Pentair HF User manual

© 2017 Pentair Equipment Protection 89137856Rev. H P/N 89134973© 2017 Pentair Equipment Protection 89137856Rev. H P/N 89134973
Side-Mount Filter Fans and Grilles
HF/HG Models
INSTRUCTION MANUAL
All manuals and user guides at all-guides.com
all-guides.com

© 2017 Pentair Equipment Protection
- 2 - 89137856



+)+*0[
+)+*0[
[ [
3XUFKDVH6HSDUDWHO\

[
[
+)+*0
+)+*0
2SWLRQDO
[
2SWLRQDO
[
TABLE OF CONTENTS
Installation Instructions.......................................................................................................................... 3
Wire Diagrams ........................................................................................................................................ 5
How to Read Model Numbers................................................................................................................ 6
Filter Cleaning / Replacement............................................................................................................... 6
Replacement Parts ................................................................................................................................. 7
Warranty .................................................................................................................................................. 7
All manuals and user guides at all-guides.com

© 2017 Pentair Equipment Protection
89137856 - 3 -
Before cutting holes in the sides of the enclosure, verify all
internal components are clear of the cutting tool to avoid
damaging installed components.
CAUTION
INSTALLATION INSTRUCTIONS
1. Apply cutout template to the side of the enclosure located as desired.
See Figure 1
2. Cutout hole in enclosure using the appropriate cutout size for the model you
purchased.
3. Deburr the cutting edge.
4. Insert fan or grille and push into opening until snapped and locked.
See Figure 2.
5. Mounting fasteners are not required for panel or enclosure material thickness less
than .10 (2.5 mm). For panel or enclosure material thickness between .10 (2.5 mm)
and .14 (3.5 mm), mounting fasteners are recommended. For panel or enclosure
material thickness greater than .14 (3.5 mm), mounting fasteners are required in
order to maintain the IP / Type 12 rating.
6. In order to install the mounting fasteners, removal of the grille is required. Remove
the grille by pulling from the top of the grille to 45° maximum as shown in Figure 3
on page 4. Then pull from the bottom as shown in Figure 4 on page 4.
NOTE: The orientation “Top” directs the louvers downward. This is for reference
only; the assembly can be installed to orient louvers in any direction.
7. It may be necessary to drill out the mounting holes in the filter housing. For model
HF04, use a 1/8 (3 mm) drill bit. For models HF05, HF09, HF10 and HF13, use a
5/32 (4 mm) drill bit.
8. Torque fasteners to 20-25 in-lbs (2.3-2.8 Nm). See Figure 5 on page 4.
9. Install the grille as shown in Figure 2
10. Verify the location of the enclosure with installed filter fan has a minimum clearance of
7.00 (178 mm). See Figure 7 on page 4
11. Wire the filter fan following the Wire Diagrams on page 5 for the appropriate model
being installed.
Figure 1

Figure 2




All manuals and user guides at all-guides.com

© 2017 Pentair Equipment Protection
- 4 - 89137856
Figure 3
45° Maximum
Figure 4
Figure 5
LQOEV
>1P@


Figure 6
1
2
LQ0,1
PP0,1
Figure 7
All manuals and user guides at all-guides.com

© 2017 Pentair Equipment Protection
89137856 - 5 -
WIRE DIAGRAMS
/,1(
92/7$*(
/,1(
92/7$*(
:,5,1*',$*5$0
+)+)+)+)
$&32:(5('
)$1
02725
*5281'
%/.
*51<(/
:+7
/ 1
)$1
02725
/
3(
1
%/.
%51
%/8
*51<(/
*5281'
:,5,1*',$*5$0
+)
$&32:(5('
/,1(
92/7$*(
/,1(
92/7$*(
6((1$0(3/$7(
9'&


%/.
5('
1
/
:,5,1*',$*5$0
+)+)+)+)
'&32:(5('
)$1
02725
6((1$0(3/$7(
9'&
6((
1$0(3/$7(
9'&
6((
1$0(3/$7(
9'&
:,5,1*',$*5$0
+))8//63(('
'&32:(5('
)$1
02725
&21752/
,1387
%/.%/8
:+7

7$&+
287387
<(/
:,5,1*',$*5$0
+)9$5,$%/(63(('
'&32:(5('
)$1
02725
5('
<(/
5('

%/.%/8
:+7

&21752/
,1387
7$&+
287387

63(('
&21752/
9'&
6((
1$0(3/$7(
9'&
6((
1$0(3/$7(
9'&
All manuals and user guides at all-guides.com

© 2017 Pentair Equipment Protection
- 6 - 89137856
HOW TO READ MODEL NUMBERS
HF 04 16 4 0 4
1 2 3 4 5 6
1. Filter fan / Grille
2. Size
3. Voltage: 16 = AC 115/50/60/1
26 = AC 230/50/60/1
24 = DC 24V
48 = DC 48V
4. IP Rating: 4 = IP54
5 = IP55
5. Version
6. Color: 3 = RAL9011 Black
4 = RAL = RAL7035 Light Gray
FILTER CLEANING / REPLACEMENT
Replacement Filter Part Numbers
Fan/Grille Models IP54 / Type 12
(≈ .50 [14 mm] thick) IP55 / Type 12 (≈ .75 [20 mm] thick)
HF/HG04 89134423R ---
HF/HG05 89134424R 89136408R
HF/HG09 89134425R 89136409R
HF/HG10 89134426R 89136410R
HF/HG13 89134427R* 89136411R
*Note: HF/HG13 replacement filters are not approved for IP54; only Type 12.
1. Open louvered grille.
2. Wash filter in warm water. Use mild detergent if necessary.
3. For greasy matter, wash in warm water containing a grease solvent.
4. Do not wring the filter.

45° Maximum
'(16(6,'(,1
All manuals and user guides at all-guides.com
all-guides.com

© 2017 Pentair Equipment Protection
89137856 - 7 -
REPLACEMENT PARTS
Model RAL7035 Light Gray RAL9011 Black
Grille Housing Grille Housing
HF04 89123894SP 89133137SP 89131499SP 89133137SP
HF05 89122973SP 89133138SP 89131495SP 89133138SP
HF09 89122907SP 89133139SP 89131484SP 89133139SP
HF10 89123456SP 89133140SP 89131496SP 89133140SP
HF13 89124454SP HG1300404 89131502SP HG1300403
HG04 89123894SP HG0400404 89131499SP HG0400403
HG05 89122973SP HG0500404 89131495SP HG0500403
HG09 89122907SP HG0900404 89131484SP HG0900403
HG10 89123456SP HG1000404 89131496SP HG1000403
HG13 89124454SP HG1300404 89131502SP HG1300403
WARRANTY
Please register your product and reference the Hoffman Cooling Product Warranty
located here: http://www.pentairprotect.com/en/hoffman/warranty-information
All manuals and user guides at all-guides.com

© 2017 Pentair Equipment Protection 89137856Rev. H P/N 89134973
Pentair Electrical
2100 Homan
Way
Anok
a, MN 55303 USA
+1.763.422.2211
+1.763.576.3200
Pe
ntairProtect.com
All manuals and user guides at all-guides.com