketing between the glass and rebox
should be inspected periodically to make sure
there is a good seal.
1
Zone
1
Zone
2
Zone
2
Zone 3
Zone
3
Zone
WARNING!
If using a vacuum to clean stove, be sure embers are thoroughly cooled to prevent a re in the
vacuum.

PelPro Cast Pellet Stove • 7093-600 • 07/13/16 pelprostoves.com20
Maintaining Your Stove
Zone 2 - Stove Body
Convection Blower
• Remove right side panel to access and
remove convection blower
• Vacuum any debris from the fan blades and
blower housing
Hopper
• Empty hopper of any pellets
• Vacuum any remaining pellets/debris from the
hopper
MONTHLY AS NEEDED OR
WARNING!
Glass is 5mm thick high temperature heat resistant ceramic glass.
• DO NOT REPLACE with any other material
• Alternate material may shatter and cause injury
CAUTION!
Handle glass assembly with care and refer to maintenance instructions. When cleaning glass:
• Avoid striking, scratching or slamming glass.
• Do NOT clean glass when hot
• Do NOT use abrasive cleaners
• Do NOT operate with glass cracked, broken or scratched
Maintaining Your Stove
Pro Tip
The type of fuel you are burning will dictate how often you have to clean your repot.
If the fuel you are burning has a high dirt or ash content, it may be necessary to clean the
repot more than once a day.
Poor quality fuel will cause clinkers to form in the repot. Clinkers are formed when dirt, ash
or a non-burnable substance is heated to 2000 deg. F (1093 deg. C) and becomes glass-
like.
Always burn dry fuel. Burning fuel with high moisture content take heat from the fuel and
tends to cool the appliance, robbing heat from your home.
Damp pellet fuel can clog the feed system.
1
Zone
1
Zone
2
Zone
2
Zone 3
Zone
3
Zone