Penguin Edge PCIE-8130 User manual

1 Box contents
Make sure you receive all items of your shipment:
• One PCIE-8130 card
• One printed copy of Quick Start Guide (this document)
• One printed copy of Safety Notes Summary
When installing or servicing the system or accessories,
strictly observe the safety precautions in the Safety Notes
Summary. Ignoring these instructions can void the system
warranty and cause personal injury or property damage.
2 ESD
Electrostatic discharge and incorrect installation or
removal of the card can damage circuit or shorten its life.
Use a properly grounded ESD wrist strap or work in an
ESD-safe environment.
Connect to the ESD connector at the front or the rear of
the system.
3 Site preparation
Note: Consult the installation manual provided by your server
vendor for instruction on how to install the card in a specific server.
1. Make sure that all environmental and power requirements
defined in the PCIE-8130 Installation and Use manual are
met.
2. The PCIE-8130 card requires a PCIe x4 connector size. It can
also be installed in a x8 or x16 slot.
3. The PCIE-8130 can be installed in a system board PCIe slot or
on a PCIe riser card.
4. Make sure the server can accommodate the full-height, half-
length PCIE-8130 card and that it provides snap-in fixation or
screw holes.
5. Verify that the I/O slot can supply power via the 12V supply rail in
accordance with the PCI Express Card Electromechanical
Specification definition for a 75W slot.
4 Install PCIe cards
Note: Consult the installation manual provided by your server
vendor for instructions on how to power down and remove the
housing cover from the system.
1. Shut down and disconnect the system from AC power.
2. Remove the housing cover from the server.
3. Remove the filler cards or filler panels in the PCIe slots, if any.
4. Install the PCIE-8130 card(s) in the respective slot(s) by gently
pushing the card along the guide rails till the card is fully
engaged with the connector. Avoid excessive force during this
operation.
Note: If a retainer clip is used in the target server to secure the
card, the clip must be applied for proper operation of the card.
5. Fill any empty PCIe slots with filler cards or filler panels. A slot
adjacent to the component side (primary side) of a high power
card should always contain a filler card for better cooling.
For more information about PCIE-8130 card installation, refer to the
PCIE-8130 Installation and Use manual.
5 Power connector info
Power for the PCIE-8130 card is supplied via the PCIe card edge
connector. No additional power (via ATX connectors) is used.
For more information about connecting cables and power cords,
refer to the PCIE-8130 Installation and Use manual.
Penguin Edge™
PCIE-8130
Quick Start Guide
P/N: 6806877A03C September 2022

Penguin Edge™ PCIE-8130 Quick Start Guide
Penguin Solutions™, 2900 S. Diablo Way, Suite 190, Tempe, Arizona 85282
For technical assistance or to report product damage or shortages,
contact your local Penguin Solutions sales representative or visit
https://www.penguinsolutions.com/edge/support/.
Technical Assistance
For more information on this product, see the PCIE-
8130 Installation and Use manual and other related
technical documentation, which can be found by
using the Documentation Search at
https://www.penguinsolutions.com/edge/support/.
Get More Information
Penguin Solutions is a trade name used by SMART Embedded Computing, Inc., a
wholly owned subsidiary of SMART Global Holdings, Inc. Penguin Edge is a
trademark owned by Penguin Computing, Inc., a wholly owned subsidiary of
SMART Global Holdings, Inc. All other logos, trade names, and trademarks are
the property of their respective owners. These materials are provided as a service
to our customers and may be used for informational purposes only. For full legal
terms and conditions, please visit www.penguinsolutions.com/edge/legal/.