Pentagram O'Pen Wide P 2004 User manual

INDEX
INTRODUCTION .....................................................................EN - 3
BOX CONTENTS................................................................EN - 3
MINIMUM SYSTEM REQUIREMENTS ..............................EN - 3
TABLET ELEMENTS ..........................................................EN - 3
BATTERY REPLACEMENT................................................EN - 4
TIP REPLACEMENT...........................................................EN - 4
LEDS AND BUTTONS ........................................................EN - 5
TABLET INSTALLATION.........................................................EN - 6
USING THE TABLET...............................................................EN - 7
TABLET CONFIGURATION ....................................................EN - 8
WINDOWS 2000/XP ...........................................................EN - 8
WINDOWS VISTA.............................................................EN - 10
MACRO KEY MANAGER APPLICATION.........................EN - 10
EINLEITUNG ...........................................................................DE - 3
INHALT DER VERPACKUNG.............................................DE - 3
MINDESTSYSTEMVORAUSSETZUNGEN ........................DE - 3
TABLETTFUNKTIONEN .....................................................DE - 3
BATTERIEWECHSEL.........................................................DE - 4
WECHSELN DER SPITZE..................................................DE - 5
LEUCHTDIODEN UND TASTEN........................................DE - 5
INSTALLATION DES TABLETTS............................................DE - 6
UMGANG MIT DEM TABLETT................................................DE - 7
KONFIGURATION DES TABLETTS .......................................DE - 8
WINDOWS 2000/XP ...........................................................DE - 8
WINDOWS VISTA.............................................................DE - 10
MACRO KEY MANAGER .................................................DE - 10
WPROWADZENIE................................................................... PL - 3
ZAWARTOŚĆ PUDEŁKA ................................................... PL - 3
MINIMALNE WYMAGANIA SYSTEMOWE......................... PL - 3
ELEMENTY TABLETU........................................................ PL - 3
WYMIANA BATERII............................................................ PL - 4
WYMIANA RYSIKA............................................................. PL - 5
DIODY I PRZYCISKI........................................................... PL - 5
INSTALACJA TABLETU.......................................................... PL - 6
KORZYSTANIE Z TABLETU ................................................... PL - 7
KONFIGURACJA TABLETU.................................................... PL - 8
WINDOWS 2000/XP ........................................................... PL - 8
WINDOWS VISTA............................................................. PL - 10
APLIKACJA MACRO KEY MANAGER ............................. PL - 10

NOTE! Any information and technical data are subject to change without
prior notification and/or indication in this manual.
Copyright 

 2007 PENTAGRAM
All rights reserved; copying and reproduction is strictly forbidden.
ACHTUNG! Alle Informationen und technische Angaben können sich
ändern, ohne dass es zuvor bekannt gegeben und/oder in dieser Anleitung
vermerkt wird.
Copyright 

 2007 PENTAGRAM
Alle Rechte vorbehalten, Vervielfältigung und Kopieren verboten.
UWAGA! Wszystkie informacje i dane techniczne mogąulec zmianie bez
wcześniejszego powiadomienia i/lub zaznaczenia tego w niniejszej
instrukcji.
Copyright


 2007 PENTAGRAM
Wszelkie prawa zastrzeŜone, powielanie i kopiowanie zabronione.

Installation and User’s manual
PENTAGRAM O’Pen Wide
(P 2004)
The latest versions of manuals, drivers and software are available on
www.pentagram.pl

O’Pen Wide (P 2004)
EN - 2

O’Pen Wide (P 2004)
EN - 3
Introduction
Thank you for purchasing Pentagram O’Pen Wide tablet, a graphical device for your computer.
Using O’Pen Wide tablet, you may do much more than previously using a mouse. The tablet
has been designed as a tool for graphics professionals and CAD/CAM applications. However,
thanks to reasonable price and plenty of functions, Pentagram tablets ale also appropriate for
home use.
NOTE! Make sure the tablet is far from a CRT (cathode ray tube) monitor and other sources of
strong electromagnetic field as they may interfere with the tablet operation.
Box contents
1. PENTAGRAM O’Pen Wide tablet
2. Pen
3. Pen holder
4. Spare pen tips (2 pieces)
5. Pen AAA battery
6. Tweezers for removing the pen tip
7. CDs with drivers and software
8. Quick installation manual
Minimum system requirements
• PC – Windows 2000 / XP / Vista operating system
• Mac – MacOS X 10.2.8 or newer
• Free USB port
Tablet elements
Knob Knob
LEDs and buttons
Function
fields
Working
area

O’Pen Wide (P 2004)
EN - 4
Battery replacement
1. Hold the pen as shown in the photo
2. Pull firmly the back pen part to separate it from the rest of the pen case
3. Open the battery compartment as shown in the picture
4. Remove the old battery and insert the new one, observing polarity
5. Assemble the pen
Tip replacement
After the pen has been used for a long time, the pen tip will shorten as a result of friction
against the tablet surface. A blunt tip does not pass the pressure force properly and should be
+
–

O’Pen Wide (P 2004)
EN - 5
replaced. The tablet comes with two spare tips and tweezers facilitating the tip replacement.
Follow the steps below to replace the tip:
1. Grab the tip with the supplied tweezers and pull it out gently from the pen case.
2. Insert a new tip instead of the old one.
3. Press the tip in carefully, holding the pen in vertical position.
LEDs and buttons
Power LED – blinks after connecting the tablet to the computer, lights when tracing the pen.
The LEDs above the buttons indicate knobs operating mode and work area dimensions. The
buttons and knobs operation requires installing the supplied drivers. Both tablet knobs work in
the same way. The center knob part serves as a button, and its function depends on the knob
operation mode (Scroll, Zoom, VOL). Knob functions may be different from the described
ones, depending on the application used.
Scroll – In this mode, the tablet knobs are used for scrolling the window contents vertically
and horizontally. The knob button changes the scrolling direction (vertical/horizontal).
Zoom – In this mode, the tablet knobs are used for changing the zoom factor. Pressing and
holding the knob button in this mode works as the “Hand” tool.
VOL – In this mode, the tablet knobs are used for adjustment of the sound card general
volume. The knob button turns the sound on and off (Mute).
Wide – Sets the tablet working area to 30.48 cm x 18.41 cm (the working area width is limited
by the function keys) and is designed for work with a wide-screen display.
4:3 – Sets the tablet working area to 24.13 cm x 18.41 cm (the working area width is limited by
vertical grooves visible under the tablet surface) and is designed for work with a standard
display.

O’Pen Wide (P 2004)
EN - 6
Tablet installation
Follow the steps below to install the tablet properly. The tablet drivers are designed for
Windows 2000/XP and Vista systems.
1. Insert the supplied CD with drivers into the CD-ROM drive in the computer.
2. If the installer does not launch automatically, click the Start > Run menu, enter X:\setup
(where X is the CD-ROM drive letter) and press Enter.
3. In the installer window, click the Macro Key Manager, to start the drivers and Macro Key
Manager application installer.
4. Follow the instructions displayed on the screen to install the drivers and the Macro Key
Manager application.
5. When the installation finishes, a prompt will display, asking the user to restart the
computer. Close all open applications and click the OK button.
6. After the computer has restarted, connect the tablet USB cable to a free computer USB
port and wait for the system to install the tablet.
7. Check whether all tablet functions work properly. A pen movement over the tablet surface
should cause the cursor movement on the screen.

O’Pen Wide (P 2004)
EN - 7
Using the tablet
Work with the tablet is very intuitive and comfortable, but the user needs to get used to it.
The key to the success in working with the tablet is holding the pen more vertically than when
using a ball point pen, and also tracking the cursor movement on the screen rather than
looking at the pen.
After the pen is put close enough to the tablet surface, it makes the tablet trace the pen
movement, and the cursor moves accordingly. Touching the tablet surface with the pen is
equivalent to a click with the left mouse button. The default functions of the pen side buttons
depend on the operating system:
• Windows 2000/XP – The right mouse button is replaced with the lower side button of the
pen. To perform a double click (double clicking with the left mouse button), either tap the
pen against the tablet surface twice in one place very quickly (trying not to displace the
pen), or press the upper side button of the pen. The pen side buttons’ functions may be
changed in the tablet driver.
• Windows Vista – The right mouse button is replaced with the upper side button of the
pen. You can also hold the pen touched in one place of the tablet surface and wait for the
visual effect. To perform a double click (double clicking with the left mouse button), tap
the pen against the tablet surface twice in one place very quickly (trying not to displace
the pen).
To save battery, the pen automatically switches into sleep mode when it is not used for
several minutes. If you do not use the pen for a longer time, put it in the supplied holder or lay
flat in a place where neither the tip nor the side buttons can be pressed. To wake the pen up
from the sleep mode, tap its tip against the tablet surface.

O’Pen Wide (P 2004)
EN - 8
Tablet configuration
Windows 2000/XP
You may access the tablet driver configuration by clicking the Tablet icon in the system
control panel or by choosing the option Pen Pad... in the context menu of the Macro Key
Manager application icon.
About tab
In this tab you can see the most important information concerning the tablet.
Unit – select if the tablet dimensions are to be displayed in inches (inch) or centimeters (cm)
Tracking Mode – select the tracking mode of the pen movements by the tablet:
• Pen (Absolute) – the tablet active area corresponds to the screen area.
• Mouse (Relative) – the tablet pen is treated as the mouse.
Below there is more information about the tablet: Tablet Model, Tablet Length, Tablet
Width, Driver Version and Firmware Version.

O’Pen Wide (P 2004)
EN - 9
Buttons tab
On this tab you may assign functions to the pen buttons, as well as adjust the pressure force
and height at which the tablet starts tracing the pen.
Side Button 2 – assigning a function to the upper side button of the pen.
Side Button 1 – assigning a function to the lower side button of the pen.
Default – restoring the default settings.
Pen Offset Value – to use the default tablet values, tick the Auto Setting field. To adjust the
height, untick the Auto Setting field, click the Adjust button and follow the instructions on the
screen.
Click Pressure – setting the pressure sensitivity.
Test – After clicking this button, a window will open, in which you may test the new pen
sensitivity settings.
To clear the work area, press the lower side button of the pen.
To close the test window, press the upper side button of the pen.

O’Pen Wide (P 2004)
EN - 10
Windows Vista
Tablet support is included in Windows Vista. Basic pen options (turning the pen buttons on
and off, configuration of their parameters) may be configured in the Pen and input devices
applet, which is visible in the classic layout of the system control panel.
Macro Key Manager application
This application enables the configuration of function fields and assigning functions to them
depending on the active application. By default, some keys are configured for Windows 2000,
XP and Vista systems, as well as for Photoimpact XL SE and Photoshop elements 4.0
programs.
Application context menu
Clicking the Macro Key Manager application icon in the system tray (next to the clock) with the
right mouse button causes the context menu to appear. Its items are described below:
About... – Opens the window with information about the software
version, driver version and firmware version.
Show – Displays the main application window. Double-clicking on the
application icon has the same effect.
Disable / Enable – Turns off/on the function fields.
Setting – Opens the window with the application settings.
Pen Pad... – Opens the driver configuration window.
Help – Displays the application help file.
Settings window
MakroKey Response time – When the pen touches a function field, this is the time after
which the function assigned to the field is performed. The value – when choosing 0, it is
enough to tap a function field with the pen to perform its function.
Pointing Sound – You may select whether tapping the tablet surface with the pen is to be
signaled with a sound (ON) or not (OFF).

O’Pen Wide (P 2004)
EN - 11
Main application window
Applications list – Choose from the list the application, for which you want to configure the
function fields.
New – Add a new application to the list.
Delete – Delete the selected application from the applications list (applications configured by
default cannot be removed).
Function fields list – Choose a field, the settings of which you want to change (fields
configured by default cannot be modified). To choose a function field for modification, you can
also click the button symbolizing its field in the preview.
Setting – Tick this field to turn on the selected function field.
Hint – Enter in the field the contents of the balloon, which will display on the monitor when the
pen is above the selected function field.
Linking – Enter the path to the file, which will be launched after pressing the selected function
field. To browse folders in order to find the file, press the ... button.
Confirm – Press this button to save the settings of the selected function field.
Enable this manager – Tick this field to turn on the function fields. Untick to turn them off.
OK – Close the main window with a prompt that current configuration has not been saved.
Cancel – Close the main window skipping the unsaved configuration changes.
Applications
list
Fields
list

O’Pen Wide (P 2004)
EN - 12
Adding a new application to the list
1. Click the New button in the main application window.
2. In the New window, in the File Name field enter the application name which will be
displayed on the applications list, and then in the Open(*.exe) field enter the executable
file name or click the ... button to display the list of applications installed in the system.
3. After clicking the ... button, the window Installed Software will display. It contains the list
of applications installed in the system. Highlight the application you want to add to the list
and click the OK button to select the application and close the window. Click the Cancel
button to close the window without choosing an application.
4. After selecting the displayed application name and the executable file, click OK to add
the application to the list and close the window, or Cancel, to close the window without
adding an application.

Installations- und Bedienungsanleitung
PENTAGRAM O’Pen Wide
(P 2004)
Die neueste Fassung der Anleitung, Treiber und Software sind auf der Seite
www.pentagram.pl erhältlich.

O’Pen Wide (P 2004)
DE - 2

O’Pen Wide (P 2004)
DE - 3
Einleitung
Wir bedanken uns für den Einkauf des Grafiktabletts PENTAGRAM O’Pen Wide, eines
grafischen Eingabegerätes für Ihren Computer. Nun können Sie mit dem Tablett O’Pen Wide
viel mehr als bisher mit einer Maus leisten. Das Grafiktablett wurde als ein Werkzeug für
Graphiker für CAD/CAM-Anwendungen entwickelt, jedoch sind die Tabletts von Pentagram
dank erschwinglichem Preis und breiten Anwendungsmöglichkeiten ideal auch für
Haushaltsanwendungen geeignet.
ACHTUNG! Stellen Sie sicher, dass Ihr Tablett vom CRT-Monitor (Bildröhrenmonitor) und
anderen Quellen starken elektromagnetischen Feldes entfernt eingesetzt wird, sonst können
sie den Betrieb des Tabletts beeinträchtigen.
Inhalt der Verpackung
1. Grafiktablett PENTAGRAM O’Pen Wide
2. Stift
3. Stifthalter
4. Ersatzspitzen für den Stift – 2 St.
5. AAA-Batterie für den Stift
6. Pinzette zum Herausziehen der Stiftspitze
7. CDs mit Treiber und Software
8. Kurzanleitung zur Installation
Mindestsystemvoraussetzungen
• PC mit Windows 2000 / XP / Vista
• Mac mit MacOS X 10.2.8 oder höher
• unbelegter USB-Port
Tablettfunktionen
Drehknopf Drehknopf
Leuchtdioden und Tasten
Funktionsfelder
Arbeitsfläche

O’Pen Wide (P 2004)
DE - 4
Batteriewechsel
1. Stift wie abgebildet halten.
2. Am hinteren Teil des Stiftes stark ziehen, um den Teil vom Ganzen zu trennen.
3. Batteriefach wie abgebildet öffnen.
4. Die leere Batterie herausnehmen und an ihre Stelle eine neue einlegen, dabei Polung
beachten.
5. Stift zusammenbauen.
+
–

O’Pen Wide (P 2004)
DE - 5
Wechseln der Spitze
Nach längerem Stifteinsatz verkürzt sich die Spitze infolge der Reibung an der
Tablettoberfläche. Eine abgestumpfte Stiftspitze kann den Anpressdruck nicht genau
wiedergeben, deswegen soll sie ersetzt werden. Dem Tablett liegen zwei zusätzliche Spitzen
sowie eine Pinzette zum leichten Wechsel der Spitze bei. Führen Sie nachfolgende Schritte
durch, um die Spitze zu wechseln:
1. Mit der beiliegenden Pinzette an der Spitze fassen und sorgfältig aus dem Stift
herausziehen.
2. Eine neue Spitze an die Stelle der abgenutzten einsetzen.
3. Die neue Spitze senkrecht stehend andrücken.
Leuchtdioden und Tasten
Stromdiode – blinkt nach dem Anschluss des Tabletts an den Computer; sie leuchtet
kontinuierlich, wenn Bewegungen des Stiftes verfolgt werden.
Die Leuchtdioden zeigen den Betriebsmodus der Drehknöpfe sowie Abmessungen der
Arbeitsfläche an. Tasten und Drehknöpfe erfordern zu ihrem Betrieb, dass die mitgelieferten
Treiber installiert sind. Beide Drehknöpfe des Tabletts arbeiten auf die gleiche Weise. Der
mittlere Teil eines Drehknopfes dient als eine Taste, deren Funktion vom Betriebsmodus der
Drehknöpfe (Scroll, Zoom, VOL) abhängt. Die Funktion der Drehknöpfe kann von der
beschriebenen abweichen, je nach Anwendung, mit der sie zum Einsatz kommen.
Scroll – In diesem Modus dienen die Drehknöpfe zum vertikalen und horizontalen
Verschieben des Fensterinhalts. Die Taste am Drehknopf dient zum Umkehren der
Scrollrichtung (vertikal/horizontal).
Zoom – In diesem Modus dienen die Drehknöpfe zum Ändern des Vergrößerungsfaktors. Das
Drücken und Gedrückthalten der Drehknopftaste wirkt wie das Werkzeug „Hand“.
VOL – In diesem Modus dienen die Drehknöpfe zum Einstellen der allgemeinen Lautstärke
der Soundkarte. Die Taste auf dem Drehknopf dient zum Ein-/Ausschalten der Stummfunktion
(Mute).
Wide – Die Arbeitsfläche des Tabletts wird als 30,48 cm x 18,41 cm festgelegt (die Breite der
Arbeitsfläche wird durch Funktionstasten eingeschränkt), sie ist zum Einsatz mit
Breitbildschirm-Monitoren bestimmt.
4:3 – Die Arbeitsfläche des Tabletts wird als 24,13 cm x 18,41 cm festgelegt (die Breite der
Arbeitsfläche wird durch sichtbare vertikale Schnitte unter der Tablettoberfläche
eingeschränkt), sie ist zum Einsatz mit einem üblichen Monitor bestimmt.

O’Pen Wide (P 2004)
DE - 6
Installation des Tabletts
Um das Grafiktablett korrekt zu installieren, führen Sie folgende Schritte aus: Treiber des
Tabletts sind für Windows 2000/XP und Vista bestimmt.
1. Legen sie die mitgelieferte Treiber-CD in das CD-Laufwerk in Ihrem Computer ein.
2. Startet der Installationsassistent nicht automatisch, wählen Sie Start > Ausführen,
geben Sie X:\setup ein (X steht für den Buchstaben des CD-Laufwerks) und drücken Sie
die Eingabetaste.
3. Im Fenster des Installationsassistenten klicken Sie auf Macro Key Manager, um die
Installationssoftware für Treiber und Anwendungen Macro Key Manager zu starten.
4. Den eingeblendeten Anweisungen folgen, um Treiber und die Anwendung Macro Key
Manager zu installieren.
5. Nachdem die Installation fertiggestellt ist, erscheint das Fenster mit einer Anweisung, das
System erneut zu starten; daraufhin alle Anwendungen schließen und auf die
Schaltfläche OK klicken.
6. Wenn der Computer erneut hochgefahren ist, das USB Kabel des Tabletts an einen
unbelegten USB Port am Computer anschließen und abwarten, bis das System das
Tablett installiert hat.
7. Überprüfen Sie, ob alle Funktionen des Tabletts aktiv sind. Die Bewegungen des Stiftes
über die Tablettoberfläche sollten Bewegungen des Cursors am Bildschirm auslösen.