Pentair Pool Products Kreepy Krauly User manual

2
Congratulations on purchasing the best pool-cleaning system in the world! Your new Kreepy Krauly will
provide you with years of carefree pool enjoyment, as it efficiently vacuums your pool for you. Before
long, you’ll wonder how you ever got along without Kreepy Krauly.
First, however, you’ll have to install Kreepy Krauly and perhaps make some minor adjustments. This
manual provides step-by-step instructions needed to install and adjust Kreepy Krauly.
Contents
Please record the serial number of your Kreepy Krauly in the space below. This way, if you
need to refer to the serial number in the future (e.g. if you call the Customer Helpline), it will be
readily available. The diagram on page 3 shows where Kreepy Krauly’s serial number is located.
Kreepy Krauly Serial Number ________________________________
Activate Kreepy Krauly’s Warranty
You will also need to record this serial number on Kreepy Krauly’s warranty registration card.
Complete and return the card to activate Kreepy Krauly’s warranty. The registration card is self-
addressed and postage-paid for your convenience.
Toll-free Customer Helpline
If you have questions about your Kreepy Krauly, check the instructions in this manual. If you still
have a question, call our Customer Helpline at 1-800-443-5711. Please have your Kreepy Krauly serial
number ready when you call.
Warranty Note
Cleaners purchased in the United States of America from entities outside the United States do not
qualify for any United States programs including warranty, trade-in, or rebate programs.
Welcome
Important Warning and Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
I. Pool Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
II. Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
III. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
IV. Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
V. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
61................................seirosseccAdnaeso.H,straPyluarKypeerK.IV
VII. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
VIII. Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

IMPORTANT WARNING AND SAFETY INSTRUCTIONS
Important Notice:
Attention Installer: This guide contains important information about the installation, operation and safe use of
this product. This information should be given to the owner and/or operator of this equipment after installation of the
pool cleaner.
Attention User: This manual contains important information that will help you in operating and maintaining this
pool cleaner. Please retain it for future reference. Consult Pentair Water Pool and Spa (“Pentair”) with any questions
regarding this equipment.
WARNING — Before installing this product, read and follow all warning notices and instructions which are
included. Failure to follow safety warnings and instructions can result in severe injury, death, or property damage. Call
[phone] for additional free copies of these instructions.
Consumer Information and Safety
The Kreepy Krauly® pool cleaners are designed and manufactured to provide many years of safe and reliable service
when installed, operated and maintained according to the information in this manual. Throughout the manual, safety
warningsandcautionsareidentifiedbythe“ “symbol.Besuretoreadandcomplywithallofthewarningsandcautions.
WARNING — Hazardous suction. Do not play with cleaner or hose or apply to body. Can trap and tear hair
or body parts. Hose can trip or entangle swimmers which could result in drowning.
WARNING — Suction entrapment, injury, and drowning hazard. If your pool has a dedicated suction port
(“vac port”) for vacuuming or for an automatic pool cleaner, it must be covered when not in
use. A spring loaded safety cover (a “vac port fitting”) is included with your cleaner. Install it on
the suction port to prevent entrapment and injury. If the cover provided does not fit, purchase one
that does from your local pool store and install it instead. The cover should conform to IAPMO
SPS4-99A.
WARNING — Stop pump before attempting to clean unit. Do not allow swimmers in pool while pool cleaner
is operating.
WARNING — To reduce the risk of injury, do not let children use or play with pool cleaner.
WARNING — Do not allow swimmers in the pool while pool cleaner is operating. Hose can trip or entangle
swimmers which could result in drowning.
CAUTION — Moving parts may injure hands or fingers. Stop pump before attempting to clean out pool
cleaner head.
3

GENERAL INSTALLATION INFORMATION
Pre-installation check list
Before installing your cleaner, review and understand all warnings and safety information in this guide. Failure to
follow these instructions or improper installation of the cleaner can result in damage to the pool finish or the vinyl
liner, Pentair Water Pool and Spa, Inc. disclaims any liability for repairs or replacement to any of these structures
or components of the customer’s pool.
Before installing the cleaner in a vinyl liner pool:
Check liner closely for signs of deterioration or damage from age, chemicals, pool wall damage, etc. If any
damage is found, have a qualified pool professional make all the necessary repairs. Also, if there are stones,
roots, etc., under the liner, remove them before installing the cleaner.
Before installing the cleaner in a gunite pool or a pool that is partially or completely tiled:
Repair loose tiles and tighten any loose light rings.
Before installing the cleaner, clean your filter system:
Make sure you have cleaned the filter, including backwashing, rinsing, and emptying all baskets. A clean
system is necessary for proper cleaner operation and coverage.
Before installing the cleaner, fill the hose with water:
Always make sure the cleaner head is submerged and the hose is full of water before connecting the hose to
the filtration system (whether through a skimmer or dedicated wall fitting). Air in the system can damage the
pump through dry running and overheating.
Before installing the cleaner, understand cleaner coverage:
The cleaner is designed to rid your pool of debris in approximately 4-6 hours. Less time could be needed,
depending on the pool size. The cleaner was not designed to automatically clean steps or swimouts or to
work under a solar cover. It was also not designed to do initial cleanup for a new pool or when opening your
pool for the season.
AFTER installing the cleaner, make sure the cleaner is operating correctly :
The cleaner may need some minor adjustments to make sure it is operating properly so there is no damage
to the pool finish. Certain vinyl liner patterns are particularly susceptible to surface wear, pattern removal, ink
rubbing off of, or serious scratches to the pattern caused by objects coming into contact with the vinyl surface,
including automatic pool cleaners. Pentair Water Pool and Spa, Inc. is not responsible for any pattern removal,
abrasions or markings on vinyl liners.
4

Disclaimer of Liability
About Your Pool and Kreepy Krauly
There are a multitude of factors that contribute to the life of your pool. TheKreepy Krauly automatic pool cleaner is a very passive
product that will have no impact on pool life.
Pleasebeawarethatovertime,deterioration,discolorationandbrittlenessofanypoolfinishcanbecausedseparatelyby,orincombination
with, age, an imbalance in pool water chemistry, improper installation and other factors.An automatic pool cleaner, such as
Kreepy
Krauly will not remove or cause wear on “good” pool plaster. In fact, the opposite is true–pool plaster will eventually cause wear on
thecleaner.
The same situation holds true for vinyl-lined in-ground swimming pools, because vinyl liners are also affected by the environment and
factorssuchas pool waterchemistry, sunlightandthepool’ssurroundings.Therefore over time,vinyl canbecome brittle andweak.In
addition,vinyl-linedpoolsareaffectedbytheworkmanship,compositionandinstallationofthelinerandtheworkmanshipandqualityof
construction of the supporting walls and pool base. These are all factors which can contributeto liner failure. The existenceof any of
thesetype of conditionsin your poolis notcaused by theuse or operationof KreepyKrauly . The manufacturerdisclaims any liability
for repairs or replacement to any of these structures or components of the customer’s pool.
The pool owner must assume all responsibility for the condition and maintenance of the pool’s surface, water and deck.
WARRANTY INFORMATION
Limited Warranty Terms & Conditions
Before installing your cleaner, review and understand all warnings, safety and warranty information in this guide. Failure to follow these
instructionsorimproperinstallation of thecleaner can resultindamage to thepoolfinish or thevinylliner, Pentair WaterPool andSpa,Inc.
disclaimsany liability forrepairs orreplacement to anyof thesestructuresor componentsof the customer’spool.
The Cleaner manufacturer, Pentair Water Pool and Spa, Inc. (“Manufacturer”), hereby provides the following limited warranty to the
purchaser (“Customer”): WHICH IS SUBJECT ONLY TO THE FOLLOWING CONDITIONS AND EXCLUSIONS:
Thislimited warranty does not includereplacement ofparts which becomediscolored dueto exposureto sunlight orchemicals, orparts
which,evenifworn, do notaffectperformanceofthecleaner. Nicks, scratches,fading,discoloration,etc.arecosmeticconditions that
do not affect mechanical performance.Both Manufacturer and Pentair Water Pool and Spa’s dealer reserve the right to deny
any and all warranty claims made for worn parts if the wear does not negatively affect mechanical performance of the
cleaner.
TheCleanerisdesignedtofunctioninaproperlydesigned,constructedandmaintainedpool.Thislimitedwarrantydoesnotextendinthe
circumstances where the pool’s design, construction or maintenance is defective, substandard or inappropriate for the Cleaner’s
operation.
Deterioration, discoloration or brittleness of any pool finish can be caused over time separately by, or in combination with, age, an
imbalance in water chemistry, improper installation, and other factors. Customer hereby disclaims any and all claims, and releases
Manufacturer from any and all claims for damages to any pool plaster or vinyl liner in Customer’s pool by reason of the use and/or
operation of the Cleaner.
UndernocircumstancesshallManufacturerbeliableforanylossordamage,whetherdirect,consequentialorincidental,arisingoutofthe
use or inability to use the Cleaner or the Hose in Customer’s pool.
Thislimitedwarrantydoes not applyto any injury,loss, damage, defect, ormalfunctionof the Cleaneror failureto functionresultingfrom
any failure to operate or maintain the Cleaner in accordance with the directions contained in the Installation and Operation Manual or
operatinginstructionsprovidedbyPentairWaterPoolandSpaoranyinjury, loss,damage,defect,ormalfunction,orfailureto function
resultingfromanyaccident,actsof God, alterationsintheCleanerby anyone other thanManufacturer;ormisuse,unreasonableuse,
tampering,abuse,acts,omissions,failureornegligencebyanyoneotherthanManufacturerincludingbutnotlimitedtosuchdamages
orinjuriestopartsresultingfromimproperinstallation,ordamagetopumppartsresultingfromrunningthepumpdry(e.g.,interruption
inor inadequatesupply of water to internalpump partsdue toloss of prime, or obstructionin linesor otherwise); or damage,defect or
malfunctionresultingfromdefectsin,failureormalfunctionof,ornegligence,abuse,ormisusewithrespecttoequipmentotherthanthe
Cleaner;oranydamageorlossofanynaturewhatsoeverandpersonalinjurycausedduetothepresenceofaforeignobjectinorabout
thepool.
®
®
®
®
5

6
5.
4.
7.
1.
3.
2.
6.
10.
9.
8.
1
I. Preparation Of Your Pool
Before assembling and installing your Kreepy Krauly, your pool should be clean and algae-free so as not
to inhibit the cleaner’s traction. If necessary, make the following preparations before proceeding:
1. Chemically balance the pool water.
2. Brush pool and let the debris settle.
3. Hand vacuum thoroughly.
4. Clean filter and pump strainer basket.
II. Assembly
Remove Kreepy Krauly and all of its parts from the box and check to make sure that all components
were included. Refer to Figure 1.
Components Check List
1. Dive float restrictor
2. Kreepy Krauly
3. Locking end clip
4. Roller bumper strap
5. Hose weights
6. Wings
7. Eyeball diverter and outer ring
8. Hose Protector
9. Valve cap
10. Automatic regulator valve
11. Threaded compression adapter
12. Pleated or Starfish seal
13. Hose – 40 ft. total length (not shown)
14. Installation manual (not shown)
16. Pleated or Starfish seal
17. Hose – 40 ft. total length (not shown)
18. Installation video (not shown)
Step 1. Attach The Wings
Kreepy Krauly’s wings snap into place – no tools are needed. Position the wings so you bring the band
around the main body as shown in Figure 2. Slip the wings into the groove in Kreepy Krauly’s main
body, then snap the band clamp into place.
Main Body
Wings
Serial Number
11.
or
For Concrete Pools Only
Figure 1
Figure 2
9.
10.
11.
12.
8.

7
Step 2. Attach The Seal
Your Kreepy Krauly comes equipped with one of
two seals.The Pleated seal is our universal seal and
works in all pool types: concrete, vinyl, fiberglass,
and tile. And our Starfish seal which is used
exclusively in concrete pools only.
To install either seal locate the words “This Side
Up” and face them towards the main body. Slip
the seal over the footpad – (flat side down towards
pool floor) and pull gently until it seats itself on the
other side in its groove, as illustrated in Figure 3.
The seal must be installed flat side down, pleated/
contoured side up. Once in place, the seal should
rotate and turn freely.
The seals are not reversible. The raised pleats on
the Pleated seal and the contours on the Starfish
seal must face upward. The flat side of the seal
should face down to rest against the pool surface.
Step 3. Attach The Roller Bumper Strap
Insert the bottom end of the strap into the slot
provided on the main body. Insert the top end of the strap into the locking clip attached to the swivel
head. See Figure 4.
Step 4. Attach The Dive Float Restrictor
Snap the dive float restrictor into the lower U-shaped brace between the dive floats. Make sure the
locking tabs on both sides of the dive float restrictor snap securely into place. See Figure 5.
Pleated/Starfish Seals in their Grooves
Flange
Dive Float
Dive Float
Restrictor
Locking
End Clip
Swivel
Head
Main
Body
Flat Tab
Main
Body Main
Body
Pleats of
Pleated Seal
The flat side of seal faces down to rest on the pool’s surface.
(For Concrete Pools Only)
Figure 3
Figure 4 Figure 5

8
Step 5. Attach The Hose Weights And Assemble The Hose
The Kreepy Krauly hose comes in sections which must be assembled. You’ll need enough sections to
reach from where Kreepy Krauly is connected, to the farthest part of your pool, plus one section. You will
also have to attach hose weights to the hose to neutralize the hose’s buoyancy in water. The number of
hose weights required is determined by the maximum depth of your pool. The deeper your pool, the more
weight is needed. The number of hose weights appropriate for your pool is explained in Table A.
Twist and push the female ends onto the
male ends after dipping the ends into the
pool to wet them. See Figure 6. Continue
until you’ve connected all the sections you
need. After connecting the hose weights
to the hose as described in “Table A”, then
connectthehose toKreepyKrauly.SeeFigure 7.
One of the hose sections has 2 female ends.
This section should be fitted last and
attached to the pool’s vacuum connection.
Before attaching the Female/Female
Section to your vacuum connection you will
first need to install the hose protector on to the Female/Female hose section. The hose protector is
used to protect the hose from wear.
NOTE: May substitute 4 inch Female/Female hose.
Male Hose End Female Hose End
TABLE A
Pool depth Weight Placement
4 feet or less 1 weight: 4 to 12 inches from
Kreepy Krauly’s swivel head.
More than 4 feet, 2 weights: one 4 to 12 inches
but less than 7 feet and one 6 feet from
the swivel head.
More than 7 feet, 3 weights: one 4 to 12 inches,
but less than 12 feet one 6 feet and one
10 feet from the swivel head.
More than 12 feet 4 weights:* one 4 to 12 inches,
one 6 feet, one 10 feet,
and one 12 feet from the
swivel head.
* Contact your Pentair Pool Products dealer if you need to purchase additional hose weights.
Swivel Head
4''-12''
6' 10'
Female End of a Male/Female Section
Hose Weights
Female/Female Section
with hose protector
to be added last
NOTE: The hose length
illustrated is not representative
of actual size. You will need to
use more sections than shown.
Your fully assembled Kreepy Krauly should look like this.
Figure 6
Figure 7

9
III. Installation
Kreepy Krauly is designed to work in a wide variety of swimming pools. That’s why we’ve included
certain items (such as a threaded compression adapter and valve cap for the automatic regulator valve) with
your Kreepy Krauly. These may or may not be needed, depending on the particular features of your pool.
Both the standard in-skimmer installation and an optional vacuum line installation are covered in this
manual. Check to see which most closely fits your pool configuration and follow the directions. If the
set-up of your pool is unlike any of the examples, contact your Pentair Pool Products dealer for
assistance or call our toll-free Customer Helpline at 1-800-443-5711.
Standard Installation For pools with one skimmer, using the automatic regulator valve.
The advantage of this installation is that the automatic regulator valve automatically balances the water flow
between the skimmer and Kreepy Krauly. We strongly recommend the use of the automatic regulator
valve for maximum safety and performance. The valve automatically adjusts to changes in the amount of
water flow to provide Kreepy Krauly with the power necessary to ensure proper cleaning performance.
1. Turn the pool pump off.
2. Close the main drain and all suction lines, except the line
from the skimmer to which Kreepy Krauly will be
connected.
3. Remove skimmer basket.
4. Screw the threaded compression adapter into the vacuum
connection in the bottom of the skimmer. See Figure 9.
NOTE: Use two wraps of thread seal tape around
threads to ensure easy removal.
(If the opening in the bottom of the skimmer is not
threaded, use a 2'' hose cone, as shown in Figure 8. It is
not included with your Kreepy Krauly, but can be
purchased from your Pentair Pool Products dealer.)
5. Press the automatic regulator valve into the threaded
compression adapter. The end of the valve that is marked
“Attach Hose This End” must point up. See Figure 9.
6. Place Kreepy Krauly into the pool and allow it to sink to
the floor. Continue to feed the hose vertically down into
the pool until it is completely filled with water and
purged of air.
7. Slide the hose protector into position on the hose to
prevent the hose body from rubbing against the skimmer
wall. See Figure 9.
8. Insert the end of the hose through the skimmer opening
and connect the hose directly onto the automatic regulator
valve.
Attach Hose This End
Automatic
Regulator Valve
Threaded
Adapter
Screw (or press) into
bottom of skimmer
2'' Hose Cone
(not included)
Figure 8
Hose through
Skimmer
Opening
with Hose
protector
Automatic
Regulator
Valve
Threaded
Compression
Adapter
(or 2'' Hose Cone)
Attach
Hose
This End
Top of Skimmer
Figure 9
Female/
Female Hose
may
substitute
4” Female/
Female Hose

Optional Vacuum Line Installation Vacuum Line Installation With Automatic Regulator Valve
in Skimmer.
We recommend the use of the automatic regulator valve to balance water flow between Kreepy Krauly and
the skimmer. When attaching Kreepy Krauly to a dedicated vacuum line, the automatic regulator valve
should be installed in the skimmer.
1. Turn the pool pump off.
2. Close the main drain and all suction lines, except the
skimmer and the vacuum line to which the Kreepy
Krauly will be connected.
3. Thread the snap-lock wall fitting into the end of the
dedicated suction line. Then insert the male end of the 45°
hose connector into the snap-lock fitting. See Figure 10.
NOTE: Use two wraps of thread seal tape around the
threads to ensure easy removal.
4. Place Kreepy Krauly (with the hose and hose weights
assembled and attached) into the pool and allow it to sink
to the floor. NOTE: You will have to remove the
female/female hose section in this installation. Continue
to feed the hose vertically down into the pool until it is
completely filled with water and purged of air.
5. Insert the male hose end of the last hose section into the 45° hose connector or directly into the snap-lock
wall fitting. Reminder: Do not use the female/ female hose section in this installation. See Figure 10.
6. Screw the threaded compression adapter into the vacuum
connection in the bottom of the skimmer. NOTE: Use two
wraps of thread seal tape around the threads to ensure easy
removal. If the opening in the bottom of the skimmer is not
threaded, use a 2'' hose cone, the 2'' hose cone is not provided
but can be purchased from your Pentair Pool Products dealer.
7. To prevent water from flowing through the top of the
automatic regulator valve, fasten the valve cap onto the top
of the regulator valve. This activates the regulator valve and
assures that an accurate amount of water (25 gpm) will flow
through the vacuum line and the Kreepy Krauly. Without the
valve cap, the automatic regulator valve and the cleaner will
not function properly. See Figure 12.
8. Press the automatic regulator valve into the threaded compression adapter. See Figure 12.
10
Accessories NOT PROVIDED:
Snap-Lock Wall Fitting NSF
(Part #GW9530)
45º Hose Connector
(Part #K12078)
Snap-Lock Wall Fitting
45° Hose
Connector
Male/Female
Hose Section
Thread Snap-Lock
into Dedicated
Suction Line
in Pool Wall
Figure 10
Top of Skimmer
Automatic
Regulator
Valve
Threaded
Compression
Adapter
(or 2'' Hose Cone)
Valve
Cap
Automatic
Regulator Valve
Threaded
Adapter
Screw (or press) into
bottom of Skimmer
2'' Hose Cone
(not included)
Attach Hose This End
Figure 11
Figure 12

11
IV. Adjustments
After completing the installation, turn the pool pump on. Allow the pump to run for a couple of minutes
to ensure all air cycles out of the system. Kreepy Krauly should be moving about the pool at a rate of
8 to 12 feet per minute. Check each of the following initial adjustments to Kreepy Krauly at this time.
Hose Length
IMPORTANT: The pump must be on when you check the hose length. The hose contracts when the
pump is operating and will be longer when the pump is off.
With Kreepy Krauly operating, position it at the furthest point of the pool from where it’s attached. (It is
easy to position Kreepy Krauly in the pool by moving it about with your pool pole and brush.) Kreepy
Krauly’s hose should be long enough to reach the end of the pool, plus one hose section. If necessary,
remove extra hose sections from the center portion of hose. Removing center hose sections avoids
having to disturb the hose weight placement. Save extra hose sections for use as needed for replacement.
NOTE: Turn pool pump off when adding or removing hose sections.
Hose Balance
To determine correct hose balance, turn the pump off and observe Kreepy Krauly. Hose balance is
correct when Kreepy Krauly’s seal rests flat on the pool floor and the drive tubes make a 45° angle with
the floor, as shown in Figure 13. Kreepy Krauly achieves the best cleaning coverage when the hose
neither weighs down nor pulls up on the unit. Adjust hose weights one inch at a time as needed, until
proper hose balance is achieved. In pools with both shallow and deep areas, adjust hose weights first in
the deep area and then in the shallow area.
1. Hose Too Light. If the hose rises toward the surface at an angle greater than 45°, move the
weights closer to Kreepy Krauly, or move the first two weights closer to each other.
2. Correct Hose Balance.
3. Hose Too Heavy. If the hose sags
downward at an angle less than
45°, move the weights away from
Kreepy Krauly, or separate the first
two weights away from each other. 1. Hose Too Light
2. Correct Hose
Balance
3. Hose Too
Heavy
Figure 13

Return Line Water Flow
IMPORTANT: The water flow from your return line can push Kreepy Krauly’s hose and affect its
performance. It may cause Kreepy Krauly to steer away from the end of the pool where the return line is
located, or it may cause Kreepy Krauly to remain in one section of the pool. To correct this, use the eyeball
diverter included with your Kreepy Krauly. (If the eyeball does not fit your pool, use the wire diverter
(Part #K121620) accessory available for purchase from your Pentair Pool Products dealer.)
To install the eyeball diverter:
•First make sure your pool pump is off. Remove the original eyeball from the return line at
•the pool by unscrewing the lock ring.
•Replace the original eyeball with the Kreepy Krauly eyeball diverter.
•Replace the lock ring and tighten. Make sure the opening of the eyeball diverter points in
•the proper direction before tightening fully. See “Eyeball Diverter Positions” below.
IMPORTANT: The eyeball diverter must fit snugly into the eyeball fitting. Some eyeball fittings,
like Aqua Leader or Olympic, may be too large for the eyeball diverter. In this situation, use the outer
ring supplied with your Kreepy Krauly to adjust for the discrepancy in size.
•Snap the outer ring onto the eyeball diverter and position it in the first groove as shown in Figure 14.
•Insert the eyeball diverter/outer ring assembly into the eyeball fitting in the return line.
•Install the lock (retaining) ring and tighten. See Figure 14.
Eyeball Diverter Positions
Position the diverter opening to redirect the return line water flow so it does not interfere with Kreepy
Krauly’s movement. Try different positions to see which works best in your pool:
•flow directed along the side of pool (the tile line).
•flow directed downward.
•flow directed against the hose will help steer Kreepy Krauly away from obstructions such as
stairs and ladders.
After installing the eyeball diverter, turn the pool pump on. Kreepy Krauly should begin moving across
the pool floor vacuuming up debris in its path.
12
Eyeball Diverter Wire Diverter (optional)
Lock (Retaining) Ring
Eyeball
Diverter
Pool Deck
Pool Wall
Return
Line
Eyeball
Fitting
Outer Ring
Eyeball Diverter
Snap into
this Groove
Figure 14

13
V. Troubleshooting
Because of the individual characteristics of your pool, some additional adjustments may be required to
get the best performance from your Kreepy Krauly.
If there seems to be a problem, check these common causes of cleaner problems. If you still need help,
call your pool professional or call our toll-free Customer Helpline at 1-800-443-5711.
—Is bottom main drain closed? Close drain
—Is filter clean? Clean filter
—Is pump strainer basket clean? Clean basket
—Is debris blocking the bottom
of Kreepy Krauly? Remove debris
—Are there any leaks in the hose? Replace leaky section
—Is automatic regulator valve
free of debris? Clean valve
If Kreepy Krauly is not moving or not pulsating.
•Check to ensure that the main drain and all suction lines are closed, except for the suction
line to which Kreepy Krauly is attached.
•Check for debris in the filter or pump basket.
•Check for debris in Kreepy Krauly’s flapper. Debris may prevent flapper movement or
restrict flow. See page 13 for instructions.
•Pool pump and filter system may be too small (incapable of providing 25 gallons per minute
water flow). Consult your pool professional.
If Kreepy Krauly stays in one end of the pool.
•Check the return line water flow and redirect as necessary with an eyeball diverter.
Refer to page 9.
•Check that hose is long enough to reach to end of pool. Refer to page 8.
•Check that Kreepy Krauly has proper hose balance. Refer to page 8.
If Kreepy Krauly stays on the main drain.
•Check to ensure that main drain is closed. A pool professional may need to assist you.
•Check to ensure that a main drain grate is installed.
•If main drain is not flush with the pool floor, consult your pool professional.
If Kreepy Krauly slows or stops and air bubbles enter the pool at the return line.
Find and correct the air leak that is causing the pump to lose its prime:
•Check the hose to ensure there are no leaks.
•Check the vacuum connection. It should be submerged so no air enters the system.
•Check the pump basket lid for looseness, cracks, and worn or missing O-rings. If you need
assistance, contact your pool professional.

14
14If Kreepy Krauly is moving too fast.
In most pools, the automatic regulator valve supplies Kreepy
Krauly with the proper amount of water flow. However, if used
with an especially powerful pool pump, the valve can be
overpowered.
•To slow Kreepy Krauly down, a manual by-pass valve
(Part #K12094) accessory is available for purchase from
your Pentair Pool Products dealer. This manual by-pass
can be adjusted to achieve the recommended cleaner
speed of 8 to 12 feet per minute.
•To decrease the speed of Kreepy Krauly, simply remove
the in-line valve cone from the bottom of the automatic
regulator valve and replace it with the manual by-pass as
shown in Figure 15.
•Press the automatic regulator valve into the threaded
compresion adapter (or 2" hose cone if used). The end
of the valve that is marked “Attach Hose This End”
must point up.
•Adjust the manual by-pass while the Kreepy Krauly is
running. Place your hand into the skimmer and turn the
by-pass adjuster one click at a time until the desired
speed of 8-12 feet per minute is reached. See Figure 16.
If Kreepy Krauly pulls air from, or remains at,
the water surface.
•Check to ensure the dive float mechanism is operating
freely and the dive float restrictor is
•installed. (See page 4 for how to install dive float restrictor.)
•Check the automatic regulator valve for its proper installation and ensure it is not clogged
with debris.
•Make sure the water level is at least 3 inches below the pool deck.
•Check to ensure your Kreepy Krauly is operating at the proper speed of 8-12 feet per minute.
If Kreepy Krauly stays at the shallow end steps.
•Check the return line water flow and redirect as necessary with an eyeball diverter. Refer
to page 9.
•Check the automatic regulator valve for its proper installation and ensure it is not clogged
with debris.
•Check that hose is long enough to reach the furthest point of the pool, including pool steps.
Refer to page 8.
•Check that Kreepy Krauly has proper hose balance in shallow end. Refer to page 8.
•Check to ensure your Kreepy Krauly is operating at the proper speed of 8-12 feet per minute.
•Check to ensure the dive float mechanism is operating freely and the dive float restrictor is
installed. (See page 4 for how to install dive float restrictor.)
•Shorten the roller bumper strap by 1⁄2inch. (Pull out upper end of bumper strap from locking end
clip attached to swivel head. Cut 1⁄2inch off, then return bumper strap into locking end clip.)
Automatic
Regulator
Valve
Pull Off
Press On
Manual In-Line
Automatic Regulator Valve
with Manual By-pass
Manual By-pass
Fully Closed Manual By-pass Fully Open
Figure 15
Figure 16

15
If Kreepy Krauly tracks in a repetitive pattern.
•Check the swivel on the top of Kreepy Krauly. It should turn freely.
•Check the return line water flow and re-direct as necessary with an eyeball diverter. Refer
to page 9.
•Check Kreepy Krauly’s hose to ensure it has not become bent or kinked. It only takes one
bent or kinked hose section to hinder the cleaning coverage. One way to check for kinks in
your hose is to lay each section flat on your pool’s deck (or other flat surface). The hose
should be perfectly straight and flat. Do not coil the hose when taking your Kreepy
Krauly out of the pool because it will retain the coil shape, forming a bend or kink.
If Kreepy Krauly gets stuck on pool obstructions such as a
safety ledge, ladders, steps, swim-outs, benches, etc.
• Remove dive float restrictor and install a wall climb adjuster
(Part #K12065). Snap the wall climb adjuster into place as
shown in Figure 17. This will keep Kreepy Krauly on the
pool’s floor and away from pool obstructions. Make sure
the narrow end of the wall climb adjuster points down to the
drive tubes.
• If Kreepy Krauly gets stuck under your pool ladder, install a
Ladder Guard (Part #K12330) according to the instructions
contained in the packaging. (These accessories are available
for purchase from your Pentair Pool Products dealer.)
To Remove Debris From The Flapper
• Sometimes debris may clog the bottom of the cleaner and
prevent flapper movement or restrict flow. The flapper is
located inside the main body and must move freely at all
times. You can see the flapper through the opening in the
baffle plate, when you turn the cleaner upside down as shown
in Figure 18. Jiggle the flapper with your finger or flush the
cavity with a hose to force out any debris lodged inside the
main body.
• If debris is still lodged inside, you must remove the flapper.
First, lift the lip of the foot pad and insert a flat-head
screwdriver along side one of the two tabs found on the
baffle plate. See Figure 19. Push the tab inward with the screwdriver until the baffle plate releases.
Place a finger into the center opening of the baffle plate and pull up until it pops out. Then pull
the flapper out. NOTE: You should be able to do this without taking the foot pad off.
•Once the debris is dislodged, insert the flapper back into the main body and snap the baffle
plate back into position. Be sure that it is securely in place. See Figure 19.
Wall Climb
Adjuster
Dive Float
Figure 17
Bottom View of Cleaner
Flapper is
Inside
Baffle Plate
Foot Pad
Pleated
Seal
Foot Pad
(not necessary to remove)
Baffle Plate Flapper Main Body
Figure 18
Figure 19

16
VI. Kreepy Krauly Parts List
K12164
Dive Float Restrictor
K12157
Dive Float
K12181
Dive Float Clip Kit (2)
K12158
Weight Holder
K12160
Wing Set
K12896
Pleated Seal
K12059
Foot Pad
K12004
Automatic Regulator
Valve
K12161
Roller Bumper Strap Kit
(includes bumper roller
and end clip)
K12156C
Swivel Cone and Bearing
K12163
Drive Tube
Top/Bottom
(1)
K12156
Swivel Head Assembly
K12155
Main Body
-With Exchange Only
(Excludes Flapper)
“Insist on Genuine Kreepy Krauly Parts To Protect Your Warranty”
K12054
Hose Weight
K12961
Valve Cap
K12079
Threaded Compression
Adapter
K12087
Bearing Washer

17
VII. Maintenance
Kreepy Krauly requires almost no maintenance. Visually inspect your Kreepy Krauly from time to time
to make sure that:
•The flapper is moving freely and is not obstructed by debris.
•The foot pad is not excessively worn. When the traction pads on the bottom have worn
down, it is time for replacement.
We recommend that you leave Kreepy Krauly in your pool, except during chemical shock treatments.
During swimming it is easy to unplug Kreepy Krauly and pull it to one side.
When storing Kreepy Krauly, do not coil the hose. Lay the hose flat in an area protected from direct
sunlight. If hose sections are disconnected, try not to disturb the hose weight locations.
Kreepy Krauly’s hose is specially designed to ensure optimum performance from Kreepy Krauly. Should
replacement be required, insist on genuine Kreepy Krauly hose.
VIII. Customer Service
Your satisfaction is important to us, so we’re happy to help you get the best performance possible from
your new Kreepy Krauly. This manual and the video included with your Kreepy Krauly cover
a wide range of performance adjustments, which may apply to your pool.
If you still need help, call your Pentair Pool Products dealer or call our toll-free Customer Helpline
at 1-800-443-5711. Please have your Kreepy Krauly serial number ready when you call.

Notes

Notes

© 2012Pentair Water Pool and Spa, Inc. All rights reserved.
1620 Hawkins Ave., Sanford, NC 27330
[phone] • [phone]
10951 West Los Angeles Ave., Moorepark, CA 93021
[phone] • [phone]
Kreepy Krauly® and Pentair Water Pool and Spa® are trademarks and/or registered trademarks of Pentair Water Pool and Spa, Inc.
and/or its affiliated companies in the United States and/or other countries. Unless noted, names and brands of others that may be used
in this document are not used to indicate an affiliation or endorsement between the proprietors of these names and brands and Pentair
Water Pool and Spa, Inc. Those names and brands may be the trademarks or registered trademarks of those parties or others.
P/N K0130 Rev. E 3/28/12
www.pentairpool.com